scholarly journals Microstructure and Properties of Spot Welded Joints of Hot-Stamped Ultra-High Strength Steel Used for Automotive Body Structures

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 285 ◽  
Author(s):  
Zhixia Qiao ◽  
Huijun Li ◽  
Lianjin Li ◽  
Xiaoyu Ran ◽  
Liwen Feng
Keyword(s):  
Spot Welding ◽  
Mechanical Performance ◽  
High Strength Steels ◽  
High Hardness ◽  
High Strength ◽  
Resistance Spot ◽  
Automotive Body ◽  
Ultra High Strength Steels ◽  
Structural Parts ◽  
Spot Welded

Hot-stamped ultra-high strength steels have been widely used in automobile structural parts. Considering the high splash tendency in resistance spot welding due to their extremely high hardness, in this work, microstructural characteristics and mechanical performance of the resistance spot welded ultra-high strength steels are investigated. The results indicate that the interface between the nugget and heat-affected zone (HAZ) is the weakest zone where fractures initiate. In tensile shearing tests, a qualified spot welding joint failed with a button-shaped fracture. Welding defects would significantly decrease the load-carrying capacity and lead to interfacial fracture, except for a button-shaped fracture. In spot welding, it was found that a specific mid-frequency alternating current (AC) input mode, in which a 6 ms cooling cycle was inserted between every two neighboring current pulses, can avoid the splash in the spot welding of hot-stamped hardened steels.

Resistance Spot Weldability of Hot-Formed Ultra High Strength Steel Based on Virtual and Physical Experiment

2015 ◽  
Vol 750 ◽  
pp. 244-250 ◽  
Author(s):  
Zhi Shui Yu ◽  
Wan Peng Dong ◽  
Chun Wei Ma ◽  
Jiang Wei Ren ◽  
Bi Hao Li ◽  
...  
Keyword(s):  
Spot Welding ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Investigations ◽  
Tensile Shear ◽  
Resistance Spot ◽  
Ultra High Strength Steel ◽  
Ultra High Strength Steels ◽  
Cross Tension ◽  
Good Agreement

In this study, virtual and physical experimental investigations were performed on the resistance spot weldability of hot-formed ultra high strength steels (UHSS). The sheets were joined by the resistance spot welding as lap or cross joint. The mechanical properties were assessed in terms of cross tension strength (CTS) and tensile shear strength (TSS). The micro structural profile and weld nugget diameter were also investigated. Both virtual and physical methods yielding results are in good agreement. The results are discussed in the light of earlier work published in the literature and contribute to a better understanding on the evaluation of resistance spot weldability.

scholarly journals Microstructure and Mechanical Performance of Resistance Spot Welded Martensitic Advanced High Strength Steel

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1021
Author(s):  
Yunzhao Li ◽  
Huaping Tang ◽  
Ruilin Lai
Keyword(s):  
Mechanical Properties ◽  
Failure Modes ◽  
Mechanical Performance ◽  
Strong Dependence ◽  
High Strength ◽  
Weld Nugget ◽  
Resistance Spot ◽  
Pull Out ◽  
Cross Tension ◽  
Spot Welded

Resistance spot welded 1.2 mm (t)-thick 1400 MPa martensitic steel (MS1400) samples are fabricated and their microstructure, mechanical properties are investigated thoroughly. The mechanical performance and failure modes exhibit a strong dependence on weld-nugget size. The pull-out failure mode for MS1400 steel resistance spot welds does not follow the conventional weld-nugget size recommendation criteria of 4t0.5. Significant softening was observed due to dual phase microstructure of ferrite and martensite in the inter-critical heat affected zone (HAZ) and tempered martensite (TM) structure in sub-critical HAZ. However, the upper-critical HAZ exhibits obvious higher hardness than the nugget zone (NZ). In addition, the mechanical properties show that the cross-tension strength (CTS) is about one quarter of the tension-shear strength (TSS) of MS1400 weld joints, whilst the absorbed energy of cross-tension and tension-shear are almost identical.

Expulsion Intensity Monitoring and Modeling in Resistance Spot Welding Based on Electrode Displacement Signals

2020 ◽  
Author(s):  
Yu-Jun Xia ◽  
Yan Shen ◽  
Lang Zhou ◽  
Yong-Bing Li
Keyword(s):  
Resistance Spot Welding ◽  
Spot Welding ◽  
Low Carbon Steel ◽  
Sheet Thickness ◽  
High Strength Steels ◽  
High Strength ◽  
Material Strength ◽  
Low Carbon ◽  
Resistance Spot ◽  
Electrode Displacement

Abstract Weld expulsion is one of the most common welding defects during resistance spot welding (RSW) process especially for high strength steels (HSS). In order to control and eventually eliminate weld expulsion in production, accurate assessment of the expulsion severity should be the first step and is urgently required. Among the existing methods, real-time monitoring of RSW-related process signals has become a promising approach to actualize the online evaluation of weld expulsion. However, the inherent correlation between the process signals and the expulsion intensity is still unclear. In this work, a commonly used process signal, namely the electrode displacement and its instantaneous behavior when expulsion occurs are systematically studied. Based upon experiments with various electrodes and workpieces, a nonlinear relation between the weight of expelled metal and the sudden displacement drop accompanied by the occurrence of weld expulsion is observed, which is mainly influenced by electrode tip geometry but not by material strength or sheet thickness. The intrinsic relationship between this specific signal feature and the magnitude of expulsion is further explored through geometrical analysis, and a modified analytical model for online expulsion evaluation is finally proposed. It is shown that the improved model could be applied to domed electrodes with different tip geometries and varying workpieces ranging from low carbon steel to HSS. The error of expulsion estimation could be limited within ±20.4 mg (±2σ) at a 95% confidence level. This study may contribute to the online control of weld expulsion to the minimum level.

scholarly journals Liquid Metal Embrittlement of Galvanized TRIP Steels in Resistance Spot Welding

Metals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 787 ◽  
Author(s):  
Wook-Sang Jeon ◽  
Ashutosh Sharma ◽  
Jae Pil Jung
Keyword(s):  
Liquid Metal ◽  
Resistance Spot Welding ◽  
Spot Welding ◽  
High Strength Steels ◽  
High Strength ◽  
Liquid Metal Embrittlement ◽  
Surface Cracks ◽  
Resistance Spot ◽  
Research Activities ◽  
Microscopic Features

Liquid metal embrittlement (LME) in Zn-coated steels is a serious issue in automotive design. The risk of rising LME surface cracks in resistance spot welding (RSW) of Zn-coated high strength steels has triggered significant research activities across the globe. This paper presents a state-of-the-art review of the various phenomena and issues related to LME during RSW. Various aspects of LME surface cracks have been described in this review, focusing on the macro- and microscopic features of LME, spot weld cracks, the sensitivity of the LME cracks towards surface locations, welding conditions, and susceptibility to high strength and galvanized steels. We also focus on the effects of various processing factors, such as temperature, stress, microstructure, and the nature of the galvanized layer, related to studies with actual spot welds LME cracks. Finally, we summarize the possible mechanisms of embrittlement and the remedies for minimizing LME cracks, with suitable guidelines to suppress surface cracks during RSW.

Sign in / Sign up

Export Citation Format

Share Document