scholarly journals Assessment of the Effect of Laser Welding on the Properties and Structure of TMCP Steel Butt Joints

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1312 ◽  
Author(s):  
Jacek Górka
Keyword(s):  
Laser Beam ◽  
Welded Joints ◽  
Research Work ◽  
Laser Beam Welding ◽  
Welding Process ◽  
Tensile Tests ◽  
Carbon Equivalent ◽  
Quality Level ◽  
Butt Joints ◽  
Plastic Properties

The research work and related tests aimed to identify the effect of filler metal-free laser beam welding on the structure and properties of butt joints made of steel 700MC subjected to the TMCP (thermo-mechanically controlled processed) process. The tests involved 10-mm thick welded joints and a welding linear energy of 4 kJ/mm and 5 kJ/mm. The inert gas shielded welding process was performed in the flat position (PA) and horizontal position (PC). Non-destructive testing enabled classification of the tested welded joints as representing the quality level B in accordance with the requirements set out in standard 13919-1. Destructive tests revealed that the tensile strength of the joints was 5% lower than S700MC steel. The results of tensile tests and changes in structure were referred to joints made using the MAG (Metal Active Gas) method. The tests of thin films performed using a high-resolution scanning transmission electron microscope revealed that, during laser beam welding, an increase in dilution was accompanied by an increase in the content of alloying microadditions titanium and niobium, particularly in the fusion area. A significant content of hardening phases in the welded joint during cooling led to significant precipitation hardening by fine-dispersive (Ti,Nb)(C,N) type precipitates being of several nanometres in size, which, in turn, resulted in the reduction of plastic properties. An increase in the concentration of elements responsible for steel hardening, i.e., Ti and Nb, also contributed to reducing the weld toughness below the acceptable value, which amounts to 25 J/cm2. In cases of S700MC, the analysis of the phase transformation of austenite exposed to welding thermal cycles and the value of carbon equivalent cannot be the only factors taken into consideration when assessing weldability.

scholarly journals Distortion Control for Dissimilar Welding of SS321 to Hastelloy C-276 with CO2 Laser Beam Butt Joints Using Taguchi Methods

2021 ◽  
Vol 8 (3) ◽  
pp. 461-466
Author(s):  
Gandu Guruvaiah Naidu ◽  
Sarojini Jajimoggala
Keyword(s):  
Laser Beam ◽  
Co2 Laser ◽  
Gas Flow ◽  
Laser Beam Welding ◽  
Welding Process ◽  
Taguchi Methods ◽  
Quality Characteristic ◽  
Dissimilar Welding ◽  
Bead Geometry ◽  
Butt Joints

The laser beam welding process is a promising technology because of its reliability and ability to automate the process easily. This study aims to analyze distortion for dissimilar laser weld joints. Hastelloy C276 and SS321 plates are joined by using the CO2 Laser beam welding. Welding current, welding speed and shielding gas flow are chosen as process parameters for preparing butt joints. Each of the factors has two levels to control the parameters of the output. Experimentation was conducted with four trails by using an L4 orthogonal array. The quality of the welds and bead geometry are verified through macrostructure examination. The Vernier height gauge was used for the measurement of distortion in the weldments. Lower the better-quality characteristic is chosen for the response. ANOVA studies identified laser power at 81%, the weld speed at 16% parameters is a contribution with a statistical of about 95%. Full penetration was observed for all the experimental trails.

scholarly journals Assessment of the Makeability of T-welded Joints in 10 mm Thick TMCP Steel Using Laser Beam

2018 ◽  
Author(s):  
Jacek Górka
Keyword(s):  
Laser Beam ◽  
Welded Joints ◽  
Base Material ◽  
Scanning Transmission Electron Microscope ◽  
High Yield ◽  
Deep Penetration ◽  
Quality Level ◽  
Plastic Properties ◽  
Thin Foils ◽  
Scanning Transmission

The article presents tests aimed to verify the possibility of making T-joints in TMCP steel using laser. The tests involved the use of 10 mm thick high yield point steel S700MC obtained in an industrial manufacturing process. The joints made in the tests were single and double-sided. Subsequent non-destructive tests revealed that the joints obtained in the tests represented quality level B in accordance with PN-EN ISO 13919-1. Single-sided welding performed using the laser beam having a power of 11 kW enabled the obtainment of 8 mm deep penetration without visibly deforming the web of the joint. The double-sided welded joints were characterised by proper geometry and the presence of gas pores in the welds not compromising the requirements of quality level B (strict requirements). The weld structure was bainitic-ferritic. The weld hardness was by approximately 60 HV1 higher than that of the base material (280 HV1). The HAZ area was slightly softer than the base material. The tests of thin foils performed using a high-resolution scanning transmission electron microscope revealed that, during welding, an increase in the content of the base material in the weld was accompanied by an increase in contents of alloying microagents Ti and Nb, particularly near the fusion line. The above-named alloying microagents, in the form of fine-dispersive (Ti,Nb)(C,N) type precipitates, could reduce plastic properties of joints.

