scholarly journals Fabrication of Adhesive Resistance Surface with Low Wettability on Ti6Al4V Alloys by Electro-Brush Plating

Micromachines ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 64 ◽  
Author(s):  
Xiaojuan Dong ◽  
Jianbing Meng ◽  
Haian Zhou ◽  
Rufeng Xu ◽  
Xue Bai ◽  
...  
Keyword(s):  
Contact Angle ◽  
Chemical Compositions ◽  
Sliding Angle ◽  
Water Contact ◽  
Resistance Surface ◽  
Adhesive Surface ◽  
Plating Method ◽  
Brush Plating ◽  
Solid Liquid Interface ◽  
Solid Liquid

Anti-adhesive Ni coatings with low wettability were successfully fabricated on Ti6Al4V substrates via an electro-brush plating method, and subsequently modified with a fluoroalkylsilane (FAS) film. The surface morphology, chemical compositions, and wettability of the as-prepared coatings were measured using scanning electron microscopy (SEM), X-ray diffractometer (XRD), Fourier transform infrared spectrophotometry (FTIR), and contact angle measurements. The results showed that the surface of Ti6Al4V substrate was endowed with flower-like structures. Each flower-like cluster was constituted by a large number of Ni ions. After surface modification of FAS, the as-prepared Ti6Al4V surface had a water contact angle as high as 151.5°, a sliding angle close to 2.1°, and a solid surface energy as low as 0.97 mJ/m2. Potentiodynamic polarization tests showed that the Ni coating could provide a stable corrosion protection. In addition, the effects of processing conditions, such as working voltage, relative velocity, electrolyte concentration, and processing time, were investigated. The mechanism of the adhesive resistance was proposed, and the low wettability of Ti6Al4V surfaces was explained by Cassie–Baxter model. As a result, it was necessary to reduce the fraction of the solid–liquid interface in order to achieve anti-adhesive surface.

Hydrophobicity of Teflon Coated Well-Ordered Silver Nanorod Arrays

2012 ◽  
Vol 1389 ◽  
Author(s):  
Arif S. Alagoz ◽  
Wisam J. Khudhayer ◽  
Tansel Karabacak
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Hierarchical Structures ◽  
Silicon Substrates ◽  
Nanorod Arrays ◽  
Water Contact ◽  
Glad Technique ◽  
Solid Liquid Interface ◽  
Solid Liquid ◽  
Angle Deposition

ABSTRACTFrom wings of flies to plant leafs, hydrophobic surfaces are well-common in nature. Many of these surfaces have micro and nano hierarchical structures coated with low surface energy layer. In this work, we mimicked similar structure by fabricating Teflon coated periodic and well-ordered silver nanorod arrays and investigated the effect of nanorod separation on water contact angle (WCA). The silver nanorod arrays were deposited on patterned and flat silicon substrates using glancing angle deposition (GLAD) technique. Then a thin layer of Teflon was deposited on the silver nanorods by small angle deposition (SAD) technique. A systematic increase in water contact angle was observed with increasing nanorod separation which is attributed to the decreased area fraction of solid-liquid interface.

scholarly journals Fabrication of a Low Adhesive Superhydrophobic Surface on Ti6Al4V Alloys Using TiO2/Ni Composite Electrodeposition

Micromachines ◽  
2019 ◽  
Vol 10 (2) ◽  
pp. 121 ◽  
Author(s):  
Jianbing Meng ◽  
Xiaojuan Dong ◽  
Yugang Zhao ◽  
Rufeng Xu ◽  
Xue Bai ◽  
...  
Keyword(s):  
Contact Angle ◽  
Wear Resistance ◽  
Superhydrophobic Surface ◽  
Ph Value ◽  
Chemical Compositions ◽  
Sliding Angle ◽  
Water Contact ◽  
Angle Measurements ◽  
Surface Morphologies ◽  
Composite Electrodeposition

A superhydrophobic surface with low adhesion and good wear resistance was fabricated on Ti6Al4V substrates via TiO2/Ni composite electrodeposition, and subsequently modified with a fluoroalkylsilane (FAS) film. Scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and optical contact angle measurements were used to characterize the surface morphologies, chemical compositions, and surface wettability. The superhydrophobicity of the as-prepared surface results from the fabrication of a hierarchical structure and the assembly of low-surface energy fluorinated components. The as-prepared surface had a water contact angle as high as 162.6° and a sliding angle close to 1.8°. Scratch and abrasion tests showed that the superhydrophobic coating provided a superior wear resistance and stable mechanical abrasion protection. In addition, the influence of processing conditions, such as working voltage, deposited time, pH value, and TiO2 concentration, was also investigated.

