scholarly journals Effect of Conical Strip Inserts and ZrO2/DI-Water Nanofluid on Heat Transfer Augmentation: An Experimental Study

Energies ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 4554
Author(s):  
Mohamed Iqbal Shajahan ◽  
Jee Joe Michael ◽  
M. Arulprakasajothi ◽  
Sivan Suresh ◽  
Emad Abouel Nasr ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Test Section ◽  
Volume Concentration ◽  
Swirl Flow ◽  
Performance Ratio ◽  
Transfer Rates ◽  
Heat Transfer Augmentation ◽  
Twist Ratio ◽  
Constant Wall Heat Flux

There is a significant enhancement of the heat transfer rate with the usage of nanofluid. This article describes a study of the combination of using nanofluid with inserts, which has proved itself in attaining higher benefits in a heat exchanger, such as the radiator in automobiles, industries, etc. Nanofluids are emerging as alternative fluids for heat transfer applications due to enhanced thermal properties. In this paper, the thermal hydraulic performance of ZrO2, awater-based nanofluid with various volume concentrations of 0.1%, 0.25%, and 0.5%, and staggered conical strip inserts with three different twist ratios of 2.5, 3.5, and 4.5 in forward and backward flow patterns were experimentally tested under a fully developed laminar flow regime of 0–50 lphthrough a horizontal test pipe section with a length of 1 m with a constant wall heat flux of 280 W as the input boundary condition. The temperatures at equidistant position and across the test section were measured using K-type thermocouples. The pressure drop across the test section was measured using a U-tube manometer. The observed results showed that the use of staggered conical strip inserts improved the heat transfer rates up to that of 130.5%, 102.7%, and 64.52% in the forward arrangement, and similarly 145.03%, 116.57%, and 80.92% in the backward arrangement with the twist ratios of 2.5, 3.5, and 4.5 at the 0.5% volume concentration of ZrO2 nanofluid. It was also seen that the improvement in heat transfer was comparatively lower for the other two volume concentrations considered in this study. The twist ratio generates more swirl flow, disrupting the thermal hydraulic boundary layer. Nanofluids with a higher volume concentration lead to higher heat transfer due to higher effective thermal conductivity of the prepared nanofluid. The thermal performance factor (TPF) with conical strip inserts at all volume concentrations of nanofluids was perceived as greater than 1. A sizable thermal performance ratio of 1.62 was obtained for the backward-arranged conical strip insert with 2.5 as the twist ratio and a volume concentration of 0.5% ZrO2/deionized water nanofluid. Correlations were developed for the Nusselt number and friction factor based on the obtained experimental data with the help of regression analysis.

Influence of Short Helical Tape on Local Convective Heat Transfer and Thermal Performance Characteristics in Turbulent Decaying Swirl Flow

2010 ◽  
Vol 8 (1) ◽  
Author(s):  
Smith Eiamsa-ard ◽  
Vichan Kongkaitpaiboon ◽  
Khwanchit Wongcharee
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Thermal Performance ◽  
Swirl Flow ◽  
Transfer Rates ◽  
Friction Factors ◽  
Plain Tube ◽  
Uniform Wall ◽  
Uniform Wall Heat Flux

This paper reports the experimental investigation of local convective heat transfer enhancement, flow friction and thermal performance factor behaviors in the tube fitted with the short helical tapes (SHTs) acting as decaying swirl flow generators. The tapes with three different helical tape angles (? = 90°, 135° and 180°) and three different channel numbers (N = 2, 3 and 4 channels) were tested under the uniform wall heat flux condition. The performance of each tape is compared with the performance of the plain tube subject to the same pumping power. The experimental results show that the heat transfer rates and friction factors of the tube with SHTs are respectively in range of 1.15 to 1.9 and 1.49 to 2.31 times of those in the plain, corresponding to thermal performances between 0.98 and 1.46. The correlations for Nusselt number (Nu) as a function of Reynolds number (Re), Prandtl number (Pr), helical tape angle (?) and the number of channel (N) are also developed.

