scholarly journals Technological, Microstructural and Strength Aspects of Welding and Post-Weld Heat Treatment of Martensitic, Wear-Resistant Hardox 600 Steel

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4541
Author(s):  
Łukasz Konat
Keyword(s):  
Heat Treatment ◽  
Welded Joints ◽  
Base Material ◽  
High Strength ◽  
Carbon Equivalent ◽  
Plastic Properties ◽  
Entire Area ◽  
Welding Processes ◽  
Metallurgical Weldability ◽  
Structural Aspects

The study presents technological and structural aspects of production and heat treatment of welded joints of high-strength, abrasion-resistant Hardox 600 steel. As a result of the conducted research, it was found that the use of welding processes for joining this steel leads to the formation of a wide heat-affected zone, characterized by various structures favoring the reduction of abrasion resistance and deterioration of plastic properties, while increasing the susceptibility to brittle fracture. On the basis of the structural and strength characteristics, an effective welding technology for Hardox 600 steel was proposed, as well as the conditions and parameters of post-welding heat treatment, leading to obtaining structures close to a base material in the entire area of the welded joint. Despite the limited high-carbon equivalent CEV of the metallurgical weldability of the tested steel, the tests carried out in laboratory conditions allowed researchers to obtain welded joints characterized by very high strength indexes, corresponding to the base material, while maintaining satisfactory plastic and impact properties.

scholarly journals Structural Aspects of Execution and Thermal Treatment of Welded Joints of Hardox Extreme Steel

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 915 ◽  
Author(s):  
Konat
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Welded Joints ◽  
Base Material ◽  
Steel Structures ◽  
High Strength ◽  
Carbon Equivalent ◽  
Material Structure ◽  
Welding Processes ◽  
Structural Aspects

The paper presents structure and mechanical properties of welded joints of the high-strength, abrasive-wear resistant steel Hardox Extreme. It was shown that, as a result of welding this steel, structures conducive to lowering its abrasion-wear resistance are created in the heat-affected zone. Width of the zone exceeds 60 mm, which results in accelerated wear in the planned applications. On the grounds of the carried-out examinations of structures and selected mechanical properties, a welding technology followed by heat treatment of heat-affected zones was suggested, leading to reconstruction of HAZ structures that is morphologically close to the base material structure. In spite of high carbon equivalent (CEV) of Hardox Extreme, the executed welding processes and heat treatment did not result in the appearance, in laboratory conditions, of welding imperfections in the welded joints.

scholarly journals The Assessment of Selected Properties of Welded Joints in High-Strength Steels

2020 ◽  
pp. 73-79
Author(s):  
Lechosław Tuz
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Welded Joints ◽  
Heat Input ◽  
Structural Changes ◽  
High Strength Steels ◽  
High Strength ◽  
High Quality ◽  
Treatment Processes ◽  
Welding Processes

The use of technologically advanced structural materials entails the necessity of adjusting typical welding processes to special requirements resulting from the limited weldability of certain material groups. Difficulties obtaining high-quality joints may be the consequence of deteriorated mechanical properties and structural changes in materials (beyond requirements of related standards). One of the aforementioned materials is steel characterised by a guaranteed yield point of 1300 MPa, where high strength is obtained through the addition of slight amounts of carbide-forming elements and the application of complex heat treatment processes. A heat input during welding may worsen the aforesaid properties not only in the weld but also in the adjacent material. The tests discussed in the article revealed that the crucial area was that heated below a temperature of 600°C, where the hardness of the material decreased from approximately 520 HV to 330 HV.

Microstructure of resistance spot welding of maraging steels

1990 ◽  
Vol 48 (4) ◽  
pp. 900-901
Author(s):  
I. Neuman ◽  
S.F. Dirnfeld ◽  
I. Minkoff
Keyword(s):  
Maraging Steel ◽  
Spot Welding ◽  
Lath Martensite ◽  
Base Material ◽  
Aging Treatment ◽  
High Strength ◽  
Maraging Steels ◽  
Heat Treated ◽  
Current Cycle ◽  
Welding Processes

Experimental work on the spot welding of Maraging Steels revealed a surprisingly low level of strength - both in the as welded and in aged conditions. This appeared unusual since in the welding of these materials by other welding processes (TIG,MIG) the strength level is almost that of the base material. The maraging steel C250 investigated had the composition: 18wt%Ni, 8wt%Co, 5wt%Mo and additions of Al and Ti. It has a nominal tensile strength of 250 KSI. The heat treated structure of maraging steel is lath martensite the final high strength is reached by aging treatment at 485°C for 3-4 hours. During the aging process precipitation takes place of Ni3Mo and Ni3Ti and an ordered solid solution containing Co is formed.Three types of spot welding cycles were investigated: multi-pulse current cycle, bi-pulse cycle and single pulsle cycle. TIG welded samples were also tested for comparison.The microstructure investigations were carried out by SEM and EDS as well as by fractography. For multicycle spot welded maraging C250 (without aging), the dendrites start from the fusion line towards the nugget centre with an epitaxial growth region of various widths, as seen in Figure 1.

scholarly journals Development of laser welding of high strength aluminium alloy 2024-T4 with controlled thermal cycle

2020 ◽  
Vol 326 ◽  
pp. 08005
Author(s):  
Mete Demirorer ◽  
Wojciech Suder ◽  
Supriyo Ganguly ◽  
Simon Hogg ◽  
Hassam Naeem
Keyword(s):  
Laser Beam ◽  
Laser Welding ◽  
Heat Input ◽  
Thermal Cycle ◽  
Laser Beam Welding ◽  
Base Material ◽  
High Strength ◽  
Cooling Rates ◽  
Aa 2024 ◽  
Welding Processes

