scholarly journals Microstructure and Mechanical Performance of Resistance Spot Welded Martensitic Advanced High Strength Steel

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1021
Author(s):  
Yunzhao Li ◽  
Huaping Tang ◽  
Ruilin Lai
Keyword(s):  
Mechanical Properties ◽  
Failure Modes ◽  
Mechanical Performance ◽  
Strong Dependence ◽  
High Strength ◽  
Weld Nugget ◽  
Resistance Spot ◽  
Pull Out ◽  
Cross Tension ◽  
Spot Welded

Resistance spot welded 1.2 mm (t)-thick 1400 MPa martensitic steel (MS1400) samples are fabricated and their microstructure, mechanical properties are investigated thoroughly. The mechanical performance and failure modes exhibit a strong dependence on weld-nugget size. The pull-out failure mode for MS1400 steel resistance spot welds does not follow the conventional weld-nugget size recommendation criteria of 4t0.5. Significant softening was observed due to dual phase microstructure of ferrite and martensite in the inter-critical heat affected zone (HAZ) and tempered martensite (TM) structure in sub-critical HAZ. However, the upper-critical HAZ exhibits obvious higher hardness than the nugget zone (NZ). In addition, the mechanical properties show that the cross-tension strength (CTS) is about one quarter of the tension-shear strength (TSS) of MS1400 weld joints, whilst the absorbed energy of cross-tension and tension-shear are almost identical.

scholarly journals Effect of weld nugget size on failure mode and mechanical properties of microscale resistance spot welds on Ti–1Al–1Mn ultrathin foils

2018 ◽  
Vol 10 (7) ◽  
pp. 168781401878528 ◽  
Author(s):  
Feng Chen ◽  
Shiding Sun ◽  
Zhenwu Ma ◽  
GQ Tong ◽  
Xiang Huang
Keyword(s):  
Mechanical Properties ◽  
Failure Mode ◽  
Failure Modes ◽  
Mechanical Performance ◽  
Weld Nugget ◽  
Interfacial Failure ◽  
Spot Welds ◽  
Resistance Spot ◽  
Resistance Spot Welds ◽  
Pullout Failure

We use tensile–shear tests to investigate the failure modes of Ti–1Al–1Mn microscale resistance spot welds and to determine how the failure mode affects the microstructure, microhardness profile, and mechanical performance. Two different failure modes were revealed: interfacial failure mode and pullout failure mode. The welds that fail by pullout failure mode have much better mechanical properties than those that fail by interfacial failure mode. The results show that weld nugget size is also a principal factor that determines the failure mode of microscale resistance spot welds. A minimum weld nugget size exists above which all specimens fail by pullout failure mode. However, the critical weld nugget sizes calculated using the existing recommendations are not consistent with the present experimental results. We propose instead a modified model based on distortion energy theory to ensure pullout failure. Calculating the critical weld nugget size using this model provides results that are consistent with the experimental data to high accuracy.

scholarly journals Analysis of Fracture Modes of Resistance Spot Welded Hot-Stamped Boron Steel

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 764 ◽  
Author(s):  
Yixi Zhao ◽  
Yansong Zhang ◽  
Xinmin Lai
Keyword(s):  
Transition Zone ◽  
Base Material ◽  
High Strength ◽  
Boron Steel ◽  
Delta Ferrite ◽  
Fracture Modes ◽  
Resistance Spot ◽  
Pull Out ◽  
Lap Shear ◽  
Spot Welded