scholarly journals Electron Beam Welding of TMCP steel S700MC

2020 ◽  
pp. 17-23
Author(s):  
Jacek Górka ◽  
Sylwester Błacha ◽  
Dawid Zagrobelny
Keyword(s):  
Electron Beam ◽  
Electron Beam Welding ◽  
Base Material ◽  
Welding Process ◽  
Tensile Tests ◽  
Quality Level ◽  
Plastic Properties ◽  
Hardness Tests ◽  
Static Tensile ◽  
Made In

The article discusses tests aimed to determine the effect of electron beam welding on the properties of butt welded joints made in 10 mm thick TMCP steel S700MC. The welding process was performed in the flat position (PA) using an XW150:30/756 welding and surface processing machine (Cambridge Vacuum Engineering). The joints obtained in the tests were subjected to non-destructive tests including visual tests and magnetic particle tests. The joints were also subjected to destructive tests including static tensile tests, bend tests, toughness tests (performed at a temperature of -30°C), hardness tests as well as macro and microscopic metallographic tests. The destructive tests revealed that the joint represented quality level B in accordance with the PN EN ISO 13919-1 standard. The analysis of the destructive test results related to the electron beam butt welded joint (made in steel S700MC) revealed its high mechanical and plastic properties. The toughness tests revealed a decrease in toughness in the HAZ (27 J/cm2) in comparison with that of the base material (50 J/cm2). In addition, the hardness of the HAZ and of the weld increased up to approximately 330 HV; the hardness of the base material amounted to 280 HV.

scholarly journals An Analysis of the Mechanical and Metallurgical Behavior of AISI 4130 Steel After Co2 Laser Beam Welding Process

2020 ◽  
Vol 9 (4) ◽  
pp. 2230-2234
Keyword(s):  
Laser Beam ◽  
Weld Joint ◽  
Focal Point ◽  
Focal Length ◽  
Research Work ◽  
Weld Zone ◽  
Laser Beam Welding ◽  
Welding Process ◽  
Bead Width ◽  
Aisi 4130

Alloy metal has received special attention in the aerospace and defense areas. The AISI 4130 alloy steel had been also considered, since it is applied in landing gears, small aircrafts engine cradles, and besides general industries. The Laser Beam Welding of high strength metals obtained small Weld Zone and better quality with good appearance. In this research work, a Laser Beam Welding (LBW) is used to weld AISI 4130. The experiments are conducted accordingly combination of Taguchi L25 based 5 levels of Laser Power, Speed, Angle, Focal Length and Focal Point Position. The AISI 4130 weld joint Bead Width and tensile strength are measured and analysed by ANOVA. Microstructure and SEM with EDAX are using to analysis the AISI 4130 weld joint.

scholarly journals Hybrid Welding (Laser–Electric Arc MAG) of High Yield Point Steel S960QL

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5447
Author(s):  
Michał Urbańczyk ◽  
Janusz Adamiec
Keyword(s):  
Welded Joints ◽  
Base Material ◽  
Welding Process ◽  
Electric Arc ◽  
Coarse Grained ◽  
High Yield ◽  
Quality Level ◽  
Hybrid Welding ◽  
Plastic Properties ◽  
Welding Thermal Cycle

The article discusses the effect of the hybrid-welding process (laser–electric arc MAG Metal Active Gas) on the structure and properties of butt joints (having various thicknesses, i.e., 5 mm and 7 mm) made of steel S960QL. Welding tests were performed in the flat position (PA) and in the horizontal position (PC). Joints made of steel S960QL in the above-presented configuration are present in elements of crane structures (e.g., telescopic crane jibs). The welding tests involved the use of the G Mn4Ni1.5CrMo solid electrode wire and the Ar+18% CO2 shielding gas mixture (M21) (used in the MAG method). Non-destructive visual and radiographic tests did not reveal the presence of any welding imperfections in the joints. The welded joints obtained in the tests represented quality level B in accordance with the requirements of the ISO 12932 standard. Microscopic metallographic tests revealed that the heat-affected zone (HAZ) contained the coarse-grained martensitic structure resulting from the effect of the complex welding thermal cycle on the microstructure of the joints. Destructive tests revealed that the joints were characterised by tensile strength similar to that of the base material. The hybrid welding (laser–MAG) of steel S960QL enabled the obtainment of joints characterised by favourable plastic properties and impact energy exceeding 27 J. The tests revealed the possibility of making hybrid-welded joints satisfying the quality-related requirements specified in the ISO 15614-14 standard.

scholarly journals Spectroscopic closed loop control of penetration depth in laser beam welding process

2012 ◽  
Author(s):  
Teresa Sibillano ◽  
Antonio Ancona ◽  
Domenico Rizzi ◽  
Francesco Mezzapesa ◽  
Ali Riza Konuk ◽  
...  
Keyword(s):  
Laser Beam ◽  
Penetration Depth ◽  
Closed Loop ◽  
Laser Beam Welding ◽  
Welding Process ◽  
Closed Loop Control ◽  
Loop Control
Sign in / Sign up

Export Citation Format

Share Document