diglycidyl ether
Recently Published Documents


TOTAL DOCUMENTS

1001
(FIVE YEARS 217)

H-INDEX

48
(FIVE YEARS 9)

2022 ◽  
Vol 1217 (1) ◽  
pp. 012017
Author(s):  
H Ghazali ◽  
K Ghazali ◽  
R Yusoff

Abstract In this study, microcapsules as potential candidates for self-healing agents were prepared by in situ polymerisation, taking place in oil-in-water emulsion. Poly(melamine-formaldehyde) is employed as shell material and diglycidyl ether of bisphenol A as polymerisable core materials and Pentaerythritol Tetrakis(3-Mercaptopropionate) as its hardener. The geometry, shell features, size distributions, core content, and the reactivity of the microcapsules were studied by scanning electron microscopy (SEM), optical microscopy (OM), Soxhlet extraction method and differential scanning calorimetry (DSC). Microcapsules with different sizes and distributions were obtained by adjusting the stirring speeds during the preparation stage. From the results, it was established that the spherical microcapsules fabricated using this technique, resulted in satisfactory size and shell structure with shell thickness of less than 2 μm. The microcapsules possess high core content at about 90 wt.% for each size range of microcapsules and it was also observed that the viscosity of the core content decreased at an elevated temperature. The results obtained in this work indicate that these microcapsules possess the characteristics that can be potentially used for self-healing applications.


Foods ◽  
2021 ◽  
Vol 10 (12) ◽  
pp. 3127
Author(s):  
Risi Wang ◽  
Ya Li ◽  
Xixiang Shuai ◽  
Jun Chen ◽  
Ruihong Liang ◽  
...  

Traditional aerogels lack specific functional groups for the adsorption of Pb2+, which results in a low adsorption capacity and limits the application scope. Novel porous pectin-based aerogels (PPEAs) were prepared by incorporating polyethylenimine (PEI) using ethylene glycol diglycidyl ether (EGDE) as a cross-linker for the removal of Pb2+ from water. The cross-linking mechanism, morphology, mechanical strength, thermal stability, adsorption properties, and mechanism of the aerogels were investigated. The aerogels possessed several desirable features, such as a large maximum Pb2+ adsorption capacity (373.7 mg/g, tested at pH 5.0), ultralight (as low as 63.4 mg/cm3), high mechanical strength (stress above 0.24 MPa at 50% strain), and easy recyclability. Meanwhile, the equilibrium adsorption data was well described by the Langmuir–Freundlich (Sips) model and the kinetic adsorption process was well fitted using the pseudo-second-order model. The donor groups, such as -NH2, and oxygen-containing functional groups were responsible for the Pb2+ adsorption, which was confirmed by the FTIR and XPS analysis. The excellent characteristics mean that PPEAs are highly effective adsorbents in the remediation of lead-containing wastewater.


Toxics ◽  
2021 ◽  
Vol 9 (12) ◽  
pp. 354
Author(s):  
Do-Hyun Kim ◽  
Jong-Hyeon Han ◽  
Hyuk-Cheol Kwon ◽  
Su-Jin Lim ◽  
Seo-Gu Han ◽  
...  

Poly(ethylene glycol) diglycidyl ether (PEGDE) is widely used to cross-link polymers, particularly in the pharmaceutical and biomaterial sectors. However, the subcutaneous toxicity of PEGDE has not yet been assessed. PEGDE samples (500–40,000 μg/mouse) were subcutaneously injected into the paraspinal dorsum of BALB/c male mice. Cage-side observations were carried out with measurement of organ weight, body weight variation, and feed intake, as well as histopathological characterization on day 28 post-exposure. Mice that received 40,000 μg of PEGDE showed severe toxic response and had to be euthanized. Subcutaneous injection of PEGDE did not alter feed intake and organ weight; however, the body weight variation of mice injected with 20,000 μg of PEGDE was significantly lower than that of the other groups. Exposure to 10,000 and 20,000 μg of PEGDE induced epidermal ulcer formation and hair loss. The histology of skin tissue in mice administered with 20,000 μg of PEGDE showed re-epithelialized or unhealed wounds. However, the liver, spleen, and kidneys were histologically normal. Collectively, PEGDE, particularly above 10,000 μg/mouse, caused subcutaneous toxicity with ulceration, but no toxicity in the other organs. These results may indicate the optimal concentration of subcutaneously injected PEGDE.


