scholarly journals Probabilistic Load Flow–Based Optimal Placement and Sizing of Distributed Generators

Energies ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7857
Author(s):  
Ferdous Al Hossain ◽  
Md. Rokonuzzaman ◽  
Nowshad Amin ◽  
Jianmin Zhang ◽  
Mahmuda Khatun Mishu ◽  
...  
Keyword(s):  
Distribution System ◽  
Distribution Network ◽  
Operating Cost ◽  
Distribution Networks ◽  
Load Flow ◽  
Optimal Placement ◽  
Power Losses ◽  
Power Distribution System ◽  
Power Load ◽  
Point Estimation Method

Distributed generation (DG) is gaining importance as electrical energy demand increases. DG is used to decrease power losses, operating costs, and improve voltage stability. Most DG resources have less environmental impact. In a particular region, the sizing and location of DG resources significantly affect the planned DG integrated distribution network (DN). The voltage profiles of the DN will change or even become excessively increased. An enormous DG active power, inserted into an improper node of the distribution network, may bring a larger current greater than the conductor’s maximum value, resulting in an overcurrent distribution network. Therefore, DG sizing and DG location optimization is required for a systematic DG operation to fully exploit distributed energy and achieve mutual energy harmony across existing distribution networks, which creates an economically viable, secure, stable, and dependable power distribution system. DG needs to access the location and capacity for rational planning. The objective function of this paper is to minimize the sum of investment cost, operation cost, and line loss cost utilizing DG access. The probabilistic power flow calculation technique based on the two-point estimation method is chosen for this paper’s load flow computation. The location and size of the DG distribution network are determined using a genetic algorithm in a MATLAB environment. For the optimum solution, the actual power load is estimated using historical data. The proposed system is based on the China distribution system, and the currency is used in Yuan. After DG access, active and reactive power losses are reduced by 53% and 26%, respectively. The line operating cost and the total annual cost are decreased by 53.7% and 12%, respectively.

scholarly journals Configurations of Aromatic Networks for Power Distribution System

2020 ◽  
Vol 12 (10) ◽  
pp. 4317
Author(s):  
K. Prakash ◽  
F. R. Islam ◽  
K. A. Mamun ◽  
H. R. Pota
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Smart Grids ◽  
Sustainable Energy ◽  
Distribution Network ◽  
Geographical Location ◽  
Distribution Networks ◽  
Self Healing ◽  
Power Distribution System ◽  
Improve Energy Efficiency

A distribution network is one of the main parts of a power system that distributes power to customers. While there are various types of power distribution networks, a recently introduced novel structure of an aromatic network could begin a new era in the distribution levels of power systems and designs of microgrids or smart grids. In order to minimize blackout periods during natural disasters and provide sustainable energy, improve energy efficiency and maintain stability of a distribution network, it is essential to configure/reconfigure the network topology based on its geographical location and power demand, and also important to realize its self-healing function. In this paper, a strategy for reconfiguring aromatic networks based on structures of natural aromatic molecules is explained. Various network structures are designed, and simulations have been conducted to justify the performance of each configuration. It is found that an aromatic network does not need to be fixed in a specific configuration (i.e., a DDT structure), which provides flexibility in designing networks and demonstrates that the successful use of such structures will be a perfect solution for both distribution networks and microgrid systems in providing sustainable energy to the end users.

Swarm-Intelligence-Based Optimal Placement and Sizing of Distributed Generation in Distribution Network

2018 ◽  
pp. 29-48 ◽  
Author(s):  
Mahesh Kumar ◽  
Perumal Nallagownden ◽  
Irraivan Elamvazuthi ◽  
Pandian Vasant ◽  
Luqman Hakim Rahman
Keyword(s):  
Distributed Generation ◽  
Radial Distribution ◽  
Distribution System ◽  
Voltage Stability ◽  
Reactive Power ◽  
Distribution Network ◽  
Stability Index ◽  
Pso Algorithm ◽  
Distribution Networks ◽  
Optimal Placement

In the distribution system, distributed generation (DG) are getting more important because of the electricity demands, fossil fuel depletion and environment concerns. The placement and sizing of DGs have greatly impact on the voltage stability and losses in the distribution network. In this chapter, a particle swarm optimization (PSO) algorithm has been proposed for optimal placement and sizing of DG to improve voltage stability index in the radial distribution system. The two i.e. active power and combination of active and reactive power types of DGs are proposed to realize the effect of DG integration. A specific analysis has been applied on IEEE 33 bus system radial distribution networks using MATLAB 2015a software.

