scholarly journals Effect of the Hot Deformation Conditions on Structure and Mechanical Properties of AlCr/AlCrSi Powder Composites

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1853
Author(s):  
Elena N. Korosteleva ◽  
Gennady A. Pribytkov ◽  
Victoria V. Korzhova
Keyword(s):  
Mechanical Properties ◽  
Hot Deformation ◽  
Volume Growth ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
High Porosity ◽  
Matrix Composites ◽  
Powder Mixtures ◽  
Study Results ◽  
Al Matrix

Aluminum matrix composites usually contain strengthening particles of refractory compounds (SiC, Al2O3) that do not react with the Al matrix. There is a problem in producing the Al matrix composite with inclusion of metals that can generate intermetallic compounds with aluminum. In this case, a conventional sintering of powder mixtures results in high porosity due to volume growth. That is why some new methods of producing dense Al matrix composites are required. A possibility to create a dense powder Al-based composite containing hard components, such as chromium and silicon, without using the sintering process, is considered. This paper presents study results of structural and mechanical properties of Al-Cr and Al-Cr-Si composites produced by hot compaction of powder mixtures. An analysis of the relationship between mechanical properties and structures of Al-Cr and Al-Cr-Si composites is carried out. Optimal values for thermomechanical processing modes that ensure sufficient strength and plasticity are determined. It is shown that strong bonding of the aluminum particles occurs under hot deformation, and an aluminum matrix is formed that provides acceptable composite bending strength as a result. The presence of chromium and silicon hard inclusions is not a significant obstacle for aluminum plastic flow. Al-Cr and Al-Cr-Si composites produced by hot deformation of the powder mixtures can be used as cathode material for the deposition of wear-resistant nitride coatings on metalworking tools.

Effect of Titanium Carbide Particles on Mechanical Properties of Aluminum Matrix Composites

2017 ◽  
Vol 5 (2) ◽  
pp. 20-30
Author(s):  
Zaman Khalil Ibrahim
Keyword(s):  
Mechanical Properties ◽  
Titanium Carbide ◽  
Compression Strength ◽  
Volume Fraction ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Powder Metallurgy Technique ◽  
Carbide Particles ◽  
Properties Of Composites

In this research aluminum matrix composites (AMCs) was reinforced by titanium carbide (TiC) particles and was produced. Powder metallurgy technique (PM) has been used to fabricate AMCs reinforced with various amounts (0%, 4%, 8%, 12%, 16% and 20% volume fraction) of TiC particles to study the effect of different volume fractions on mechanical properties of the Al-TiC composites. Measurements of compression strength and hardness showed that mechanical properties of composites increased with an increase in volume fraction of TiC Particles. Al-20 % vol. TiC composites exhibited the best properties with hardness value (97HRB) and compression strength value (275Mpa).

Production of Al Metal Matrix Composites by the Stir-Casting Method

2013 ◽  
Vol 592-593 ◽  
pp. 614-617 ◽  
Author(s):  
Konstantinos Anthymidis ◽  
Kostas David ◽  
Pavlos Agrianidis ◽  
Afroditi Trakali
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Automobile Industry ◽  
Metal Matrix ◽  
Aluminum Matrix ◽  
Stir Casting ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Casting Method ◽  
Alloy Matrix

It is well known that the addition of ceramic phases in an alloy e.g. aluminum, in form of fibers or particles influences its mechanical properties. This leads to a new generation of materials, which are called metal matrix composites (MMCs). They have found a lot of application during the last twenty-five years due to their low density, high strength and toughness, good fatigue and wear resistance. Aluminum matrix composites reinforced by ceramic particles are well known for their good thermophysical and mechanical properties. As a result, during the last years, there has been a considerable interest in using aluminum metal matrix composites in the automobile industry. Automobile industry use aluminum alloy matrix composites reinforced with SiC or Al2O3 particles for the production of pistons, brake rotors, calipers and liners. However, no reference could be cited in the international literature concerning aluminum reinforced with TiB particles and Fe and Cr, although these composites are very promising for improving the mechanical properties of this metal without significantly alter its corrosion behavior. Several processing techniques have been developed for the production of reinforced aluminum alloys. This paper is concerned with the study of TiB, Fe and Cr reinforced aluminum produced by the stir-casting method.

Sign in / Sign up

Export Citation Format

Share Document