scholarly journals Stochastic Analysis-Based Volt–Var Curve of Smart Inverters for Combined Voltage Regulation in Distribution Networks

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2785
Author(s):  
Dongwon Lee ◽  
Changhee Han ◽  
Gilsoo Jang
Keyword(s):  
Reactive Power ◽  
Control Method ◽  
Flow Analysis ◽  
Voltage Control ◽  
Distribution Networks ◽  
Voltage Regulation ◽  
Load Flow ◽  
Renewable Energy Resources ◽  
Voltage Profile ◽  
Smart Inverters

The proliferation of renewable energy resources (RES), especially solar photovoltaic (PV) generation resources, causes overvoltage and line overloading in distribution networks. This study proposes a two-level volt–var control method based on multiple timescales. The on-load tap changer (OLTC) operates on an hourly timescale, to regulate the voltage on the secondary winding. In the 15-minutes timescale, PV-connected smart inverters and static var compensators (SVCs) are obliged to compensate the reactive power for the voltage control at the point of common coupling. In the multi-timescale voltage control framework, this study proposes a new multi-sectional volt–var curve (MSVVC) of a PV inverter. The objective of the MSVVC is to minimize the energy loss in the network, improve the voltage profile, and obtain the operational margin of other reactive power compensation devices. In the process of determining the optimal parameters of the MSVVC, stochastic modeling-based load flow analysis is utilized to consider the intermittency and uncertainty of RES generation. The effectiveness of the proposed method is verified on the IEEE 33-bus system in comparison with the conventional volt–var curve cases.

scholarly journals Linear Sensitivity Modelling Useful for Voltage Control Analysis Using Power Injections from DER

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4749
Author(s):  
Ulises D. Lubo-Matallana ◽  
Miguel Ángel Zorrozua ◽  
José Félix Miñambres
Keyword(s):  
Distribution System ◽  
Reactive Power ◽  
Distribution Networks ◽  
Voltage Regulation ◽  
Load Flow ◽  
System Response ◽  
Control Analysis ◽  
Voltage Profile ◽  
Reactive Compensation ◽  
And Control

The injection of apparent power to self-consumption buses generates voltage variations during network operation, which, when properly monitored, could support voltage regulation and control. In this paper, we propose a linear sensitivity modelling, quite useful for studies of voltage regulation with distributed energy resources (DER). This modelling consists of two analytical improvement steps: first, a full formulation for the voltage deviations, and second, the influence of line capacitance as Q-injections at the points of common couplings (PCCs). Our proposal is based on the linear topological sensitivity of an existing network (as a function of the line parameters X, R, and Bc), branch power flow (active–reactive power (P-Q)), and power injections at the PCCs. Here, the linear sensitivity algorithm is applied to a modified IEEE 33-bus distribution system to demonstrate its extended effectiveness to voltage monitoring and control scenarios. Its application estimates and compensates in a better way the voltage deviations with regard to the operating desired voltage (|V|op) constraints, using distributed power injections at the PCCs. Numerical results always showed a curtailment of the relative error against common simplifications of the electrical modelling in steady-state, thus simulating two critical scenarios of operation production–consumption for the existing system response. The proposed algorithm was validated considering as reference the voltage profile outputs of the load flow analysis, using the Newton–Raphson method via DIgSILENT, in terms of its accuracy, silhouette shape along the feeder and with regard to the application of reactive compensation as an analytical case study for voltage improvement in active distribution networks.

scholarly journals Load flow analysis using newton raphson method in presence of distributed generation

2021 ◽  
Vol 12 (1) ◽  
pp. 489
Author(s):  
Tebbakh Noureddine ◽  
Labed Djamel
Keyword(s):  
Reactive Power ◽  
Flow Analysis ◽  
Distribution Networks ◽  
Test System ◽  
Load Flow ◽  
Voltage Profile ◽  
Real Power ◽  
Load Flow Analysis ◽  
Newton Raphson ◽  
Raphson Method

