scholarly journals Ferroelectric Induced UV Light-Responsive Memory Devices with Low Dark Current

Electronics ◽  
2021 ◽  
Vol 10 (16) ◽  
pp. 1897
Author(s):  
Hanleem Lee ◽  
Young Tea Chun

We developed solution-processed hybrid photodetectors with a poly (9-vinylcarbazole)/zinc oxide nanoparticle photoactive layer and a poly (vinylidene fluoride-co-trifluoroethylene) ferroelectric copolymer buffer layer on flexible plastic substrates. The presence of a ferroelectric-poling interface layer significantly enhanced the charge transfer and responsivity of the photodetectors under ultraviolet (UV, 365 nm) light exposure. The responsivity of the device reached 250 mA/W at a reverse bias of 5 V and incident light intensity of 27.5 μW/cm2. This responsivity was four times higher than that of a device without the ferroelectric copolymer layer (64 mA/W) under the same conditions. The response time of the device to incident UV light also improved from 322 to 34 ms with the addition of the ferroelectric copolymer layer. In addition, the flexible device exhibited a stable performance in an air environment up to a maximum strain of 0.3 under bending stress. Finally, a UV-light-responsive memory device was successfully fabricated by using the developed hybrid photodetector and liquid crystals. This device showed a colour change from white to black upon UV illumination, and the on-state of the device was maintained for 30 s without light exposure owing to the polarization of poly (vinylidene fluoride-co-trifluoroethylene).

Author(s):  
Santhosh Narendhiran ◽  
Acchutharaman Kunka Ravindran ◽  
Isaac Daniel Rajan Thomas ◽  
Senthil Pandian Muthu ◽  
Ramasamy Perumalsamy

2017 ◽  
Vol 24 (3) ◽  
pp. 327-333 ◽  
Author(s):  
Hairong Li ◽  
Chenglong Xu ◽  
Zongyi Chen ◽  
Ming Jiang ◽  
Chuanxi Xiong

AbstractA poly(vinylidene fluoride) (PVDF) nanocomposite incorporated with polydopamine-coated reduced graphene oxide (rGO@PDOPA) nanosheets has been developed with high dielectric permittivity and low loss for electricity storage applications. Structural analysis indicates that PDOPA was successfully anchored onto rGOs through non-covalent linkage under mild conditions. The presence of PDOPA layer between rGO and PVDF can not only prevent the agglomeration and direct contact of original rGOs but also enhance the interaction between PVDF and rGO and microcapacitor formation. Compared to rGO/PVDF composites, higher dielectric permittivity and lower loss factor were achieved simultaneously in rGO@PDOPA/PVDF nanocomposites at low and moderate frequencies. The PDOPA interface layers are effective in modifying the dielectric characteristics of the composites to increase the dielectric permittivity without the introduction of loss mechanisms. This study demonstrates that PDOPA is an ideal interface layer for the development of new percolative dielectric composites with high dielectric permittivity and low loss.


2008 ◽  
Vol 20 (1) ◽  
pp. 91 ◽  
Author(s):  
Y. S. Akshey ◽  
D. Malakar ◽  
A. K. De

Nuclear transfer is a very effective method for propagation of desired, extinct, and endangered animals as well as for the production of 100% transgenic animals. Enucleated oocytes and somatic cells are required for nuclear cloning. For enucleation, DNA-specific stains are used for visualization of the metaphase (MII) plate in matured oocytes under UV illumination in both micromanipulator-based and handmade cloning techniques. The present study was carried out to produce cloned goat embryos using the handmade cloning approach. Fetal fibroblast cells were used as nuclear donors (passages 3–4). Oocytes were collected from slaughterhouse-derived ovaries and matured in maturation medium (TCM-199 (HEPES modified), 5 µg mL–1 FSH, 10 µg mL–1 LH, 1 µg mL–1 estradiol-17β, 50 µg mL–1 gentamicin, 3 mg mL–1 BSA, and 10% inactivated estrus goat serum) at 38.5�C in 5% CO2 in air with maximum humidity for 24 h. We observed that the formation of transparent protrusion cones on the surface of the in vitro-matured goat oocytes was clearly visible under the stereomicroscope after zona digestion with 2 mg mL–1 pronase. The extent of protrusion cone formation in matured oocytes was 95–100% within 20–30 min in handling medium T 20 (TCM-199 + 20% FCS). The MII plate in the protrusion cone was confirmed (100%) after Hoechst 33342 staining and subsequent UV illumination under the inverted microscope. Zona-free oocytes were bisected on the basis of the protrusion cone by a microblade in medium (T 20 + 2.5 µg mL–1 cytochalasin B) for enucleation. Enucleated demi-oocytes were selected which had no protrusion cone and were without staining. Fetal fibroblasts from confluent monolayers were used. Two demi-oocytes were coupled with one trypsinized fetal fibroblast cell using 200 µg mL–1 phytohemagglutinin. The triplets were fused together with a combination of alternating current (7 V) and direct current (2.31 kV cm–1 for 15 µs with a double pulse) in fusion medium (0.3 m mannitol, 0.1 mM MgSO4, 0.05 mm CaCl2, and 3 mg mL–1 BSA). Four h after fusion, reconstructed oocytes were activated by using 2 µm Ca Ionophore for 5 min at room temperature and incubated with 2 mm 6-dimethylaminopurine at 38.5�C in 5% CO2 in air for 3 h. Activated reconstructed embryos were cultured in embryo development medium (TCM-199, 10% FCS, essential and nonessential amino acids, and 10 mg mL–1 BSA) in the well of the well (WOW) culture system (Vajta et al. 2000 Mol. Reprod. Dev. 55, 258–264) at 38.5�C in 5% CO2 in air. In the present study, fusion, cleavage, and morula and blastocyst formation rates were 180/200 (90%), 72/180 (40%), 56/72 (77%), and 6/56 (11%), respectively. Further studies will be required to optimize blastocyst production. In conclusion, the protrusion cone formation in matured goat oocytes made it convenient for bisection and enucleation without Hoechst staining and UV light exposure, enabling the production of goats from handmade somatic cell cloning. The Council of Scientific and Industrial Research, India, has provided a fellowship to the first author to carry out this research work.


