scholarly journals Surface Roughness Analysis of H13 Steel during Electrical Discharge Machining Process Using Cu–TiC Sintered Electrode

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 5943
Author(s):  
Arminder Singh Walia ◽  
Vineet Srivastava ◽  
Mayank Garg ◽  
Nalin Somani ◽  
Nitin Kumar Gupta ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Electrical Discharge ◽  
Pulse Current ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
H13 Steel ◽  
Machined Surface ◽  
Machined Surface Quality ◽  
Semi Empirical

In electrical discharge machining (EDM), the machined surface quality can be affected by the excessive temperature generation during the machining process. To achieve a longer life of the finished part, the machined surface quality plays a key role in maintaining its overall integrity. Surface roughness is an important quality evaluation of a material’s surface that has considerable influence on mechanical performance of the material. Herein, a sintered cermet tooltip with 75% copper and 25% titanium carbide was used as tool electrode for processing H13 steel. The experiments have been performed to investigate the effects of EDM parameters on the machined surface roughness. The findings show that, as the pulse current, pulse length, and pulse interval are increased, the surface roughness tends to rise. The most significant determinant for surface roughness was found to be pulse current. A semi-empirical surface roughness model was created using the characteristics of the EDM technique. Buckingham’s theorem was used to develop a semi-empirical surface roughness prediction model. The semi-empirical model’s predictions were in good agreement with the experimental studies, and the built empirical model based on physical features of the cermet tooltip was tested using dimensional analysis.

Study on the improvement of the surface integrity and efficiency of electrical-discharge-machined TC4 titanium alloy via abrasive flow machining

2020 ◽  
pp. 095440542097109
Author(s):  
Ze Yu ◽  
Dunwen Zuo ◽  
Yuli Sun ◽  
Guohua Li ◽  
Xuemei Chen ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Surface Quality ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Small Hole ◽  
Machining Process ◽  
Machining Efficiency ◽  
Abrasive Flow Machining ◽  
Tc4 Titanium Alloy

To simultaneously optimize the surface quality and machining efficiency of the electrical discharge machining (EDM) processes used to produce titanium alloy quadrilateral group small hole parts, a combined “EDM + AFM” machining technology is proposed in this paper as an efficient and high-quality machining approach. In the proposed method, TC4 titanium alloy is first machined using the EDM process with graphite electrodes and the abrasive flow machining (AFM) process is then used to finish the machined surface. The effects of various electrical parameters on EDM-derived surface quality and improvements in EDM-derived quality under the application of AFM were assessed and, using the final surface roughness as a constraint condition, the effects of various combinations of EDM and “EDM + AFM” on efficiency were studied. The results revealed that the thickness and surface roughness of the superficial recast layer of the TC4 titanium alloy increase with both current and pulse width; in particular, increasing these parameters can increase the surface roughness by two to three grades. Following AFM, the alloy has a more uniform hardness distribution and the surface stress state changes from tensile to compressive stress, indicating that the combined “EDM + AFM” machining scheme can significantly enhance the surface quality of EDM-produced titanium alloy quadrilateral small group holes. The combined scheme achieves a balancing point beyond which increasing the roughness or the number of machining holes enhances either the machining efficiency or the machining surface quality. In the case of typical titanium alloy quadrilateral group small hole parts, the combined machining process can improve the finishing efficiency and total machining efficiency by 71.2% and 25.36%, respectively.

scholarly journals 302 Evaluation of Machined Surface Quality of Long Fiber FRM by Electrical Discharge Machining

2000 ◽  
Vol 2000.53 (0) ◽  
pp. 49-50
Author(s):  
Rikio HIKIJI ◽  
Yoshihiro KAWANO ◽  
Koji ABURADA ◽  
Masakazu HARADA ◽  
Minoru ARAI
Keyword(s):  
Surface Quality ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machined Surface ◽  
Machined Surface Quality

Surface Study in a Non-conventional (Electrical Discharge Machining) Process for Grade 6 Titanium Material

2014 ◽  
Vol 68 (1) ◽  
Author(s):  
Md. Ashikur Rahman Khan ◽  
M. M. Rahman
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Machined Surface ◽  
Titanium Material ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

Electrical discharge machining (EDM) produces complex shapes and permits high-precision machining of any hard or difficult-to-cut materials. The performance characteristics such as surface roughness and microstructure of the machined face are influenced by numerous parameters. The selection of parameters becomes complicated. Thus, the surface roughness (Ra) and microstructure of the machined surface in EDM on Grade 6 titanium alloy are studied is this study. The experimental work is performed using copper as electrode material. The polarity of the electrode is maintained as negative. The process parameters taken into account in this study are peak current (Ip), pulse-on time (Ton), pulse-off time (Toff), and servo-voltage (Sv). A smooth surface finish is found at low pulse current, small on-time and high off-time. The servo-voltage affects the roughness diversely however, a finish surface is found at 80 V Sv. Craters, cracks and globules of debris are appeared in the microstructure of the machined part. The size and degree of craters as well as cracks increase with increasing in energy level. Low discharge energy yields an even surface. This approach helps in selecting proper process parameters resulting in economic EDM machining. 