<p>Distributed generations (DG), specially including renewable sources such as wind and sun are offering several opportunities for the currently in existence distribution networks and becoming one of the keys of treatment of its problems. Knowing the effects of each kind of DG on distribution networks is a primordial task because DG impacts differ from one kind to another. In this paper, we have analyzed and compared the effects of two kinds of DG, DG which provides real power only and DG which provides real power and reactive power at the same time connected at the critical bus in DN on the voltage profile, real and reactive power losses. We have proposed Newton Raphson method using Matlab to investigate the impacts of these two kinds of DG on 57-bus IEEE distribution test system. The obtained results have been exposed in detail at the end of this paper.</p>

scholarly journals Optimal Allocation of Capacitor Bank for Loss Minimization and Voltage Improvement Using Analytical Method

SCITECH Nepal ◽  
2019 ◽  
Vol 14 (1) ◽  
pp. 1-7
Author(s):  
Avinash Khatri KC ◽  
Tika Ram Regmi
Keyword(s):  
Distribution System ◽  
Distribution Systems ◽  
Optimal Allocation ◽  
Reactive Power ◽  
Capacitor Bank ◽  
Minimum Cost ◽  
Distribution Networks ◽  
Standard Test ◽  
Load Flow ◽  
Voltage Profile

An electric distribution system plays an important role in achieving satisfactory power supply. The quality of power is measured by voltage stability and profile of voltage. The voltage profile is affected by the losses in distribution system. As the load is mostly inductive on the distribution system and requires large reactive power, most of the power quality problems can be resolved with requisite control of reactive power. Capacitors are often installed in distribution system for reactive power compensation. This paper presents two stage procedures to identify the location and size of capacitor bank. In the first stage, the load flow is carried out to find the losses of the system using sweep algorithm. In the next stage, different size of capacitors are initialized and placed in each possible candidate bus and again load flow for the system is carried out. The objective function of the cost incorporating capacitor cost and loss cost is formulated constrained with voltage limits. The capacitor with the minimum cost is selected as the optimized solution. The proposed procedure is applied to different standard test systems as 12-bus radial distribution systems. In addition, the proposed procedure is applied on a real distribution system, a section of Sallaghari Feeder of Thimi substation. The voltage drops and power loss before and after installing the capacitor were compared for the system under test in this work. The result showed better voltage profiles and power losses of the distribution system can be improved by using the proposed method and it can be a benefit to the distribution networks.

scholarly journals Power factor control of PV generators in local distribution networks using fuzzy logic concept

2018 ◽  
Vol 7 (2.28) ◽  
pp. 362
Author(s):  
Raed A. Shalwala
Keyword(s):  
Fuzzy Logic ◽  
Control System ◽  
Power Factor ◽  
Fuzzy Logic Control ◽  
Reactive Power ◽  
Distribution Network ◽  
Voltage Control ◽  
Distribution Networks ◽  
Voltage Regulation ◽  
Logic Control

One of the most important operational requirements for any electrical power network for both distribution and transmission level is voltage control. Many studies have been carried out to improve or develop new voltage control techniques to facilitate safe connection of distributed generation. In Saudi Arabia, due to environmental, economic and development perspectives, a wide integration of photovoltaic (PV) genera-tion in distribution network is expected in the near future. This development in the network may cause voltage regulation problems due to the interaction with the existing conventional control system. In a previous paper, a control system has been described using a fuzzy logic control to set the on-line tap changer for the primary substation. In this paper a new control system is proposed for controlling the power factor of individual PV invertors based on observed correlation between net active and reactive power at each connection. A fuzzy logic control has been designed to alter the power factor for the remote invertors from the secondary substation to keep the feeder voltage within the permissible limits. In order to confirm the validity of the proposed method, simulations are carried out for a realistic distribution network with real data for load and solar radiation. Results showing the performance of the new control method are presented and discussed.  