An Analytical Approach for DG Placement in Reconfigured Distribution Networks

2016 ◽  
Vol 5 (3) ◽  
pp. 137
Author(s):  
Sarfaraz Nawaz ◽  
Ajay Bansal ◽  
M. P. Sharma
Keyword(s):  
Distribution System ◽  
Mathematical Formulation ◽  
Distribution Networks ◽  
Optimal Placement ◽  
Type I ◽  
Total System ◽  
Power Losses ◽  
Real Power ◽  
Novel Approach ◽  
Operating Constraints

<p>A novel approach is proposed in this paper for optimal placement of DG units in reconfigured distribution system with the aim of reduction of real power losses while satisfying operating constraints. The proposed analytical method for optimal DG placement is developed based on a new mathematical formulation. Type-I and type-II DG units are used here. The results of the proposed technique are validated on IEEE 69 bus distribution system. The level of DG penetration is also considered in a range of 0–50% of total system load. A novel index is also proposed which incorporates level of DG penetration and percentage reduction in real power losses. The results are promising when compared with recently proposed algorithms.</p>

scholarly journals Multiple DGs for Reducing Total Power Losses in Radial Distribution Systems Using Hybrid WOA-SSA Algorithm

2019 ◽  
Vol 2019 ◽  
pp. 1-20 ◽  
Author(s):  
Khalid Mohammed Saffer Alzaidi ◽  
Oguz Bayat ◽  
Osman N. Uçan
Keyword(s):  
Radial Distribution ◽  
Distribution Systems ◽  
Distribution Networks ◽  
Load Flow ◽  
Optimal Placement ◽  
Total Power ◽  
Voltage Profile ◽  
Power Losses ◽  
Standard Case ◽  
Whale Optimization

Distributed generators (DGs) are currently extensively used to reduce power losses and voltage deviations in distribution networks. The optimal location and size of DGs achieve the best results. This study presents a novel hybridization of new metaheuristic optimizations in the last two years, namely, salp swarm algorithm (SSA) and whale optimization algorithm (WOA), for optimal placement and size of multi-DG units in radial distribution systems to minimize total real power losses (kW) and solve voltage deviation. This hybrid algorithm is implemented on IEEE 13- and 123-node radial distribution test systems. The OpenDSS engine is used to solve the power flow to find the power system parameters, such power losses, and the voltage profile through the MATLAB coding interface. Results describe the effectiveness of the proposed hybrid WOA-SSA algorithm compared with those of the IEEE standard case (without DG), repeated load flow method, and WOA and SSA algorithms applied independently. The analysis results via the proposed algorithm are more effective for reducing total active power losses and enhancing the voltage profile for various distribution networks and multi-DG units.

scholarly journals A Novel Analytical Approach for Optimal Placement and Sizing of Distributed Generations in Radial Electrical Energy Distribution Systems

2021 ◽  
Vol 13 (18) ◽  
pp. 10224
Author(s):  
Sasan Azad ◽  
Mohammad Mehdi Amiri ◽  
Morteza Nazari Heris ◽  
Ali Mosallanejad ◽  
Mohammad Taghi Ameli
Keyword(s):  
Radial Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Voltage Stability ◽  
Reducing Power ◽  
Distribution Networks ◽  
Active Power ◽  
Optimal Placement ◽  
Power Losses ◽  
Active Power Losses