Surface Morphology and Corrosion Behavior in Nano PMEDM

2016 ◽  
Vol 724 ◽  
pp. 61-65 ◽  
Author(s):  
Ahmad Majdi Abdul-Rani ◽  
Alexis Mouangue Nanimina ◽  
Turnad Lenggo Ginta
Keyword(s):  
Titanium Alloy ◽  
Corrosion Rate ◽  
Surface Morphology ◽  
Surface Quality ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Application Process ◽  
Machined Surface ◽  
Conventional Machining

This research study was conducted to investigate the effect of nanoaluminum powder mixed electrical discharge machining (PMEDM) on surface morphology and corrosion rate of titanium alloy material. The development of devices such as implants in biomedical engineering application nowadays requires materials having good mechanical and physical properties. Conventional machining process of titanium as implant is a challenge resulting relative poor surface quality. Even using electrical discharge machining (EDM) which is non-conventional machining process there are limitations including machined surface alteration with relative poor machined surface quality, low corrosion resistance and. PMEDM is hypothesized to address the above mentioned problems. In this study, PMEDM on titanium alloy using nanoaluminum powder and copper-tungsten electrode was assessed to investigate the improvement for implant application. Process parameters used are peak-current, ON-time, gap voltage and powder concentration. Surface morphology and average corrosion arte are selected output responses. Results showed that Surface morphology of PMEDM machined surface is significantly improved. PMEDM marginally enhanced corrosion rate of biomedical grade titanium alloy.

scholarly journals Surface Analysis of Wire-Electrical-Discharge-Machining-Processed Shape-Memory Alloys

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 530 ◽  
Author(s):  
Rakesh Chaudhari ◽  
Jay J. Vora ◽  
Vivek Patel ◽  
L. N. López de Lacalle ◽  
D. M. Parikh
Keyword(s):  
Surface Roughness ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Surface Integrity ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Wire Electrical Discharge Machining ◽  
Machined Surface ◽  
Edx Analysis

Shape-memory alloys such as nitinol are gaining popularity as advanced materials in the aerospace, medical, and automobile sectors. However, nitinol is a difficult-to-cut material because of its versatile specific properties such as the shape-memory effect, superelasticity, high specific strength, high wear and corrosion resistance, and severe strain hardening. Anunconventional machining process like wire-electrical-discharge-machining (WEDM) can be effectively and efficiently used for the machining of such alloys, although the WEDM-induced surface integrity of nitinol hassignificant impact on material performance. Therefore, this work investigated the surface integrity of WEDM-processed nitinol samples using digital microscopy imaging, scanning electron microscopy (SEM), and energy-dispersive X-ray (EDX) analysis. Three-dimensional analysis of the surfaces was carried out in two different patterns (along the periphery and the vertical plane of the machined surface) andrevealed that surface roughness was maximalat the point where the surface was largely exposed to the WEDM dielectric fluid. To attain the desired surface roughness, appropriate discharge energy is required that, in turn, requires the appropriate parameter settings of the WEDM process. Different SEM image analyses showed a reduction in microcracks and pores, and in globule-density size at optimized parameters. EDX analysis revealed the absence of wire material on the machined surface

scholarly journals Electrical Discharge Machining with SiC Powder-Mixed Dielectric: An Effective Application in the Machining Process of Hardened 90CrSi Steel

Machines ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 36 ◽  
Author(s):  
Thi-Hong Tran ◽  
Manh-Cuong Nguyen ◽  
Anh-Tung Luu ◽  
The-Vinh Do ◽  
Thu-Quy Le ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Pulse Current ◽  
Electrical Discharge Machining ◽  
Machining Process ◽  
Powder Concentration ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Edm Process

As a successful solution applied to electrical discharge machining (EDM), powder-mixed electrical discharge machining (PMEDM) has been proposed as an upgrade of the EDM process. The optimization of the process parameters of PMEDM is essential and pressing. In this study, Taguchi methods and analysis of variance (ANOVA) were used to find the main parameters affecting surface roughness in the EDM process with SiC powder-mixed-dielectric of hardened 90CrSi steel. The PMEDM parameters selected were the powder concentration, the pulse-on-time, the pulse-off-time, the pulse current, and the server voltage. It was found that SiC powder exhibits positive effects on reducing surface roughness. The roughness obtained with the optimum powder concentration of 4 g/L was reduced by 30.02% compared to that when processed by conventional EDM. Furthermore, the pulse-off-time was found to be the most influential factor that gave an important effect on surface roughness followed by the powder concentration. The EDM condition including a powder concentration of 4 g/L, a pulse-on-time of 6 µs, a pulse-off-time of 21 µs, a pulse current of 8 A, and a server voltage of 4 V resulted in the best surface roughness.

Gas-Liquid Combined Multiple Cut in High-Speed WEDM

2010 ◽  
Vol 97-101 ◽  
pp. 4168-4171
Author(s):  
Tong Wang ◽  
Yu Mei Lu ◽  
Xian Chong Lu ◽  
Sun Fei Wang ◽  
Jing Zhe
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
High Speed ◽  
Electrical Discharge Machining ◽  
Wire Electrode ◽  
Machined Surface ◽  
Machined Surface Quality ◽  
New Process ◽  
Dry And Wet Conditions ◽  
Discharge Gap

This paper investigates a new process of wire electrical discharge machining (WEDM) as gas-liquid combined multiple cut. High-speed WEDM (HS-WEDM) finishing was compared in atmosphere and emulsion. Dry finishing has shorter discharge gap, better straightness and surface roughness and much higher material MRR than that in emulsion. Influences of wire winding speed and no load worktable feed on machined surface quality in dry and wet conditions were discussed. The better straightness obtained in gas is explained by analyzing forces acting on wire electrode. When first cut and second cut were performed both in emulsion liquid, and third cut was done in atmosphere, the surface roughness is improved compared with conventional WEDM.

Sign in / Sign up

Export Citation Format

Share Document