scholarly journals The Role of Fluorine in F-La/TiO2 Photocatalysts on Photocatalytic Decomposition of Methanol-Water Solution

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 2867 ◽  
Author(s):  
Miroslava Edelmannová ◽  
Lada Dubnová ◽  
Martin Reli ◽  
Vendula Meinhardová ◽  
Pengwei Huo ◽  
...  
Keyword(s):  
Electrochemical Impedance ◽  
Diffuse Reflectance Spectroscopy ◽  
Water Solution ◽  
Pure Tio2 ◽  
Photocatalytic Decomposition ◽  
Tio2 Photocatalysts ◽  
X Ray ◽  
Optical And Electronic Properties ◽  
Production Of Hydrogen

F-La/TiO2 photocatalysts were studied in photocatalytic decomposition water-methanol solution. The structural, textural, optical, and electronic properties of F-La/TiO2 photocatalysts were studied by combination of X-ray powder diffraction (XRD), nitrogen physisorption, Ultraviolet–visible diffuse reflectance spectroscopy (UV-Vis DRS), Electrochemical impedance spectroscopy (EIS), and X-ray fluorescence (XPS). The production of hydrogen in the presence of 2.8F-La/TiO2 was nearly up to 3 times higher than in the presence of pure TiO2. The photocatalytic performance of F-La/TiO2 increased with increasing photocurrent response and conductivity originating from the higher amount of fluorine presented in the lattice of TiO2.

scholarly journals Enhanced Photocatalytic Activity of CuWO4 Doped TiO2 Photocatalyst Towards Carbamazepine Removal under UV Irradiation

Separations ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 25
Author(s):  
Chukwuka Bethel Anucha ◽  
Ilknur Altin ◽  
Emin Bacaksız ◽  
Tayfur Kucukomeroglu ◽  
Masho Hilawie Belay ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Pure Tio2 ◽  
Component Part ◽  
Energy Yield ◽  
Mechanical Agitation ◽  
X Ray

Abatement of contaminants of emerging concerns (CECs) in water sources has been widely studied employing TiO2 based heterogeneous photocatalysis. However, low quantum energy yield among other limitations of titania has led to its modification with other semiconductor materials for improved photocatalytic activity. In this work, a 0.05 wt.% CuWO4 over TiO2 was prepared as a powder composite. Each component part synthesized via the sol-gel method for TiO2, and CuWO4 by co-precipitation assisted hydrothermal method from precursor salts, underwent gentle mechanical agitation. Homogenization of the nanopowder precursors was performed by zirconia ball milling for 2 h. The final material was obtained after annealing at 500 °C for 3.5 h. Structural and morphological characterization of the synthesized material has been achieved employing X-ray diffraction (XRD), Fourier transform infra-red (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) N2 adsorption–desorption analysis, Scanning electron microscopy-coupled Energy dispersive X-ray spectroscopy (SEM-EDS), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectroscopy (UV-vis DRS) for optical characterization. The 0.05 wt.% CuWO4-TiO2 catalyst was investigated for its photocatalytic activity over carbamazepine (CBZ), achieving a degradation of almost 100% after 2 h irradiation. A comparison with pure TiO2 prepared under those same conditions was made. The effect of pH, chemical scavengers, H2O2 as well as contaminant ion effects (anions, cations), and humic acid (HA) was investigated, and their related influences on the photocatalyst efficiency towards CBZ degradation highlighted accordingly.

scholarly journals Photocatalytic decomposition of methanol-water solution over N-La/TiO2 photocatalysts

2019 ◽  
Vol 469 ◽  
pp. 879-886 ◽  
Author(s):  
Lada Dubnová ◽  
Magdalena Zvolská ◽  
Miroslava Edelmannová ◽  
Lenka Matějová ◽  
Martin Reli ◽  
...  
Keyword(s):  
Water Solution ◽  
Photocatalytic Decomposition ◽  
Tio2 Photocatalysts

Role of chromium in anomalous behaviour of the passive layer in Ni-Cr-Mo alloys in 1M HCl solution