Heat Transfer Augmentation From Extended Surface Using Dimples

2018 ◽  
Author(s):  
Jay D. Mehta ◽  
Fay N. Colah ◽  
Anurag P. Rao ◽  
Vineeta P. Pendse ◽  
Vyankatesh U. Bagal ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Transfer Rate ◽  
Surface Modifications ◽  
Exposed Surface ◽  
Transfer Rates ◽  
Heat Transfer Augmentation ◽  
Extended Surface ◽  
Extended Surfaces ◽  
Exposed Surface Area

This paper concentrates on comparing dimples to improve the heat transfer rate from extended surfaces under forced convection conditions. Dimples are milled on the surface of the fins while keeping the exposed surface area between the various designs as constant. Spherical dimples, ellipsoidal dimples, cylindrical dimples, and pyramidal dimples are selected as part of the paper. Experimental results are compared with results obtained from simulation. The paper concludes that surface modifications improve the heat transfer rates. The paper also compares the thermal performance of various shapes of dimples.

Numerical Analysis of Flow Structure and Heat Transfer Characteristics in Dimpled Channels With Secondary Protrusions

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Yonghui Xie ◽  
Zhongyang Shen ◽  
Di Zhang ◽  
Phillip Ligrani
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Numerical Analysis ◽  
Thermal Performance ◽  
The Other ◽  
Combination Effect ◽  
Enhancement Ratio ◽  
Heat Transfer Characteristics ◽  
Transfer Rates ◽  
Heat Transfer Augmentation

Dimple structure is an effective heat transfer augmentation approach on coolant channel due to its advantage on pressure penalty. The implication of secondary protrusion, which indicates protrusion with smaller dimension than dimple, will intensify the Nusselt number Nu inside dimple cavity without obvious extra pressure penalty. The objective of this study is to numerically analyze the combination effect of dimples and secondary protrusion. Different protrusion–dimple configurations including protrusion print-diameter Dp, protrusion–dimple gap P, and staggered angle α are investigated. From the results, it is concluded that the implication of secondary protrusion will considerably increase the heat transfer rates inside dimple cavity. Cases 4 and 6 possess the highest Nusselt number enhancement ratio Nu/Nu0 reaching up to 2.1–2.2. The additional pressure penalty brought by the protrusion is within 15% resulting in total friction ratio f/f0 among the range of 1.9–2.1. Dimpled channels with secondary protrusions possess higher thermal performance factor TP, defined as (Nu/Nu0)/(f/f0)1/3, among which cases 4 and 6 are the optimal structures. Besides this, the TP of protrusion–dimple channels are comparable to the other typical heat transfer devices, and higher TP can be speculated after a more optimal dimple shape or combination with ribs and fins.

Comparative Study on Heat Transfer Enhancement of Low Volume Concentration of Al2O3–Water and Carbon Nanotube–Water Nanofluids in Laminar Regime Using Helical Screw Tape Inserts

2013 ◽  
Vol 4 (4) ◽  
Author(s):  
Sandesh S. Chougule ◽  
S. K. Sahu
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Volume Concentration ◽  
Constant Heat Flux ◽  
Transfer Enhancement ◽  
Straight Pipe ◽  
Maximum Enhancement ◽  
Flux Boundary Condition ◽  
Twist Ratio ◽  
Heat Flux Boundary Condition

An experimental study has been carried out to evaluate the heat transfer and friction factor characteristics of helical screw inserts in Al2O3–water and carbon nanotubes (CNT)–water nanofluids through a straight pipe in laminar flow regime with constant heat flux boundary condition. Tests have been performed by using 0.15% volume concentration Al2O3–water and CNT–water nanofluid with helical tape inserts of twist ratio (TR) = 1.5, 2.5, and 3. The helical screw tape inserts with CNT–water nanofluid exhibits higher thermal performance compared to Al2O3–water nanofluid. The maximum enhancement in heat transfer was obtained for CNT–water nanofluid with helical tape inserts of TR = 1.5. The increase in pressure drop of Al2O3–water nanofluid with helical screw tape inserts is found to be higher compared to CNT–water nanofluid with helical screw tape inserts at lower value of TR. For both the nanofluids (CNT–water and Al2O3–water), the thermal performance factor was found to be greater than unity for all TRs.

scholarly journals Comparative Studies on Thermal Performance of Conic Cut Twist Tape Inserts with SiO2and TiO2Nanofluids