Considering the strong influence of distributed generation (DG) in electric distribution systems and its impact on network voltage losses and stability, a new challenge has appeared for such systems. In this study, a novel analytical algorithm is proposed to distinguish the optimal location and size of DGs in radial distribution networks based on a new combined index (CI) to reduce active power losses and improve system voltage profiles. To obtain the CI, active power losses and voltage stability indexes were used in the proposed approach. The CI index with sensitivity analysis was effective in decreasing power losses and improving voltage stability. Optimal DG size was determined based on a search algorithm to reduce active power losses. The considered scheme was examined through IEEE 12-bus and 33-bus radial distribution test systems (RDTS), and the obtained results were compared and validated in comparison with other available methods. The results and analysis verified the effectiveness of the proposed algorithm in reducing power losses and improving the distribution system voltage profiles by determining the appropriate location and optimal DG size. In IEEE 12 and 33 bus networks, the minimum voltage increased from 0.9434 p.u and 0.9039 p.u to 0.9907 p.u and 0.9402 p.u, respectively. Additionally, the annual cost of energy losses decreased by 78.23% and 64.37%, respectively.

scholarly journals Examination of the Chance Constrained Optimal WT Penetration Level in Distorted Distribution Network with Wind Speed and Load Uncertainties

2021 ◽  
Vol 11 (4) ◽  
pp. 7311-7320
Author(s):  
I. C. Barutcu
Keyword(s):  
Wind Speed ◽  
Distribution System ◽  
Distribution Network ◽  
Flow Analysis ◽  
Harmonic Distortion ◽  
Distribution Networks ◽  
Optimization Method ◽  
Load Flow ◽  
Chance Constraint ◽  
Harmonic Load

Harmonic penetration can be problematic by the growing interconnection of Wind Turbines (WTs) in distribution networks. Since the active power outputs of WTs and loads in the distribution system have uncertainties, the optimal WT penetration level problem can be considered to have a stochastic nature. In this study, this problem is taken into account in the stochastic optimization method with the consideration of uncertainties in wind speed and distribution network load profile. Chance constraint programming is taken into account in the determination of optimal WT penetration levels by applying the Genetic Algorithm (GA) along with Monte Carlo Simulation (MCS). The harmonic power flow analysis based on the decoupled harmonic load flow approach is employed in the distorted distribution network. Chance constraints are considered for the harmonic issues such as the Total Harmonic Distortion of Voltage (VTHD), Individual Harmonic Distortion of Voltage (VIHDh), and Root Mean Square of Voltage (VRMS).

scholarly journals Optimizing the Formation of DMAs in a Water Distribution Network Applying Geometric Partitioning (GP) and Gaussian Mixture Models (GMMs)

Proceedings ◽  
2018 ◽  
Vol 2 (11) ◽  
pp. 601 ◽  
Author(s):  
Stavroula Chatzivasili ◽  
Katerina Papadimitriou ◽  
Vasilis Kanakoudis ◽  
Menelaos Patelis
Keyword(s):  
Distribution System ◽  
Water Distribution ◽  
Distribution Network ◽  
Water Distribution Network ◽  
Distribution Networks ◽  
Gaussian Mixture ◽  
Optimal Placement ◽  
Water Age ◽  
Optimal Separation ◽  
Geometric Partitioning

In the last three decades, the need of achieving a reliable water distribution system has become more eminent for both the consumer’s satisfaction and the efficient management of water sources. The purpose of this paper is to provide an optimal separation of a water distribution network (WDN) into District Metered Areas (DMAs) in order to ensure that the delivered water is of proper age and pressure. At first, the water distribution network is divided into smaller areas via the method of Geometric Partitioning, which is based on Recursive Coordinate Bisection (RCB). Subsequently, Gaussian Mixture Modelling (GMM) solution is applied, obtaining an optimal placement of isolation valves and separation of the WDN into DMAs. The performance of the proposed system is evaluated on two different networks and is compared against the Genetic Algorithm (GA) tool, constituting a very promising approach, especially for sizeable water distribution networks due to the diminished running time and the noteworthy reduction of pressure and water age.

scholarly journals Minimization of Network Power Losses in the AC-DC Hybrid Distribution Network through Network Reconfiguration Using Soft Open Point

