scholarly journals Theoretical Study on Widening Bandwidth of Piezoelectric Vibration Energy Harvester with Nonlinear Characteristics

Micromachines ◽  
2021 ◽  
Vol 12 (11) ◽  
pp. 1301
Author(s):  
Zhang Qichang ◽  
Yang Yang ◽  
Wang Wei
Keyword(s):  
Frequency Band ◽  
Energy Harvester ◽  
Primary Resonance ◽  
Subharmonic Resonance ◽  
Vibration Energy ◽  
Frequency Range ◽  
Nonlinear Characteristics ◽  
Vibration Energy Harvester ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

In order to make a piezoelectric vibration energy harvester collect more energy on a broader frequency range, nonlinearity is introduced into the system, allowing the harvester to produce multiple steady states and deflecting the frequency response curve. However, the harvester can easily maintain intra-well motion rather than inter-well motion, which seriously affects its efficiency. The aim of this paper is to analyze how to take full advantage of the nonlinear characteristics to widen the bandwidth of the piezoelectric vibration energy harvester and obtain more energy. The influence of the inter-permanent magnet torque on the bending of the piezoelectric cantilever beam is considered in the theoretical modeling. The approximate analytical solutions of the primary and 1/3 subharmonic resonance of the harvester are obtained by using the complex dynamic frequency (CDF) method so as to compare the energy acquisition effect of the primary resonance and subharmonic resonance, determine the generation conditions of subharmonic resonance, and analyze the effect of primary resonance and subharmonic resonance on broadening the bandwidth of the harvester under different external excitations. The results show that the torque significantly affects the equilibrium point and piezoelectric output of the harvester. The effective frequency band of the bistable nonlinear energy harvester is 270% wider than that of the linear harvester, and the 1/3 subharmonic resonance broadens the band another 92% so that the energy harvester can obtain more than 0.1 mW in the frequency range of 18 Hz. Therefore, it is necessary to consider the influence of torque when modeling. The introduction of nonlinearity can broaden the frequency band of the harvester when it is in primary resonance, and the subharmonic resonance can make the harvester obtain more energy in the global frequency range.

A Broadband Frequency Piezoelectric Vibration Energy Harvester

2011 ◽  
Vol 483 ◽  
pp. 626-630 ◽  
Author(s):  
Hua An Ma ◽  
Jing Quan Liu ◽  
Gang Tang ◽  
Chun Sheng Yang ◽  
Yi Gui Li ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Frequency Band ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Piezoelectric Cantilever ◽  
Working Frequency ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

As the low-power wireless sensor components and the development of micro electromechanical systems, long-term supply of components is a major obstacle of their development. One of solutions to this problem is based on the environmental energy collection of piezoelectric vibration energy harvesting. Currently, frequency band of piezoelectric vibration energy harvester is narrow and the frequency is high, which is not fit for the vibration energy acquisition in the natural environment. A piezoelectric vibration energy harvester with lower working frequency and broader band is designed and a test system to analyze the harvester is presented in this paper. The traditional mass is replaced by a permanent magnet in this paper, While other two permanent magnets are also placed on the upper and above of the piezoelectric cantilever. Experiments showed, under the 0.5g acceleration, compared with the traditional non-magnetic piezoelectric vibration energy harvesting, a piezoelectric cantilever (length 40mm, width 8mm, thickness 0.8mm) has a peak-peak voltage of 32.4V, effectively enlarges working frequency band from 67HZ-105HZ to 63HZ-108HZ.

scholarly journals Segmented Cantilever and Array Configurations for Wider Frequency Band and Higher Power Generation in Piezoelectric Vibration Energy Harvester

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Aicheng Zou ◽  
Jiefeng Li ◽  
Xingguo Han ◽  
Qunying Wang
Keyword(s):  
Frequency Band ◽  
Energy Harvester ◽  
Load Resistance ◽  
Vibration Energy ◽  
Total Output ◽  
Cantilever Beams ◽  
Vibration Energy Harvester ◽  
Operation Frequency ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