CORROSION ◽  
10.5006/3767 ◽  
2022 ◽  
Author(s):  
Malvika Karri ◽  
Amit Verma ◽  
J.B. Singh ◽  
Sunil Kumar Bonagani ◽  
U.K. Goutam
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Corrosion Behaviour ◽  
Underlying Mechanism ◽  
Passive Layer ◽  
X Ray ◽  
Superior Corrosion Resistance ◽  
Hcl Solution ◽  
Cr2o3 Layer

This work seeks to understand the underlying mechanism involved in passivity of Ni-Cr-Mo alloys in a less concentrated HCl solution (1M) by systematically varying contents of Cr and Mo solutes in model Ni-Cr-Mo alloys. Corrosion behaviour was evaluated based on potentiodynamic polarisation tests carried out in conjunction with electrochemical impedance and x-ray photoelectron spectroscopies of passive films that formed on alloys during their exposure to the HCl solution. Results have shown that an increase in Mo alone is not sufficient to improve the corrosion resistance of the alloys at lower concentrations of HCl. Optimum concentrations of Cr and Mo solutes have been found to be in the vicinity of ~17 wt.% Cr and ~19 wt.% Mo for superior corrosion resistance of the alloys. This was attributed to the protection of the Cr2O3 layer as a consequence of the enrichment of Mo6+ ions in the passive film in 1M HCl solution.

scholarly journals Defective TiO2 Core-Shell Magnetic Photocatalyst Modified with Plasmonic Nanoparticles for Visible Light-Induced Photocatalytic Activity

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 672 ◽  
Author(s):  
Zuzanna Bielan ◽  
Agnieszka Sulowska ◽  
Szymon Dudziak ◽  
Katarzyna Siuzdak ◽  
Jacek Ryl ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Phenol Degradation ◽  
Magnetic Core ◽  
Magnetic Photocatalyst ◽  
X Ray ◽  
Transmission Electron ◽  
First Time

In the presented work, for the first time, the metal-modified defective titanium(IV) oxide nanoparticles with well-defined titanium vacancies, was successfully obtained. Introducing platinum and copper nanoparticles (NPs) as surface modifiers of defective d-TiO2 significantly increased the photocatalytic activity in both UV-Vis and Vis light ranges. Moreover, metal NPs deposition on the magnetic core allowed for the effective separation and reuse of the nanometer-sized photocatalyst from the suspension after the treatment process. The obtained Fe3O4@SiO2/d-TiO2-Pt/Cu photocatalysts were characterized by X-ray diffractometry (XRD) and specific surface area (BET) measurements, UV-Vis diffuse reflectance spectroscopy (DR-UV/Vis), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Further, the mechanism of phenol degradation and the role of four oxidative species (h+, e−, •OH, and •O2−) in the studied photocatalytic process were investigated.

scholarly journals Role of Vanadium Additions on the Corrosion Mitigation of Ti-6Al-xV Alloy in Simulated Body Fluid

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 903 ◽  
Author(s):  
El-Sayed M. Sherif ◽  
Sameh A. Ragab ◽  
Hany S. Abdo
Keyword(s):  
Simulated Body Fluid ◽  
Body Fluid ◽  
Immersion Time ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cyclic Potentiodynamic Polarization ◽  
Elemental Analyses ◽  
Corrosion Behaviors

The manufacturing of different Ti-6Al-xV (x = 2, 4, 6, and 8 wt.%) alloys using a mechanical alloying technique was reported. The corrosion behaviors of these newly fabricated alloys after 1, 24, and 48 h exposure to a simulated body fluid (SBF) were assessed using cyclic potentiodynamic polarization, electrochemical impedance spectroscopy, and chronoamperometric measurements. Surface morphology and elemental analyses after corrosion for 48 h in SBF were reported using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) examinations. An X-ray diffraction investigation characterized the phase analyses. All results indicated that the increase of V content significantly decreases both uniform and pitting corrosion. This effect also increases with prolonging the immersion time to 48 h before measurement.

scholarly journals Significantly Enhanced Aqueous Cr(VI) Removal Performance of Bi/ZnO Nanocomposites via Synergistic Effect of Adsorption and SPR-Promoted Visible Light Photoreduction