scholarly journals Secondary voltage regulation based on average voltage control

TecnoLógicas ◽  
2018 ◽  
Vol 21 (42) ◽  
pp. 63-78
Author(s):  
Edwin H. Lopera-Mazo ◽  
Jairo Espinosa
Keyword(s):  
Control System ◽  
Power Systems ◽  
Reactive Power ◽  
Voltage Control ◽  
Voltage Regulation ◽  
Voltage Profile ◽  
Real Power ◽  
Power Resources ◽  
Control Actions ◽  
Secondary Voltage

This paper compares a conventional Secondary Voltage Regulation (SVR) scheme based on pilot nodes with a proposed SVR that takes into account average voltages of control zones. Voltage control significance for the operation of power systems has promoted several strategies in order to deal with this problem. However, the Hierarchical Voltage Control System (HVCS) is the only scheme effectively implemented with some relevant applications into real power systems.The HVCS divides the voltage control problem into three recognized stages. Among them, the SVR is responsible for managing reactive power resources to improve network voltage profile. Conventional SVR is based on dividing the system into some electrically distant zones and controlling the voltage levels of some specific nodes in the system named pilot nodes, whose voltage levels are accepted as appropriate indicators of network voltage profile.The SVR approach proposed in this work does not only consider the voltage on pilot nodes, but it also takes the average voltages of the defined zones to carry out their respective control actions. Additionally, this innovative approach allows to integrate more reactive power resources into each zone according to some previously defined participation factors.The comparison between these strategies shows that the proposed SVR achieves a better allocation of reactive power in the system than conventional SVR, and it is able to keep the desired voltage profile, which has been expressed in terms of network average voltage.

scholarly journals Voltage Control Method for Active Distribution Networks Based on Regional Power Coordination

Energies ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 4364 ◽  
Author(s):  
Ou-Yang ◽  
Long ◽  
Du ◽  
Diao ◽  
Li
Keyword(s):  
Power Control ◽  
Reactive Power ◽  
Control Method ◽  
Voltage Control ◽  
Distribution Networks ◽  
Active Power ◽  
Reactive Power Control ◽  
Safety Issues ◽  
Bus Voltage ◽  
The Relationship

As loads connected to active distribution network (ADN) grow, ADN’s voltage safety issues are becoming more serious. At present, the solution is mainly to build more distributed generation (DG) or to adjust the reactive power in the whole network, but the former needs a lot of investment while the latter requires a large amount of communication equipment and it takes a long time to calculate the adjustment amount of reactive power and to coordinate reactive power compensation equipment. When the loads are heavy, there will still be drawbacks of insufficient reactive power. Therefore, this paper analyzes the relationship between the active power, reactive power, and the voltage in the ADN. Through the autonomous region (AR) division, a voltage control method based on the active power variation and adjustable power in the AR is proposed. According to the relationship between the amount of active power and the adjustable amount active power, the active power control, the reactive power control, and the coordinated control of active power reactive power control are adopted to adjust the DGs’ output to stabilize the bus voltage. The simulation results show that the proposed method can effectively improve the voltage control capability of ADN and can enable it to operate normally under greater power changes. Through the control method in this paper, the communication requirements are greatly reduced and the calculation time is effectively shortened and is more adaptable.

Micro Static Var Compensator for Over-Voltage Control in Distribution Networks with High Penetration of Rooftop Photovoltaic Systems

2016 ◽  
Vol 839 ◽  
pp. 54-58 ◽  
Author(s):  
Piyadanai Pachanapan ◽  
Phudit Inthai
Keyword(s):  
Power Control ◽  
Reactive Power ◽  
Control Method ◽  
Voltage Control ◽  
Distribution Networks ◽  
Static Var Compensator ◽  
Pv System ◽  
Reactive Power Control ◽  
Pv Systems ◽  
Dynamic Voltage