2007 ◽  
Vol 997 ◽  
Author(s):  
Klaus Mueller ◽  
Dipanka Mandal ◽  
Dieter Schmeisser

AbstractWith photoelectron spectroscopy, we study the interface chemistry of the copolymer poly(vinylidene fluoride trifluoroethylene) (P(VDF-TrFE)) and different electrode materials. We compare the interfaces aluminum/P(VDF-TrFE) and PEDOT:PSS/P(VDF-TrFE). PEDOT:PSS is a conductive polymer (Poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate)). The data sug-gest that we have an interface layer for electrodes, made of aluminum. An interface reaction occurs in both cases: for aluminum as top and as bottom electrode. In contrast, the organic PE-DOT:PSS electrode shows no chemical interaction with the P(VDF-TrFE) polymer. The much lower reactivity of organic electrodes, compared to aluminum, gives a direct hint to im-proved functional properties of thin organic ferroelectric films.


2004 ◽  
Vol 19 (10) ◽  
pp. 2989-2996 ◽  
Author(s):  
Gopal K. Mor ◽  
Karthik Shankar ◽  
Oomman K. Varghese ◽  
Craig A. Grimes

N-type nanocrystalline titania is a promising material for use in semiconductor photoelectrochemical cells and, potentially, the solar generation of hydrogen. In this study, we examined the photochemical properties of titania nanotube arrays made by anodization of a starting Ti foil in a fluoride ion containing electrolyte. The absorption properties of the titania nanotube samples were investigated using diffuse reflectance ultraviolet (UV)-visible (vis) spectroscopy, with a broadening of the absorption spectra seen as a function of material phase, nanotube diameter, and Pd sensitization. The magnitude of the anodic photocurrent obtained from the polycrystalline nanotube samples, measured under band gap UV illumination, appeared to be significantly higher than that reported for any other form of nanocrystalline titania. A maximum photoconversion efficiency (UV light exposure at 365 nm, intensity 146 mW/cm2) of 4.8% was obtained for 22 nm diameter nanotubes annealed at 500 °C and coated with a discontinuous palladium layer of 10 nm average effective thickness.


2020 ◽  
Vol 91 (3) ◽  
pp. 31301
Author(s):  
Nabil Chakhchaoui ◽  
Rida Farhan ◽  
Meriem Boutaldat ◽  
Marwane Rouway ◽  
Adil Eddiai ◽  
...  

Novel textiles have received a lot of attention from researchers in the last decade due to some of their unique features. The introduction of intelligent materials into textile structures offers an opportunity to develop multifunctional textiles, such as sensing, reacting, conducting electricity and performing energy conversion operations. In this research work nanocomposite-based highly piezoelectric and electroactive β-phase new textile has been developed using the pad-dry-cure method. The deposition of poly (vinylidene fluoride) (PVDF) − carbon nanofillers (CNF) − tetraethyl orthosilicate (TEOS), Si(OCH2CH3)4 was acquired on a treated textile substrate using coating technique followed by evaporation to transform the passive (non-functional) textile into a dynamic textile with an enhanced piezoelectric β-phase. The aim of the study is the investigation of the impact the coating of textile via piezoelectric nanocomposites based PVDF-CNF (by optimizing piezoelectric crystalline phase). The chemical composition of CT/PVDF-CNC-TEOS textile was detected by qualitative elemental analysis (SEM/EDX). The added of 0.5% of CNF during the process provides material textiles with a piezoelectric β-phase of up to 50% has been measured by FTIR experiments. These results indicated that CNF has high efficiency in transforming the phase α introduced in the unloaded PVDF, to the β-phase in the case of nanocomposites. Consequently, this fabricated new textile exhibits glorious piezoelectric β-phase even with relatively low coating content of PVDF-CNF-TEOS. The study demonstrates that the pad-dry-cure method can potentially be used for the development of piezoelectric nanocomposite-coated wearable new textiles for sensors and energy harvesting applications. We believe that our study may inspire the research area for future advanced applications.


Sign in / Sign up

Export Citation Format

Share Document