Catalysts ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 426 ◽  
Author(s):  
Xiaoya Yuan ◽  
Zijuan Feng ◽  
Jianjun Zhao ◽  
Jiawei Niu ◽  
Jiasen Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Synergistic Effect ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray ◽  
Enhanced Absorption ◽  
Bismuth Nanoparticles ◽  
Effective Transfer

Bismuth nanoparticles (BiNPs) and Zinc Oxide photocatalysts (BiNPs/ZnO) with different Bi loadings were successfully prepared via a facile chemical method. Their morphology and structure were thoroughly characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), UV-Vis (Ultraviolet-Visible) diffuse reflectance spectroscopy (DRS), photoluminescence spectra (PL), and electrochemical impedance spectroscopy (EIS). The results showed that a modification of hexagonal wurtzite-phase ZnO nanoparticles with Bi is achievable with an intimate interfacial interaction within its composites. The performance of the photocatalytic Cr(VI) removal under visible light irradiation indicated that BiNPs/ZnO exhibited a superior removal performance to bare ZnO, Bi, and the counterpart sample prepared using a physical mixing method. The excellent performance of the BiNPs/ZnO photocatalysts could be ascribed to the synergistic effect between the considerable physical Cr (VI) adsorption and enhanced absorption intensity in the visible light region, due to the surface plasmon resonance (SPR) as well as the effective transfer and separation of the photogenerated charge carriers at the interface.

scholarly journals Perovskite-type LaFeO3: Photoelectrochemical Properties and Photocatalytic Degradation of Organic Pollutants Under Visible Light Irradiation

Catalysts ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 342 ◽  
Author(s):  
Mohammed Ismael ◽  
Michael Wark
Keyword(s):  
Visible Light ◽  
Photocatalytic Degradation ◽  
Visible Light Irradiation ◽  
Metal Ion ◽  
Electrochemical Impedance ◽  
Diffuse Reflectance Spectroscopy ◽  
Light Irradiation ◽  
Complexing Agent ◽  
X Ray ◽  
Perovskite Type

Perovskite-type oxides lanthanum ferrite (LaFeO3) photocatalysts were successfully prepared by a facile and cost-effective sol-gel method using La(NO)3 and Fe(NO)3 as metal ion precursors and citric acid as a complexing agent at different calcination temperatures. The properties of the resulting LaFeO3 samples were characterized by powder X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDXS), UV-Vis diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectra (IR), transmission electron microscopy (TEM), N2 adsorption/desorption and photoelectrochemical tests. The photoactivity of the LaFeO3 samples was tested by monitoring the photocatalytic degradation of Rhodamine B (RhB) and 4-chlorophenol (4-CP) under visible light irradiation, the highest photocatalytic activity was found for LaFeO3 calcined at 700 °C, which attributed to the relatively highest surface area (10.6 m2/g). In addition, it was found from trapping experiments that the reactive species for degradation were superoxide radical ions (O2−) and holes (h+). Photocurrent measurements and electrochemical impedance spectroscopy (EIS) proved the higher photo-induced charge carrier transfer and separation efficiency of the LaFeO3 sample calcined at 700 °C compared to that that calcined at 900 °C. Band positions of LaFeO3 were estimated using the Mott-Schottky plots, which showed that H2 evolution was not likely.

scholarly journals Synthesis of BiSI/Ag2CO3 Composite Material for Photocatalytic Degradation of Rhodamine B under Visible Light

2021 ◽  
Author(s):  
Rui Zhang ◽  
ziyin chen ◽  
Chen Zhao ◽  
Kunlin Zeng ◽  
Lu Cai ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photocatalytic Degradation ◽  
Rhodamine B ◽  
Photocatalytic Performance ◽  
Electrochemical Impedance ◽  
Diffuse Reflectance Spectroscopy ◽  
Mass Ratio ◽  
X Ray ◽  
Visible Light Driven