A micro static var compensator (µSVC) is introduced in this work to prevent the over-voltage problems in radial distribution networks with high number of rooftop photovoltaic (PV) connections. The µSVC is aimed to use in the PV system that has the fixed-power factor inverter, which cannot provide the active voltage controllability. The µSVC is a small shunt compensator installed parallel with the PV system and providing the automatic reactive power support to deal with the dynamic voltage variations at the point of common coupling. Two reactive power control methods, Q(P) and Q(V), can be employed into each µSVC depending on the location of PV systems. Moreover, the coordinated reactive power control among µSVCs, without communication system requirement, is presented for enhancing the Volt-Var controllability to the group of PV systems located in the same feeder. The dynamic voltage control performances are examined on simulation in DIgSILENT PowerFactory software. The results showed that the proposed control method can mitigate the rise of voltage level sufficiently.

scholarly journals Enhancement of Voltage Profile by Optimal Placement of Distributed Generators with UPFC in Distribution Networks

2019 ◽  
Vol 8 (6) ◽  
pp. 2733-2738 ◽  
Keyword(s):  
Transmission Lines ◽  
Network Reliability ◽  
Distribution Network ◽  
Flow Analysis ◽  
Distribution Networks ◽  
Load Flow ◽  
Optimal Placement ◽  
Voltage Profile ◽  
Load Flow Analysis ◽  
Distributed Generators

The Distributed generation and fast operating power electronic devices are attracting more attention due to their effective solution for improvement in the voltage profile, to meet the increasing power consumption, reduction in the power loss, enhancement in the power transfer capacity of the transmission lines, reducing the overloading of the entire network. The optimal placement of DG and FACTs devices plays key role in improvement of the network reliability and voltage stability. In this paper exhaustive load flow analysis is carried out for optimal placement of DG and UPFC. The proposed method is tested on 40 bus distribution network. The obtained results are satisfactory in terms of improvement in the overall performance of the distribution network.

scholarly journals Elimination of the Impact Produced by DG Units on the Voltage Profile of Distribution Networks

2020 ◽  
Vol 2020 ◽  
pp. 1-8
Author(s):  
Saad Ouali ◽  
Abdeljabbar Cherkaoui
Keyword(s):  
Control Systems ◽  
Control Strategy ◽  
Reactive Power ◽  
Voltage Control ◽  
Distribution Networks ◽  
Total System ◽  
Voltage Profile ◽  
Voltage Control Strategy ◽  
Facts Devices ◽  
The Impact

In this paper, an alternative strategy for real-time control of active distribution network voltage is developed, not by controlling the bus voltage as in the various centralized, decentralized, and local approaches presented in literature but rather by only eliminating the impact produced by active and reactive power of distributed generation (DG) units on the voltage of all network nodes and keeping the traditional voltage control systems dealing with the same constraints of passive systems. In literature, voltage deterioration introduced by DGs has been reported as one of the main obstacles for the interconnection of large amounts of DG units to the existing networks. In this paper, the novel control strategy is based on a sensitivity formula developed to calculate the compensation needed for additional distributed flexible AC transmission system (D-FACTS) devices to push and pull the exact reactive power and to eliminate the impact produced by DGs on the network voltage profile. The criteria of the allocation of the var devices and the required network reinforcement are developed in this paper, considering all possible topology structures, and an innovative codification method is introduced to reduce the needed computation time and communication data to actualize the sensitivity coefficients and get the proposed control approach flexible with network topology reconfiguration. The risk of the conflict of the proposed control system with the traditional voltage equipment is reduced due to the fast capability of D-FACTS devices to regulate their reactive power in finer granularity. A case study of two meshed IEEE 15-bus feeders is introduced to compare the voltage behavior with and without the presence of DG units and to evaluate the total system losses. The proposed method could be used for the interconnection of the first generation units in emerging networks, which does not yet have an active voltage control strategy, as it could be used for DG units not able to be connected to existing centralized control systems and it could also be used as the principal voltage control strategy, with the extension for several neighboring units and the preservation of the traditional voltage control systems.

Sign in / Sign up

Export Citation Format

Share Document