scholarly journals Use of Mining Waste to Produce Ultra-High-Performance Fibre-Reinforced Concrete

Materials ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2457
Author(s):  
Jesús Suárez González ◽  
Iñigo Lopez Boadella ◽  
Fernando López Gayarre ◽  
Carlos López-Colina Pérez ◽  
Miguel Serrano López ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
Research Work ◽  
Fine Fraction ◽  
Mining Industry ◽  
Silica Sand ◽  
Fibre Reinforced Concrete ◽  
Natural Aggregates ◽  
By Products ◽  
High Performance Fibre

This research work analyses the influence of the use of by-products from a fluorite mine to replace the fine fraction of natural aggregates, on the properties of Ultra-High-Performance Fibre-Reinforced Concrete (UHPFRC). Replacing natural aggregates for different kinds of wastes is becoming common in concrete manufacturing and there are a number of studies into the use of waste from the construction sector in UHPFRC. However, there is very little work concerning the use of waste from the mining industry. Furthermore, most of the existing studies focus on granite wastes. So, using mining sand waste is an innovative alternative to replace natural aggregates in the manufacture of UHPFRC. The substitutions in this study are of 50%, 70% and 100% by volume of 0–0.5 mm natural silica sand. The results obtained show that the variations in the properties of consistency, compressive strength, modulus of elasticity and tensile strength, among others, are acceptable for substitutions of up to 70%. Therefore, fluorite mining sand waste is proved to be a viable alternative in the manufacturing of UHPFRC.

scholarly journals Behaviour of UHPFRCs in compression under high stress-rates

2018 ◽  
Vol 183 ◽  
pp. 02005
Author(s):  
Ezio Cadoni ◽  
Matteo Dotta ◽  
Daniele Forni
Keyword(s):  
Reinforced Concrete ◽  
Mechanical Behaviour ◽  
High Performance ◽  
High Stress ◽  
Slight Reduction ◽  
Fibre Reinforcement ◽  
Fibre Reinforced Concrete ◽  
Dynamic Event ◽  
The Matrix ◽  
High Performance Fibre

The paper presents the results obtained on cylindrical Ultra High Performance Fibre Reinforced Concrete specimens with diameter of 30mm and a height of 60mm under compression at high stress rate (1.7–2.3 TPa/s). Four different percentages of fibre reinforcement are considered (1, 2, 3, and 4% fibre content) and compared with the results of the matrix (UHPC). A slight reduction of the strength and fracture time with the introduction of fibres is observed. The experimental results are analysed and discussed with the intent to better understand the mechanical behaviour of UHPFRC materials in case of dynamic event under service loading conditions.

The new Pinel Bridge in Rouen, the fifth French road bridge using ultra high performance fibre-reinforced concrete components

2008 ◽  
Vol 17 (11) ◽  
pp. 316-317
Author(s):  
Daniel de MATTEIS ◽  
Pierre MARCHAND ◽  
Aude PETEL ◽  
Thierry THIBAUX ◽  
Nicolas FABRY ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
Fibre Reinforced Concrete ◽  
High Performance Fibre

scholarly journals The Effect of the Morphology of Coarse Aggregate on the Properties of Self-Compacting High-Performance Fibre-Reinforced Concrete

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1372 ◽  
Author(s):  
Krzysztof Ostrowski ◽  
Łukasz Sadowski ◽  
Damian Stefaniuk ◽  
Daniel Wałach ◽  
Tomasz Gawenda ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Physical And Mechanical Properties ◽  
Concrete Mixture ◽  
Rheological Parameters ◽  
Transverse Strain ◽  
Fibre Reinforced Concrete ◽  
High Performance Fibre

When understanding the effect of the morphology of coarse aggregate on the properties of a fresh concrete mixture, the strength and deformability of self-compacting high-performance fibre-reinforced concrete (SCHPFRC) can be seen to be critical for its performance. In this research, regular and irregular grains were separated from granite coarse aggregate. The morphology of these grains was described while using digital image analysis. As a result, the aspect ratio, roundness and area ratio were determined in order to better understand this phenomenon. Then, the principal rheological, physical, and mechanical properties of SCHPFRC were determined. The obtained results indicated that the morphology of the grains of coarse aggregate has an impact on the strength and stiffness properties of SCHPFRC. Moreover, significant differences in the transverse strain of concretes were observed. The morphology of the coarse aggregate also has an impact on the rheological parameters of a fresh concrete mixture. To better understand this phenomenon, the hypothesized mechanism of the formation of SCHPFRC caused by different morphology of coarse aggregate was proposed at the end of the article.

Sign in / Sign up

Export Citation Format

Share Document