Dependence of the Contact Angle on Adsorption at the Solid-Liquid Interface

2010 ◽  
Author(s):  
C. A. Ward
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Pressure Range ◽  
Line Tension ◽  
Liquid Interface ◽  
Fluid Interfaces ◽  
Phase Line ◽  
Three Phase ◽  
Solid Liquid Interface ◽  
Solid Liquid

A method for determining the surface tension of solid-fluid interfaces has been proposed. For a given temperature and fluid-solid combination, these surface tensions are expressed in terms of material properties that can be determined by measuring the amount of vapor adsorbed on the solid surface as a function of xV, the ratio of the vapor-phase pressure to the saturation-vapor pressure. The thermodynamic concept of pressure is shown to be in conflict with that of continuum mechanics, but is supported experimentally. This approach leads to the prediction that the contact angle, θ, can only exist in a narrow pressure range and that in this pressure range, the solid-vapor surface tension is constant and equal to the surface tension of the liquid-vapor interface, γLV. The surface tension of the solid-liquid interface, γSL, may be expressed in terms of measurable properties, γLV and θ: γSL = γLV(1 − cosθ). The value of θ is predicted to depend on both the pressure in the liquid at the three-phase, line x3L, and the three-phase line curvature, Ccl. We examine these predictions using sessile water droplets on a polished Cu surface, maintained in a closed, constant volume, isothermal container. The value of θ is found to depend on the adsorption at the solid-liquid interface, nSL = nSL(x3L,Ccl). The predicted value of θ is compared with that measured, and found to be in close agreement, but no effect of line tension is found.

scholarly journals Transparent superhydrophobic PTFE films via one-step aerosol assisted chemical vapor deposition

RSC Advances ◽  
2017 ◽  
Vol 7 (47) ◽  
pp. 29275-29283 ◽  
Author(s):  
Aoyun Zhuang ◽  
Ruijin Liao ◽  
Sebastian C. Dixon ◽  
Yao Lu ◽  
Sanjayan Sathasivam ◽  
...  
Keyword(s):  
Contact Angle ◽  
Chemical Vapor Deposition ◽  
Water Contact Angle ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Sliding Angle ◽  
Water Contact ◽  
Visible Transmittance ◽  
One Step

Hierarchical micro/nano-structured transparent superhydrophobic polytetrafluoroethylene films with water contact angle 168°, water sliding angle <1° and visible transmittance >90% were prepared on glass via aerosol-assisted chemical vapor deposition.

Adsorption of azacrown ethers at solid–liquid interface. Contact angle and neutron reflectivity study

2009 ◽  
Vol 256 (1) ◽  
pp. 274-279 ◽  
Author(s):  
Kamil Wojciechowski ◽  
Anna Brzozowska ◽  
Sebastien Cap ◽  
Witold Rzodkiewicz ◽  
Thomas Gutberlet
Keyword(s):  
Contact Angle ◽  
Liquid Interface ◽  
Neutron Reflectivity ◽  
Azacrown Ethers ◽  
Interface Contact ◽  
Solid Liquid Interface ◽  
Solid Liquid

scholarly journals A Durable PVDF/PFOTES-SiO2 Superhydrophobic Coating on AZ31B Mg Alloy with Enhanced Abrasion Resistance Performance and Anti-Corrosion Properties

2021 ◽  
Vol 11 (23) ◽  
pp. 11172
Author(s):  
Zhiqiang Qian ◽  
Zhong Liu ◽  
Shidong Wang ◽  
XiuShen Ye ◽  
Zhijian Wu
Keyword(s):  
Contact Angle ◽  
Wear Resistance ◽  
Salt Spray ◽  
Mg Alloy ◽  
Superhydrophobic Coating ◽  
Friction Test ◽  
Sliding Angle ◽  
Sio2 Coating ◽  
Corrosion Properties ◽  
Water Contact

