scholarly journals A Mechanical Analysis of Chemically Stimulated Linear Shape Memory Polymer Actuation

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 481
Author(s):  
Hakan Dumlu ◽  
Axel Marquardt ◽  
Elias M. Zirdehi ◽  
Fathollah Varnik ◽  
Yucen Shen ◽  
...  
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Shape Memory Polymer ◽  
Mechanical Analysis ◽  
Micromechanical Modeling ◽  
Glass Temperature ◽  
Elementary Processes ◽  
Linear Shape

In the present work, we study the role of programming strain (50% and 100%), end loads (0, 0.5, 1.0, and 1.5 MPa), and chemical environments (acetone, ethanol, and water) on the exploitable stroke of linear shape memory polymer (SMP) actuators made from ESTANE ETE 75DT3 (SMP-E). Dynamic mechanical thermal analysis (DMTA) shows how the uptake of solvents results in a decrease in the glass temperature of the molecular switch component of SMP-E. A novel in situ technique allows studying chemically triggered shape recovery as a function of time. It is found that the velocity of actuation decreases in the order acetone > ethanol > water, while the exploitable strokes show the inverse tendency and increases in the order water > ethanol > acetone. The results are interpreted on the basis of the underlying chemical (how solvents affect thermophysical properties) and micromechanical processes (the phenomenological spring dashpot model of Lethersich type rationalizes the behavior). The study provides initial data which can be used for micromechanical modeling of chemically triggered actuation of SMPs. The results are discussed in the light of underlying chemical and mechanical elementary processes, and areas in need of further work are highlighted.

scholarly journals In Situ Generation of Green Hybrid Nanofibrillar Polymer-Polymer Composites—A Novel Approach to the Triple Shape Memory Polymer Formation

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1900
Author(s):  
Ramin Hosseinnezhad ◽  
Iurii Vozniak ◽  
Fahmi Zaïri
Keyword(s):  
Polymer Blends ◽  
Shape Memory ◽  
Shape Memory Polymer ◽  
Cellulose Nanofibers ◽  
Polymeric Materials ◽  
Novel Approach ◽  
Phase Transition Temperatures ◽  
Triple Shape Memory

The paper discusses the possibility of using in situ generated hybrid polymer-polymer nanocomposites as polymeric materials with triple shape memory, which, unlike conventional polymer blends with triple shape memory, are characterized by fully separated phase transition temperatures and strongest bonding between the polymer blends phase interfaces which are critical to the shape fixing and recovery. This was demonstrated using the three-component system polylactide/polybutylene adipateterephthalate/cellulose nanofibers (PLA/PBAT/CNFs). The role of in situ generated PBAT nanofibers and CNFs in the formation of efficient physical crosslinks at PLA-PBAT, PLA-CNF and PBAT-CNF interfaces and the effect of CNFs on the PBAT fibrillation and crystallization processes were elucidated. The in situ generated composites showed drastically higher values of strain recovery ratios, strain fixity ratios, faster recovery rate and better mechanical properties compared to the blend.

Actuation of Shape Memory Polymer by Resistive Heating of Carbon Nanopaper

2009 ◽  
Author(s):  
Haibao Lu ◽  
Yong Tang ◽  
Jihua Gou ◽  
Erin Chow ◽  
Jinsong Leng ◽  
...  
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Carbon Nanofiber ◽  
Volume Fraction ◽  
Shape Memory Polymer ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Paper Sheet ◽  
Scanning Electron ◽  
Properties Of Composites

To electrically activate the shape recovery in a styrene-based shape-memory polymer (SMP) by coating with conductive carbon nanofiber paper has been demonstrated in this paper. Carbon nanofibers in the form of paper sheet in combination with SMP significantly improve the electrical and thermal conductivity of polymer, leading to the actuation of SMP/nanopaper composite (with 15% volume fraction of carbon nanopaper, dimension of 10.0 cm × 0.5 cm × 0.3 cm) can be carried out by applying 8.4 V voltage, with response time of 140 s. Therefore, electrical conductivity of 6.6 S/cm is obtained. This approach, although demonstrated in styrene-based polymer, is applicable to other type of SMP materials. Furthermore, the morphologies of carbon nanofiber in the form of paper is observed by scanning electron microscopy, and the thermomechanical properties of composites are measured and analyzed by dynamic mechanical analysis.