2015 ◽  
Vol 2015 ◽  
pp. 1-14 ◽  
Author(s):  
Sami D. Salman ◽  
Abdul Amir H. Kadhum ◽  
Mohd S. Takriff ◽  
Abu Bakar Mohamad
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Thermal Performance ◽  
Volume Concentration ◽  
Twisted Tape ◽  
Maximum Heat ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
Maximum Heat Transfer ◽  
Twist Ratio

This paper presents a comparison study on thermal performance conic cut twist tape inserts in laminar flow of nanofluids through a constant heat fluxed tube. Three tape configurations, namely, quadrant cut twisted tape (QCT), parabolic half cut twisted tape (PCT), and triangular cut twisted (VCT) of twist ratioy= 2.93 and cut depthde= 0.5 cm were used with 1% and 2% volume concentration of SiO2/water and TiO2/water nanofluids. Typical twist tape with twist ratio ofy= 2.93 was used for comparison. The results show that the heat transfer was enhanced by increasing of Reynolds number and nanoparticles concentration of nanofluid. The results have also revealed that the use of twist tape enhanced the heat transfer coefficient significantly and maximum heat transfer enhancement was achieved by the presence of triangular cut twist tape insert with 2% volume concentration of SiO2nanofluid. Over the range investigated, the maximum thermal performance factor of 5.13 is found with the simultaneous use of the SiO2nanofluid at 2% volume concentration VCT at Reynolds number of 220. Furthermore, new empirical correlations for Nusselt number, friction factor, and thermal performance factor are developed and reported.

Thermal Enhancement in Tubes with Dual Twisted Tapes

2015 ◽  
Vol 751 ◽  
pp. 239-244
Author(s):  
Pratchya Somravysin ◽  
Smith Eiamsa-ard ◽  
Wayo Changcharoen ◽  
Vichan Kongkaitpaiboon ◽  
Monsak Pimsarn
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Thermal Performance ◽  
Transfer Rate ◽  
Simple Algorithm ◽  
Twisted Tapes ◽  
Twist Ratio ◽  
Constant Wall Heat Flux ◽  
Thermal Phenomena ◽  
Volume Method

Influence of the dual twisted tapes (DTs) on the heat transfer enhancement in a circular tube is reported. The effects of twist ratio (y/w = 2.0, 3.0 and 4.0) on the heat transfer rate, friction factor, and thermal performance factor in a tube under constant wall heat flux were investigated in turbulent regions. Computations, based on a finite volume method, and the SIMPLE algorithm, were carried out by QUICK schemes. From the numerical results, heat transfer rate and pressure loss increased as twist ratio of tape (y/w) decreased. Based on the same pumping power consumption, the optimum thermal performance was achieved by the use of the tapes with twist ratio of 3.0. In addition, the predictions of flow-thermal phenomena (streamline, velocity vector, TKE and local Nusselt number) are also described.

Heat Transfer Augmentation in a Round Tube with 60o Winglet Pair Inserts

2014 ◽  
Vol 931-932 ◽  
pp. 1188-1192 ◽  
Author(s):  
Suriya Chokphoemphun ◽  
Pattarapan Tongyote ◽  
Pongjet Promvonge ◽  
Withada Jedsadaratanachai ◽  
Teerapat Chompookham
Keyword(s):  
Heat Transfer ◽  
Operating Conditions ◽  
Transfer Enhancement ◽  
Airflow Velocity ◽  
Tubular Heat Exchanger ◽  
Transfer Rates ◽  
Heat Transfer Augmentation ◽  
Thermal Enhancement ◽  
Constant Wall Heat Flux ◽  
Thermal Enhancement Factor

The experimental study on heat transfer enhancement in a tubular heat exchanger fitted with 60o winglet pairs is carried out by varying airflow velocity in turbulent region in the test section having a constant wall heat-flux. Effects of three blockage ratios (BR=e/D= 0.1, 0.15 and 0.2) and three pitch ratios (PR=P/D= 1, 1.5 and 2) of the winglet pairs on heat transfer rates in the terms of Nusselt number (Nu) and pressure loss in the form of friction factor (f) are examined. The experimental results illustrated that the tube with winglet pair insert provides the heat transfer rate higher than the smooth tube around 1.7 to 2.6 times, depending upon operating conditions. The thermal enhancement factor for using the winglet-pair turbulator is in a range of 1.03 - 1.31.