Electronics ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 326
Author(s):  
Muhammad Omer Khan ◽  
Abdul Wadood ◽  
Muhammad Irfan Abid ◽  
Tahir Khurshaid ◽  
Sang Bong Rhee
Keyword(s):  
Distribution System ◽  
Distribution Network ◽  
Distribution Networks ◽  
Energy Resources ◽  
Network Reconfiguration ◽  
Power Losses ◽  
Network Configuration ◽  
Hybrid Distribution ◽  
Open Point ◽  
Network Power

The Alternating Current-Direct Current (AC-DC) hybrid distribution network has received attention in recent years. Due to advancement in technologies such as the integration of renewable energy resources of DC–type output and usage of DC loads in the distribution network, the modern distribution system can meet the increasing energy demand with improved efficiency. In this paper, a new AC-DC hybrid distribution network architecture is analyzed that considers distributed energy resources (DER) in the network. A network reconfiguration scheme is proposed that uses the AC soft open point (AC-SOP) and the DC soft open point (DC-SOP) along with an SOP selection algorithm for minimizing the network power losses. Subsequently, the real-time data for DER and load/demand variation are considered for a day-a-head scenario for the verification of the effectiveness of the network reconfiguration scheme. The results show that the proposed network reconfiguration scheme using AC-SOP and DC-SOP can successfully minimize the network power losses by modifying the network configuration. Finally, the effectiveness of the proposed scheme in minimizing the network power losses by the upgraded network configuration is verified by constructing an AC-DC hybrid distribution network by combining two IEEE 33-bus distribution networks.

scholarly journals Enhancement of Voltage Profile by Optimal Placement of Distributed Generators with UPFC in Distribution Networks

2019 ◽  
Vol 8 (6) ◽  
pp. 2733-2738 ◽  
Keyword(s):  
Transmission Lines ◽  
Network Reliability ◽  
Distribution Network ◽  
Flow Analysis ◽  
Distribution Networks ◽  
Load Flow ◽  
Optimal Placement ◽  
Voltage Profile ◽  
Load Flow Analysis ◽  
Distributed Generators

The Distributed generation and fast operating power electronic devices are attracting more attention due to their effective solution for improvement in the voltage profile, to meet the increasing power consumption, reduction in the power loss, enhancement in the power transfer capacity of the transmission lines, reducing the overloading of the entire network. The optimal placement of DG and FACTs devices plays key role in improvement of the network reliability and voltage stability. In this paper exhaustive load flow analysis is carried out for optimal placement of DG and UPFC. The proposed method is tested on 40 bus distribution network. The obtained results are satisfactory in terms of improvement in the overall performance of the distribution network.

scholarly journals Power losses evaluation in low voltage distribution network: a case study of 250 kVA, 11/0.416 kV substation

2022 ◽  
Vol 25 (1) ◽  
pp. 35
Author(s):  
Emad Hussen Sadiq ◽  
Rakan Khalil Antar ◽  
Safer Taib Ahmed
Keyword(s):  
Distribution System ◽  
Low Voltage ◽  
Distribution Network ◽  
Distribution Networks ◽  
System Capacity ◽  
Power Losses ◽  
Three Phase ◽  
The Right ◽  
A Current

Nowadays, the electrical system is more complicated duet to the continuous growing. Power losses is the biggest challenges for distribution network operators. There are several causes for technical losses. Losses caused by unbalanced phase current are one of the main reasons which can be minimized by small investment through dedicating a technical line staff. As a result of connecting many single loads to three phase four wire power supplies, the current flowing in each phase will be unequal and accordingly there will be a current flowing in the neutral wire. Unbalancing currents in phases can lead to increase the conductor temperature and accordingly the conductor resistance is higher which contribute to increase the power losses. Loss reduction can lead to enormous utility saving. Besides, it increases system capacity and save more money which can be used later for future planted system. This study concentrated on the amount of copper losses in distribution networks as a result of unequal loading of the three phases four wires network. The distribution network is more efficient and more economic assuming that the right procedure is applied to balance the distribution system and achieve the required calculations which require a little investment.

Sign in / Sign up

Export Citation Format

Share Document