Fracture modes of resistance spot welded ultra-high strength hot-stamped boron steel via lap-shear test are different from that of the traditional advanced high strength steel due to the difference in geometrical size and material property of the spot welds. In this paper, lap-shear fracture modes of resistance spot welding joints were analyzed and joint characteristics that affecting the fracture behavior were discussed. Three fracture modes were found to change from interfacial fracture (IF) to pull-out fracture (PF) with the increase of nugget diameter. For PF I mode, the fracture initiated at the transition zone between the fusion zone and upper-critical heat affected zone (HAZ) and propagated along the thickness of the nugget. For PF II mode, during which the failure initiated at the sub-critical HAZ where the softest zone occurred, and it propagated to the base material. Obvious hardness decrease was observed in the transition zone with the formation of the delta ferrite at the fusion boundary due to the relatively high amount of alloying element in the hot-stamped boron steel, which could provide the reason for route of PF I extending along this zone. Fluctuation in the hardness in the transition zone led to the existence of both PF I and PF II at the same welding current.

scholarly journals Microstructure and Properties of Spot Welded Joints of Hot-Stamped Ultra-High Strength Steel Used for Automotive Body Structures

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 285 ◽  
Author(s):  
Zhixia Qiao ◽  
Huijun Li ◽  
Lianjin Li ◽  
Xiaoyu Ran ◽  
Liwen Feng
Keyword(s):  
Spot Welding ◽  
Mechanical Performance ◽  
High Strength Steels ◽  
High Hardness ◽  
High Strength ◽  
Resistance Spot ◽  
Automotive Body ◽  
Ultra High Strength Steels ◽  
Structural Parts ◽  
Spot Welded

Hot-stamped ultra-high strength steels have been widely used in automobile structural parts. Considering the high splash tendency in resistance spot welding due to their extremely high hardness, in this work, microstructural characteristics and mechanical performance of the resistance spot welded ultra-high strength steels are investigated. The results indicate that the interface between the nugget and heat-affected zone (HAZ) is the weakest zone where fractures initiate. In tensile shearing tests, a qualified spot welding joint failed with a button-shaped fracture. Welding defects would significantly decrease the load-carrying capacity and lead to interfacial fracture, except for a button-shaped fracture. In spot welding, it was found that a specific mid-frequency alternating current (AC) input mode, in which a 6 ms cooling cycle was inserted between every two neighboring current pulses, can avoid the splash in the spot welding of hot-stamped hardened steels.

scholarly journals Microstructure and Local Mechanical Properties of the Heat-Affected Zone of a Resistance Spot Welded Medium-Mn Steel

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3362
Author(s):  
Manfred Stadler ◽  
Ronald Schnitzer ◽  
Martin Gruber ◽  
Katharina Steineder ◽  
Christina Hofer
Keyword(s):  
Mechanical Properties ◽  
Heat Affected Zone ◽  
Great Influence ◽  
High Strength ◽  
Total Elongation ◽  
Resistance Spot ◽  
Heat Treated ◽  
Medium Mn Steel ◽  
Mn Steel ◽  
Spot Welded

The properties of the heat-affected zone (HAZ) are reported to have a great influence on the mechanical performance of resistance spot welded advanced high strength steels. Therefore, in the present work, the HAZ of a medium-Mn steel is characterized regarding its microstructure and its mechanical properties depending on the distance to the fusion zone (FZ). In order to obtain the local mechanical properties of the HAZ, samples were heat-treated in a joule-heating thermal simulator using different peak temperatures to physically simulate the microstructure of the HAZ. By comparing the microstructure and the hardness of these heat-treated samples and the HAZ, the local peak temperatures within the HAZ could be determined. Subsequently, tensile tests were conducted, and the austenite phase fraction was measured magnetically on the physically simulated HAZ samples in order to determine the local mechanical properties of the HAZ. As verified by energy-dispersive X-ray spectroscopy, peak temperatures above 1200 °C led to a uniform distribution of manganese, resulting in a predominantly martensitic microstructure with high strength and low total elongation after quenching. Below 1100 °C, the diffusion of manganese is restricted, and considerable fractions of austenite remain stable. The austenite fraction increases almost linearly with decreasing peak temperature, which leads to an increase of the total elongation and to a slight decrease in the strength, depending on the distance to the FZ. Temperatures below 700 °C exhibit hardly any effect on the initial microstructure and mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document