Experimental study of thermohydraulic characteristics and irreversibility analysis of novel axial corrugated tube with spring tape inserts

2020 ◽  
Vol 92 (3) ◽  
pp. 30901
Author(s):  
Suvanjan Bhattacharyya ◽  
Debraj Sarkar ◽  
Ulavathi Shettar Mahabaleshwar ◽  
Manoj K. Soni ◽  
M. Mohanraj
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Thermal Performance ◽  
Working Fluid ◽  
The Novel ◽  
Heat Exchanger Tube ◽  
Heat Transfer Augmentation ◽  
Corrugated Tube ◽  
The Impact ◽  
Exchanger Tube

The current study experimentally investigates the heat transfer augmentation on the novel axial corrugated heat exchanger tube in which the spring tape is introduced. Air (Pr = 0.707) is used as a working fluid. In order to augment the thermohydraulic performance, a corrugated tube with inserts is offered. The experimental study is further extended by varying the important parameters like spring ratio (y = 1.5, 2.0, 2.5) and Reynolds number (Re = 10 000–52 000). The angular pitch between the two neighboring corrugations and the angle of the corrugation is kept constant through the experiments at β = 1200 and α = 600 respectively, while two different corrugations heights (h) are analyzed. While increasing the corrugation height and decreasing the spring ratio, the impact of the swirling effect improves the thermal performance of the system. The maximum thermal performance is obtained when the corrugation height is h = 0.2 and spring ratio y = 1.5. Eventually, correlations for predicting friction factor (f) and Nusselt number (Nu) are developed.

scholarly journals Execution of a Smart Prediction Tool to Evaluate Thermal Performance in a heat exchanger by using Single Elliptical Leaf Strips with altered Angle

2019 ◽  
Vol 8 (11) ◽  
pp. 123-131
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Thermal Performance ◽  
Heat Exchangers ◽  
Industrial Applications ◽  
Generalized Regression Neural Network ◽  
Prediction Tool ◽  
Pressure Drops ◽  
Transfer Rates ◽  
Mass Flow Rates

Heat exchangers are prominent industrial applications where engineering science of heat transfer and Mass transfer occurs. It is a contrivance where transfer of energy occurs to get output in the form of energy transfer. This paper aims at finding a solution to improve the thermal performance in a heat exchanger by using passive method techniques. This experimental and numerical analysis deals with finding the temperature outlets of cold and hot fluid for different mass flow rates and also pressure drop in the tube and the annular side by adding an elliptical leaf strip in the pipe at various angles. The single elliptical leaf used in experiment has major to minor axes ratios as 2:1 and distance of 50 mm between two leaves are arranged at different angular orientations from 0 0 to 1800 with 100 intervals. Since it’s not possible to find the heat transfer rates and pressure drops at every orientation of elliptical leaf so a generalized regression neural network (GRNN) prediction tool is used to get outputs with given inputs to avoid experimentation. GRNN is a statistical method of determining the relationship between dependent and independent variables. The values obtained from experimentation and GRNN nearly had precise values to each other. This analysis is a small step in regard with encomiastic approach for enhancement in performance of heat exchangers

Thermal Performance of a Heat Storage Module Using Calcium Chloride Hexahydrate

1984 ◽  
Vol 106 (1) ◽  
pp. 106-111 ◽  
Author(s):  
D. Dietz
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Phase Change ◽  
Calcium Chloride ◽  
Thermal Performance ◽  
Heat Storage ◽  
Heat Transfer Area ◽  
Transfer Rates ◽  
Chloride Hexahydrate ◽  
Change Material

The thermal performance of an air-heated/cooled, phase-change, heat stoage module was tested and evaluated. The module (rated at 38.7 kWh) consist of 130 vertically oriented tubes filled with 729 kg (1607 lb) of calcium chloride hexahydrate and enclosed in a rectangular box. Heat transfer rates measured during charging and discharging decreased with time as a result of decreasing effective heat transfer area and increasing thermal resistance of the phase-change material. These two dominant effects are included in a proposed mathematical model that predicted the experimental data.

Sign in / Sign up

Export Citation Format

Share Document