Influence of Radialization Dosage on Shape Memory Effect of Polystyrene Copolymer

2008 ◽  
Vol 47-50 ◽  
pp. 690-693 ◽  
Author(s):  
Da Wei Zhang ◽  
Jin Song Leng ◽  
Yan Ju Liu
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Smart Materials ◽  
Shape Recovery ◽  
Memory Performance ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
Mechanical Analysis ◽  
Styrene Copolymer

This paper is concerned about the synthesis of shape memory styrene copolymer and the investigation of the influence of radialization dosage on its shape memory effect. As one of novel actuators in smart materials, shape memory polymers (SMPs) have been investigated intensively. Styrene copolymer with proper cross-linking degree can exhibit shape memory effect (SME). In this paper, the influence of radialization on shape memory effect of styrene copolymer was investigated through altering the dosage of radialization. The radialization dosage of styrene copolymer was determined by changed radicalization time. The glass transition temperature (Tg) of styrene copolymerwas measured by Dynamic Mechanical Analysis (DMA). The shape memory performance of styrene copolymer with different radiated dosage was also evaluated. Results indicated that the shape memory polymer (SMP) was synthesized successfully. The Tg increased from 60°C to 65°C followed by increasing the radialization dosage. Moreover, the SMP experienced good SME and the largest reversible strain of the SMP reached as high as 150%. When heating above Tg+30°C (different copolymers performed different Tg), the shape recovery speed of the copolymers increased with increasing the radialization dosage. However, the recovery speed decreased with increasing the radialization dosage at the same temperature of 95°C.

Role of Si in Improving the Shape Recovery of FeMnSiCrNi Shape Memory Alloys

2011 ◽  
Vol 42 (8) ◽  
pp. 2153-2165 ◽  
Author(s):  
Bikas C. Maji ◽  
Madangopal Krishnan ◽  
Gouthama ◽  
R. K. Ray
Keyword(s):  
Shape Memory Alloys ◽  
Shape Memory ◽  
Shape Recovery

Investigate of Electrical Conductivity of Shape-Memory Polymer Filled with Carbon Black

2008 ◽  
Vol 47-50 ◽  
pp. 714-717 ◽  
Author(s):  
Xin Lan ◽  
Jin Song Leng ◽  
Yan Ju Liu ◽  
Shan Yi Du
Keyword(s):  
Electrical Conductivity ◽  
Carbon Black ◽  
Shape Memory ◽  
Shape Recovery ◽  
Volume Fraction ◽  
Shape Memory Polymer ◽  
Recovery Process ◽  
Thermomechanical Properties ◽  
Electrically Conductive ◽  
New System

A new system of thermoset styrene-based shape-memory polymer (SMP) filled with carbon black (CB) is investigated. To realize the electroactive stimuli of SMP, the electrical conductivity of SMP filled with various amounts of CB is characterized. The percolation threshold of electrically conductive SMP filled with CB is about 3% (volume fraction of CB), which is much lower than many other electrically conductive polymers. When applying a voltage of 30V, the shape recovery process of SMP/CB(10 vol%) can be realized in about 100s. In addition, the thermomechanical properties are also characterized by differential scanning calorimetery (DSC).

scholarly journals Electrical actuation and shape recovery control of shape-memory polymer nanocomposites

2013 ◽  
Vol 4 (3) ◽  
pp. 167-178 ◽  
Author(s):  
Fei Liang ◽  
Robert Sivilli ◽  
Jihua Gou ◽  
Yunjun Xu ◽  
Bob Mabbott
Keyword(s):  
Shape Memory ◽  
Polymer Nanocomposites ◽  
Shape Recovery ◽  
Shape Memory Polymer ◽  
Electrical Actuation

scholarly journals Bio-Based Epoxy Shape-Memory Thermosets from Triglycidyl Phloroglucinol

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 542 ◽  
Author(s):  
David Santiago ◽  
Dailyn Guzmán ◽  
Francesc Ferrando ◽  
Àngels Serra ◽  
Silvia De la Flor
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Memory Performance ◽  
Crosslinking Agent ◽  
Shape Memory Polymers ◽  
Crosslinking Density ◽  
Mechanical Analysis ◽  
Diglycidyl Ether ◽  
Partial Substitution ◽  
Scanning Calorimetry

A series of bio-based epoxy shape-memory thermosetting polymers were synthesized starting from a triglycidyl phloroglucinol (3EPOPh) and trimethylolpropane triglycidyl ether (TPTE) as epoxy monomers and a polyetheramine (JEF) as crosslinking agent. The evolution of the curing process was studied by differential scanning calorimetry (DSC) and the materials obtained were characterized by means of DSC, thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), stress-strain tests, and microindentation. Shape-memory properties were evaluated under free and totally constrained conditions. All results were compared with an industrial epoxy thermoset prepared from standard diglycidyl ether of Bisphenol A (DGEBA). Results revealed that materials prepared from 3EPOPh were more reactive and showed a tighter network with higher crosslinking density and glass transition temperatures than the prepared from DGEBA. The partial substitution of 3EPOPh by TPTE as epoxy comonomer caused an increase in the molecular mobility of the materials but without worsening the thermal stability. The shape-memory polymers (SMPs) prepared from 3EPOPh showed good mechanical properties as well as an excellent shape-memory performance. They showed almost complete shape-recovery and shape-fixation, fast shape-recovery rates, and recovery stress up to 7 MPa. The results obtained in this study allow us to conclude that the triglycidyl phloroglucinol derivative of eugenol is a safe and environmentally friendly alternative to DGEBA for preparing thermosetting shape-memory polymers.

Sign in / Sign up

Export Citation Format

Share Document