Polymers ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 4230
Author(s):  
Chung-Cheng Chang ◽  
Kwang-Ming Lee ◽  
Chia-Hong Huang

In this paper, it is reported that a metal-free and non-conjugated polymer, MA-PEG 8000-BADGE (MP8B), exhibits an antireflective property and substrate-dependent photoluminescence (SDP). MP8B was constructed from maleic anhydride, poly(ethylene glycol) and bisphenol-A diglycidyl ether. Self-assembled nanoparticles are found in MP8B and can prospectively act as scattering centers to improve light trapping and extraction. MP8B films prepared from MP8B solutions have been characterized by photoluminescence (PL), atomic force microscopy (AFM), tunnelling electron microscope (TEM), reflectance, transmittance, and UV-Vis absorption spectrum. MP8B films can suppress light reflection and enhance light transmission. The PL spectrum of MP8B film on ITO peaks at approximately 538 nm, spanning from 450 to 660 nm at a concentration of 25 mM. Meanwhile, the effects of concentration and substrate on the PL of MP8B films are also investigated in this study. Surface roughness becomes larger with concentration. A red shift of the PL spectrum is observed as solution concentration increases. Meanwhile, aggregation-caused quenching (ACQ) is insignificant. Moreover, the PL spectra of MP8B films show a substrate-dependent phenomenon due to dielectric screening. The optical band-gap energy of MP8B is approximately 4.05 eV. It is concluded that MP8B is a promising candidate for a host material, and its film can be utilized as a multifunctional layer (i.e., antireflective and light-scattering functions) for optoelectronic applications.


2021 ◽  
pp. 131491
Author(s):  
Michael J. Minkler ◽  
Xinyu Hou ◽  
Nima Alizadeh ◽  
Maria Auad ◽  
Anton Schindler ◽  
...  

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3914
Author(s):  
Florian Wanghofer ◽  
Archim Wolfberger ◽  
Markus Wolfahrt ◽  
Sandra Schlögl

Poly(ionic liquids) (PILs) and ionenes are polymers containing ionic groups in their repeating units. The unique properties of these polymers render them as interesting candidates for a variety of applications, such as gas separation membranes and polyelectrolytes. Due to the vast number of possible structures, numerous synthesis protocols to produce monomers with different functional groups for task-specific PILs are reported in literature. A difunctional epoxy-IL resin was synthesized and cured with multifunctional amine and anhydride hardeners and the thermal and thermomechanical properties of the networks were assessed via differential scanning calorimetry and dynamic mechanical analysis. By the selection of suitable hardeners, the glass transition onset temperature (Tg,onset) of the resulting networks was varied between 18 °C and 99 °C. Copolymerization of epoxy-IL with diglycidyl ether of bisphenol A (DGEBA) led to a further increase of the Tg,onset. The results demonstrate the potential of epoxy chemistry for tailorable PIL networks, where the hardener takes the place of the ligands without requiring an additional synthesis step and can be chosen from a broad range of commercially available compounds.


2021 ◽  
pp. 096739112110453
Author(s):  
Habibah Ghazali ◽  
Lin Ye ◽  
Amie N Amir

Among many applications, elevated-temperature cured epoxy resins are widely used for high-performance applications especially for structural adhesive and as a matrix for structural composites. This is due to their superior chemical and mechanical properties. The thermosetting nature of epoxy produces a highly cross-linked polymer network during the curing process where the resulting material exhibited excellent properties. However, due to this cross-linked molecular structure, epoxies are also known to be brittle, and once a crack initiated in the material, it is difficult to arrest the crack propagation. Earlier research found that the inclusion of encapsulated healing agents is able to introduce self-healing ability to the room-temperature cured epoxies. The current study investigated the self-healing behaviour of an elevated-temperature cured epoxy, which incorporated the dual-capsule system loaded with diglycidyl-ether of bisphenol-A (DGEBA) resin and mercaptan. The microcapsules were prepared by the in-situ polymerisation method while the fracture toughness and the self-healing capability of the tapered-double-cantilever-beam (TDCB) epoxy specimens were measured under Mode-I fracture toughness testing. We investigated the effect of temperature on viscosity of the healing agents and how these values influence the formation of uniform healing on the fracture surfaces. It was found that incorporation of the dual-capsule self-healing system onto an elevated-temperature cured epoxy slightly changed the fracture toughness of the epoxy as indicated by the Mode-I testing. In the case of thermal healing at 70°C, the self-healing epoxy exhibited a recovery of up to 111% of its original fracture toughness, where a uniform spreading of the healant was observed. The excellent healing behaviour is attributed to the lower viscosity of the healant at higher temperature and the higher glass transition temperature ( Tg) of the produced healant film. The DSC analysis confirmed that the healing process was not contributed by the post-curing of the host epoxy.


Sign in / Sign up

Export Citation Format

Share Document