This letter reports a piezoelectric vibration energy harvester which energy conversion efficiency is significantly improved by arraying piezoelectric sheets on cantilever beams, and the operation frequency band is widened by applying two-segment cantilever beams. A prototype is developed and tested. In this case, two group piezoelectric arrays are combined on the cantilever beams with the optimum load resistance. The total output power remains above 6.54 mW within the operation frequency band ranges from 27.5 Hz to 37.5 Hz when the generator is under an acceleration of 0.7 g and reaches two power peaks: 20.5 mW at 29.2 Hz and 12.95 mW at 35.4 Hz.

scholarly journals Theoretical and Experimental Studies on MEMS Variable Cross-Section Cantilever Beam Based Piezoelectric Vibration Energy Harvester

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 772
Author(s):  
Xianming He ◽  
Dongxiao Li ◽  
Hong Zhou ◽  
Xindan Hui ◽  
Xiaojing Mu
Keyword(s):  
Power Density ◽  
Cantilever Beam ◽  
Cross Section ◽  
Energy Harvester ◽  
Variable Cross Section ◽  
Vibration Energy ◽  
Variable Cross ◽  
Vibration Energy Harvester ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

The piezoelectric vibration energy harvester (PVEH) based on the variable cross-section cantilever beam (VCSCB) structure has the advantages of uniform axial strain distribution and high output power density, so it has become a research hotspot of the PVEH. However, its electromechanical model needs to be further studied. In this paper, the bidirectional coupled distributed parameter electromechanical model of the MEMS VCSCB based PVEH is constructed, analytically solved, and verified, which laid an important theoretical foundation for structural design and optimization, performance improvement, and output prediction of the PVEH. Based on the constructed model, the output performances of five kinds of VCSCB based PVEHs with different cross-sectional shapes were compared and analyzed. The results show that the PVEH with the concave quadratic beam shape has the best output due to the uniform surface stress distribution. Additionally, the influence of the main structural parameters of the MEMS trapezoidal cantilever beam (TCB) based PVEH on the output performance of the device is theoretically analyzed. Finally, a prototype of the Aluminum Nitride (AlN) TCB based PVEH is designed and developed. The peak open-circuit voltage and normalized power density of the device can reach 5.64 V and 742 μW/cm3/g2, which is in good agreement with the theoretical model value. The prototype has wide application prospects in the power supply of the wireless sensor network node such as the structural health monitoring system and the Internet of Things.

Analysis of a Curved Beam MEMS Piezoelectric Vibration Energy Harvester

2010 ◽  
Vol 139-141 ◽  
pp. 1578-1581 ◽  
Author(s):  
Yong Zhou ◽  
Yong Dong ◽  
Shi Li
Keyword(s):  
Energy Harvester ◽  
Dynamic Performance ◽  
Beam Theory ◽  
Vibration Energy ◽  
Curved Beam ◽  
Vibration Energy Harvester ◽  
Coupling Vibration ◽  
Structural Assembly ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

An analytical model is derived for obtaining the dynamic performance of a thin curved composite piezoelectric beam with variable curvatures for the MEMS piezoelectric vibration energy harvester. The plane curved beam theory with rectangular section is employed to explore the bending and twisting coupling vibration characteristics. In order to satisfy the most available environmental frequencies, which are on the order of 1000Hz, the parameters of the spiraled composite beam bonded with piezoelectric on the surfaces are investigated to provide a method of how to design low resonance beams while keeping the compacting structural assembly. The results indicate the adoption of ANSYS® software to carry out the MEMS piezoelectric vibration energy harvester’s numerical simulation can improve the accuracy of the harvester designing and manufacturing consumedly. And the simulation data also provide a theory analysis foundation for the engineering, design and application of harvester.

Sign in / Sign up

Export Citation Format

Share Document