An innovative process design, to avoid thermal degradation during autogenous fusion welding of high strength AA 2024-T4 alloy, based on laser beam welding, is being developed. A series of instrumented laser welds in 2 mm thick AA 2024-T4 alloys were made with different processing conditions resulting in different thermal profiles and cooling rates. The welds were examined under SEM, TEM and LOM, and subjected to micro-hardness examination. This allowed us to understand the influence of cooling rate, peak temperature, and thermal cycle on the growth of precipitates, and related degradation in the weld and heat affected area, evident as softening. Although laser beam welding allows significant reduction of heat input, and higher cooling rates, as compared to other high heat input welding processes, this was found insufficient to completely supress coarsening of precipitate in HAZ. To understand the required range of thermal cycles, additional dilatometry tests were carried out using the same base material to understand the time-temperature relationship of precipitate formation. The results were used to design a novel laser welding process with enhanced cooling, such as with copper backing bar and cryogenic cooling.

Mechanical Behaviour of Welded Joints Achieved by Multi-Wire Submerged Arc Welding

2017 ◽  
Vol 1143 ◽  
pp. 52-57
Author(s):  
Elena Scutelnicu ◽  
Carmen Catalina Rusu ◽  
Bogdan Georgescu ◽  
Octavian Mircea ◽  
Melat Bormambet
Keyword(s):  
Mechanical Behaviour ◽  
Welded Joints ◽  
Arc Welding ◽  
Base Material ◽  
High Strength ◽  
Submerged Arc Welding ◽  
Steel Plates ◽  
Wire Saw ◽  
Api 5L X70 Steel ◽  
Submerged Arc

The paper addresses the development of advanced welding technologies with two and three solid wires for joining of HSLA API-5l X70 (High-strength low-alloy) steel plates with thickness of 19.1 mm. The experiments were performed using a multi-wire Submerged Arc Welding (SAW) system that was developed for welding of steels with solid, tubular and cold wires, in different combinations. The main goal of the research was to assess the mechanical performances of the welded joints achieved by multi-wire SAW technology and then to compare them with the single wire variant, as reference system. The welded samples were firstly subjected to NDT control by examinations with liquid penetrant, magnetic particle, ultrasonic and gamma radiation, with the aim of detecting the specimens with flaws and afterwards to reconsider and redesign the corresponding Welding Procedure Specifications (WPS). The defect-free welded samples were subjected to tensile, Charpy V-notch impact and bending testing in order to analyse and report the mechanical behaviour of API-5l X70 steel during multi-wire SAW process. The experimental results were processed and comparatively discussed. The challenge of the investigation was to find the appropriate welding technology which responds simultaneously to the criteria of quality and productivity. Further research on metallurgical behaviour of the base material will be developed, in order to conclude the complete image of the SAW process effects and to understand how the multi-wire technologies affect the mechanical and metallurgical characteristics of the API-5L X70 steel used in pipelines fabrication.

scholarly journals Assessment of the Effect of Laser Welding on the Properties and Structure of TMCP Steel Butt Joints

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1312 ◽  
Author(s):  
Jacek Górka
Keyword(s):  
Laser Beam ◽  
Welded Joints ◽  
Research Work ◽  
Laser Beam Welding ◽  
Welding Process ◽  
Tensile Tests ◽  
Carbon Equivalent ◽  
Quality Level ◽  
Butt Joints ◽  
Plastic Properties

The research work and related tests aimed to identify the effect of filler metal-free laser beam welding on the structure and properties of butt joints made of steel 700MC subjected to the TMCP (thermo-mechanically controlled processed) process. The tests involved 10-mm thick welded joints and a welding linear energy of 4 kJ/mm and 5 kJ/mm. The inert gas shielded welding process was performed in the flat position (PA) and horizontal position (PC). Non-destructive testing enabled classification of the tested welded joints as representing the quality level B in accordance with the requirements set out in standard 13919-1. Destructive tests revealed that the tensile strength of the joints was 5% lower than S700MC steel. The results of tensile tests and changes in structure were referred to joints made using the MAG (Metal Active Gas) method. The tests of thin films performed using a high-resolution scanning transmission electron microscope revealed that, during laser beam welding, an increase in dilution was accompanied by an increase in the content of alloying microadditions titanium and niobium, particularly in the fusion area. A significant content of hardening phases in the welded joint during cooling led to significant precipitation hardening by fine-dispersive (Ti,Nb)(C,N) type precipitates being of several nanometres in size, which, in turn, resulted in the reduction of plastic properties. An increase in the concentration of elements responsible for steel hardening, i.e., Ti and Nb, also contributed to reducing the weld toughness below the acceptable value, which amounts to 25 J/cm2. In cases of S700MC, the analysis of the phase transformation of austenite exposed to welding thermal cycles and the value of carbon equivalent cannot be the only factors taken into consideration when assessing weldability.

The heat treatment of welded joints in the flash welding of high strength casing pipes

1987 ◽  
Vol 1 (5) ◽  
pp. 426-431
Author(s):  
Yu V Skul'skii ◽  
A E Grabezhov ◽  
V G Vasol'ev ◽  
T A Kornienko ◽  
G I Nemirovskii
Keyword(s):  
Heat Treatment ◽  
Welded Joints ◽  
High Strength ◽  
Flash Welding
Sign in / Sign up

Export Citation Format

Share Document