scholarly journals Effect of Pre-Oxidation Treatment of Nano-SiC Particulates on Microstructure and Mechanical Properties of SiC/Mg-8Al-1Sn Composites Fabricated by Powder Metallurgy Combined with Hot Extrusion

Materials ◽  
2016 ◽  
Vol 9 (12) ◽  
pp. 964 ◽  
Author(s):  
Chuan-Peng Li ◽  
Zhi-Guo Wang ◽  
Min Zha ◽  
Cheng Wang ◽  
Hong-Chen Yu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Hot Extrusion ◽  
Oxidation Treatment ◽  
Microstructure And Mechanical Properties ◽  
Sic Particulates

Microstructural Evolution and Mechanical Properties of AZ91 and SiCp/AZ91 Magnesium Alloys upon Rapid Solidification/Powder Metallurgy Followed by Hot Extrusion

2010 ◽  
Vol 146-147 ◽  
pp. 734-737
Author(s):  
Hui Yu ◽  
Hua Shun Yu ◽  
Zhen Ya Zhang ◽  
Guang Hui Min ◽  
Cheng Chen
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Magnesium Alloys ◽  
Rapid Solidification ◽  
Microstructural Evolution ◽  
Hot Extrusion ◽  
Interface Debonding ◽  
Porosity Level ◽  
Az91 Magnesium ◽  
Sic Particulates

In this study, AZ91 and SiC particulates reinforced AZ91 (SiCp/AZ91) magnesium alloys were successfully fabricated using rapid solidification/powder metallurgy technique followed by hot extrusion. Microstructural evolution and mechanical properties of the monolithic AZ91 and SiCp/AZ91 magnesium alloys were evaluated. SiC particulates were well distributed with only few agglomerated particles. The porosity level and microhardness increased as SiCp content increased because the increased surface area of SiCp, harder ceramic phases and SiCp acted obstacles to the motion of dislocations. In addition, an increase in particulate reinforcement content was observed to decrease mechanical properties of the composite compared with the unreinforced counterpart due to increasing agglomerating regions and porosity, brittle interface debonding between matrix and SiCp.

Effect of Processing Methodology on Microstructure and Mechanical Properties of Sn-3.5Ag Solder

2008 ◽  
Author(s):  
P. Babaghorbani ◽  
M. Gupta
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Microwave Sintering ◽  
Hot Extrusion ◽  
Microstructure And Mechanical Properties ◽  
Manufacturing Techniques

The manufacturing techniques of powder metallurgy and casting were used to synthesize a Sn-3.5Ag followed by hot extrusion. In the sintering step of powder metallurgy, two routes of conventional and microwave sintering were investigated. Physical, microstructural, thermomechanical and mechanical properties of the developed solders were examined. These studies revealed that the best combination of the properties is realized from the Sn-3.5Ag synthesized using powder metallurgy incorporating microwave sintering route. An attempt is made to correlate processing-microstructure-properties relationship for Sn-3.5Ag.

scholarly journals Microstructure and mechanical properties of solid state recycled 4Cr5MoSiV (H11) steel prepared by powder metallurgy

2021 ◽  
pp. 100184
Author(s):  
Gyanendra Bhatta ◽  
Luis De Los Santos Valladares ◽  
Xinggang Liu ◽  
Zhaojun Ma ◽  
A. Bustamante Domínguez ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Solid State ◽  
Microstructure And Mechanical Properties

scholarly journals Microstructure and Mechanical Properties of Al2024 Alloy Modified with Mg and Zn Additions after Hot-Extrusion and Aging Processes

2016 ◽  
Vol 22 (S3) ◽  
pp. 1990-1991
Author(s):  
C.G. Garay-Reyes ◽  
M. A. Ruiz-Esparza-Rodríguez ◽  
E. Cuadros-Lugo ◽  
H. M. Medrano-Prieto ◽  
I. Estrada-Guel ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Hot Extrusion ◽  
Microstructure And Mechanical Properties ◽  
Al2024 Alloy

scholarly journals Study on Microstructure and Mechanical Properties of Al7068 Reinforced with Silicon Carbide and Fly Ash by Powder Metallurgy

2021 ◽  
Vol 7 (09) ◽  
pp. 47-53
Author(s):  
Md Mehtab Alam and B.S Motgi
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Fly Ash ◽  
Powder Metallurgy ◽  
Aluminum Matrix ◽  
Hydraulic Press ◽  
Powder Form ◽  
X Ray ◽  
Microstructure And Mechanical Properties ◽  
Scanning Electron

The paper deals with detailed study on microstructure and mechanical properties of aluminum 7068 reinforced with fly ash and silicon carbide by powder metallurgy, aluminum 7068, silicon carbide and fly ash were taken in powder form of required size and mixed together in varying proportion according to specification and compacted with pressure of 400MPa using hydraulic press to make samples and then samples were sintered at 600°c for 2 hours, the samples were tested for density, compressive strength, hardness and microstructure was analyzed using scanning electron microscope, energy dispersive x-ray study was carried out in order to confirm presence of silicon carbide and fly ash in aluminum matrix.

Sign in / Sign up

Export Citation Format

Share Document