A simple and practical spray method is employed to prepare a PVDF/PFOTES-SiO2 superhydrophobic composite coating on the AZ31B Mg alloy substrate. The morphology, composition, and water contact angle (CA) were measured by Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscope (FESEM) and contact angle measuring instrument. Hydrophilic nano-SiO2 is modified by PFOTES to obtain hydrophobicity. The influence of the mass of PFOTES-SiO2 to PVDF on the hydrophobic properties was studied. The wear resistance and stability of the composite coating have been investigated by immersion test, cross-cut adhesion test and friction test. Additionally, the corrosion resistance was measured by electrochemical workstation and salt spray corrosion test. The CA of PVDF/PFOTES-SiO2 coating is 161.3° and the sliding angle (SAs) is less than 2°. After 10× the sandpaper friction test, the superhydrophobic contact angle of the coating remained above 155°, and the sliding angle was less than 5°, which indicated that the prepared coating is a strong superhydrophobic coating with good wear resistance. The results of the electrochemical tests show that the superhydrophobic coating improved the anti-corrosion performance of Mg alloy, and the water contact angle is greater than 150° after 168 h salt spray corrosion test. Due to its excellent superhydrophobicity, wear resistance and anti-corrosion properties, the robust PVDF/PFOTES-SiO2 coating is considered to have great potential for future applications in the automotive and marine industries.

Fabrication of Super-Hydrophobic Film on Tinplate’s Surface by a Simple Casting Method in Material Engineering and its Application

2012 ◽  
Vol 583 ◽  
pp. 374-378
Author(s):  
Qi Long Liu ◽  
Hong Chen ◽  
Hai Yun Jiang ◽  
Ruo Mei Wu ◽  
Zhi Qing Yuan ◽  
...  
Keyword(s):  
Contact Angle ◽  
Composite Film ◽  
Hydrophobic Effect ◽  
Contact Angles ◽  
Casting Method ◽  
Sliding Angle ◽  
Water Contact ◽  
Drying Time ◽  
Practical Applications ◽  
Material Engineering

A simple, cheap and environmental double thin super-hydrophobic composite film was prepared on the surface of tinplate by a simple casting method. The contact angle and sliding angle were measured by an optical contact angle meter. And the major factors that influenced the super-hydrophobic effect of the composite film were studied in our work. The results showed that when the melting temperature was 120°C, the weight radio of PP and PP-g-MAH was 1:4, the drying time was 24h, the dosage of ethanol was 0.4ml, the composite film showed a satisfactory super-hydrophobicity and its water contact angles reached a maximum value of 156.6° while the sliding angle reached a minimum value of 2°. Because of anti-oxidation, moisture-proof and anticorrosion performance of super-hydrophobic tinplate, it has potential practical applications in packaging material engineering.

Micro-Nanostructured Silicone Rubber Surfaces Using Compression Molding

2018 ◽  
Vol 941 ◽  
pp. 1802-1807 ◽  
Author(s):  
Khosrow Maghsoudi ◽  
Gelareh Momen ◽  
Reza Jafari ◽  
Masoud Farzaneh ◽  
Tony Carreira
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Silicone Rubber ◽  
Surface Characterization ◽  
Contact Angle Hysteresis ◽  
Compression Molding ◽  
Sliding Angle ◽  
Water Contact ◽  
Superhydrophobic Property ◽  
Aluminum Surfaces

A facile method is introduced for production of micro-nanostructured silicone rubber surfaces by means of direct replication using a compression molding system. The fabricated samples possessing surface roughness display water contact angle of more than 160o and contact angle hysteresis (CAH) and sliding angle of less than 5o. Such low surface wettability of silicone specimens verifies the induced superhydrophobic property. Chemically etched aluminum surfaces could work excellently as templates whose patterns were replicated on the rubber surfaces successfully. Various etching conditions were examined. Surface characterization techniques revealed the presence of micro-nanostructures on the produced silicone surfaces.

Sign in / Sign up

Export Citation Format

Share Document