Abstract A novel binary BiSI/Ag2CO3 photocatalyst with excellent visible light-driven photocatalytic performance was prepared. The products were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS) and electrochemical impedance spectroscopy (EIS). The photocatalytic activity of the samples were evaluated by photocatalytic degradation of rhodamine B(RhB) under the irradiation of visible light. The results showed that the BiSI improves the photocatalytic activity of BiSI/Ag2CO3. Moreover, when the mass ratio of BiSI in BiSI/Ag2CO3 composites was 40%, the as-prepared BiSI/Ag2CO3 composite exhibited the best photocatalytic activity for degrading RhB. Finally, the possible mechanism for photodegradation over the BiSI/Ag2CO3 composites is also proposed.

scholarly journals Green hydrogen production by solar photocatalysis using Pt-TiO2 nanosheets with reactive facets

2021 ◽  
Vol 28 (2) ◽  
pp. 75-81
Author(s):  
Bin Wang ◽  
Daniel H C Wan ◽  
Altair T F Cheung ◽  
Denis Y C Leung ◽  
Xiao-Ying Lu ◽  
...  
Keyword(s):  
Hydrogen Production ◽  
Diffuse Reflectance Spectroscopy ◽  
Production Performance ◽  
Photocatalytic Hydrogen Production ◽  
X Ray ◽  
Transmission Electron ◽  
Tio2 Nanosheets ◽  
Production Of Hydrogen ◽  
Green Production ◽  
Renewable Hydrogen

Green production of hydrogen is essential for the development of a hydrogen economy. In this study, the photocatalytic water-splitting technology is developed to harness solar energy for production of renewable hydrogen. Pt-TiO2 nanosheets were fabricated by a facile hydrothermal method, followed by photo-reduction of Pt(acac)2 on B,F-codoped TiO2 with reactive facets. The as-prepared photocatalysts were characterised by transmission electron microscopy (TEM), X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX) and UV-vis diffuse reflectance spectroscopy (DRS). The photocatalytic hydrogen production performance was systematically investigated under UV-visible irradiation. The parametric results indicate that the TiO2 nanosheet structure, Pt loading and photocatalyst concentration have significant impacts on the photocatalytic hydrogen production. The highest hydrogen production rate obtained is 5,086 μmol h-1g-1.

scholarly journals Synthesis of C-N-S-Tridoped TiO2 from Vietnam Ilmenite Ore and Its Visible Light-Driven-Photocatalytic Activity for Tetracyline Degradation

2020 ◽  
Vol 2020 ◽  
pp. 1-14 ◽  
Author(s):  
Nguyen Thi Lan ◽  
Vo Hoang Anh ◽  
Hoang Duc An ◽  
Nguyen Phi Hung ◽  
Dao Ngoc Nhiem ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Nitrogen Adsorption ◽  
Photocatalytic Decomposition ◽  
Raman Scattering Spectroscopy ◽  
X Ray ◽  
Visible Light Driven

In this study, C-N-S-tridoped TiO2 composite was fabricated from TiO2 prepared from ilmenite ore and thiourea by means of hydrothermal method. The obtained material was characterized by X-ray diffraction, Raman scattering spectroscopy, UV-Vis diffuse reflectance spectroscopy, nitrogen adsorption-desorption isotherms, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). It was found that C-N-S-tridoped TiO2 material has a large specific surface area, showing good photocatalytic activity on the degradation of antibiotic tetracycline in visible light region. The study on the mechanism of tetracycline photodegradation using the liquid chromatography with mass spectrometry was performed. It was found that tetracycline has been degraded over C-N-S-tridoped TiO2 catalyst into many different intermediates which can eventually be converted into CO2 and H2O. The kinetics of photocatalytic decomposition of tetracycline were investigated. In addition, the obtained material could catalyze well the degradation of other antibiotics (ciprofloxacin and chloramphenicol) and dyes (rhodamine-B, methylene blue, and organe red). The catalyst was stable after five recycles with slight loss of catalytic activity, which indicates great potential for practical application of C-N-S-tridoped TiO2 catalyst in treatment of wastewater containing tetracycline in particular or antibiotics in general.

Sign in / Sign up

Export Citation Format

Share Document