scholarly journals Characterization of the Physical, Chemical, and Adsorption Properties of Coal-Fly-Ash–Hydroxyapatite Composites

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 774
Author(s):  
Eleonora Sočo ◽  
Dorota Papciak ◽  
Magdalena M. Michel ◽  
Dariusz Pająk ◽  
Andżelika Domoń ◽  
...  
Keyword(s):  
Fly Ash ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Synthesis Conditions ◽  
High Calcium ◽  
Ft Ir ◽  
Ir Analysis ◽  
Wet Synthesis

(1) Hydroxyapatite (Hap), which can be obtained by several methods, is known to be a good adsorbent. Coal fly ash (CFA) is a commonly reused byproduct also used in environmental applications as an adsorbent. We sought to answer the following question: Can CFA be included in the method of Hap wet synthesis to produce a composite capable of adsorbing both heavy metals and dyes? (2) High calcium lignite CFA from the thermal power plant in Bełchatów (Poland) was used as the base to prepare CFA–Hap composites. Four types designated CFA–Hap1–4 were synthesized via the wet method of in situ precipitation. The synthesis conditions differed in terms of the calcium reactants used, pH, and temperature. We also investigated the equilibrium adsorption of Cu(II) and rhodamine B (RB) on CFA–Hap1–4. The data were fitted using the Langmuir, Freundlich, and Redlich–Peterson models and validated using R2 and χ2/DoF. Surface changes in CFA–Hap2 following Cu(II) and RB adsorption were assessed using SEM, SE, and FT-IR analysis. (3) The obtained composites contained hydroxyapatite (Ca/P 1.67) and aluminosilicates. The mode of Cu(II) and RB adsorption could be explained by the Redlich–Peterson model. The CFA–Hap2 obtained using CFA, Ca(NO3)2, and (NH4)2HPO4 at RT and pH 11 exhibited the highest maximal adsorption capacity: 73.6 mg Cu/g and 87.0 mg RB/g. (4) The clear advantage of chemisorption over physisorption was indicated by the Cu(II)–CFA–Hap system. The RB molecules present in the form of uncharged lactone were favorably adsorbed even on strongly deprotonated CFA–Hap surfaces.

Characterization of Geopolymer Materials Containing MSWI Fly Ash and Coal Fly Ash

2010 ◽  
Vol 69 ◽  
pp. 123-128 ◽  
Author(s):  
Salvatore Andini ◽  
Raffaele Cioffi ◽  
Francesco Colangelo ◽  
Claudio Ferone ◽  
Fabio Montagnaro ◽  
...  
Keyword(s):  
Fly Ash ◽  
Coal Fly Ash ◽  
Mswi Fly Ash ◽  
Three Samples ◽  
Chemical Behaviour ◽  
Ft Ir ◽  
Ft Ir Spectroscopy ◽  
Polycondensation Products

In this work three samples of MSWI ash have been stabilized in systems containing coal fly ash and able to give geopolymers through a polycondensation reaction. Monolithic products were obtained with both MSWI ashes as received and after chloride partial removal by water washing. The polycondensation products have been characterized qualitatively by means of FT-IR spectroscopy and scanning electron microscopy (SEM) and quantitatively through the determination of the amount of reacted water and silicate. Differently from traditional cement based stabilization systems, those based on geopolymerization show a chemical behaviour almost insensitive to the presence of chlorides and sulphates in the MSWI ash. On the other hand, the microstructure is strongly affected by the content of soluble salts.

scholarly journals Hybrid Fly Ash-Based Geopolymeric Foams: Microstructural, Thermal and Mechanical Properties

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2919 ◽  
Author(s):  
Giuseppina Roviello ◽  
Laura Ricciotti ◽  
Antonio Jacopo Molino ◽  
Costantino Menna ◽  
Claudio Ferone ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Circular Economy ◽  
Coal Fly Ash ◽  
Silicate Solution ◽  
Thermal And Mechanical Properties ◽  
Blowing Agent ◽  
Materials Used

This research investigates the preparation and characterization of new organic–inorganic geopolymeric foams obtained by simultaneously reacting coal fly ash and an alkali silicate solution with polysiloxane oligomers. Foaming was realized in situ using Si0 as a blowing agent. Samples with density ranging from 0.3 to 0.7 g/cm3 that show good mechanical properties (with compressive strength up to ≈5 MPa for a density of 0.7 g/cm3) along with thermal performances (λ = 0.145 ± 0.001 W/m·K for the foamed sample with density 0.330 g/cm3) comparable to commercial lightweight materials used in the field of thermal insulation were prepared. Since these foams were obtained by valorizing waste byproducts, they could be considered as low environmental impact materials and, hence, with promising perspectives towards the circular economy.

scholarly journals Romanian bentonite and fly ash characterization and their use in heavy metal “in-situ” immobilization in polluted soils

2017 ◽  
Vol 18 ◽  
pp. 01022
Author(s):  
Săndica Liliana Gherghe ◽  
Ildiko Anger ◽  
Georgiana Moise ◽  
Roxana Trusca
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Fly Ash ◽  
Contact Time ◽  
In Situ Immobilization ◽  
Polluted Soils ◽  
Ft Ir ◽  
Metallurgical Activities

This article presents the characterization of the Romanian bentonite and fly ash, using different techniques: FAAS, XRD, FT-IR, SEM and EDAX and their evaluation as sorbents for heavy metals immobilization in polluted soils coming from mining and metallurgical activities. The applicability of bentonite and fly ash for Pb (II) and Zn (II) immobilization was studied using aqueous solutions of these metals. The influence of the pH and contact time were studied. The results shown that the Romanian bentonite and fly ash could be used for Pb (II) and Zn (II) immobilization in polluted soils from brownfields.

scholarly journals Effect of Additive Material on Controlling Chromium (Cr) Leaching from Coal Fly Ash

Minerals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 563
Author(s):  
Erda Rahmilaila Desfitri ◽  
Ulung Muhammad Sutopo ◽  
Yukio Hayakawa ◽  
Shinji Kambara
Keyword(s):  
Fly Ash ◽  
Inductively Coupled Plasma ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Calcium Content ◽  
High Calcium ◽  
Cr Concentration ◽  
Additive Materials ◽  
Sludge Ash

Coal fly ash contains a considerable number of toxic elements that can be leached into the environment, such as chromium (Cr), thereby quickly leading to severe contaminations. In this research, the leaching behaviors of Cr were analyzed from 14 kinds of coal fly ash samples collected from the electrostatic precipitators of coal-fired thermal power plants in Japan. The level of Cr concentration found in the samples varied from 0.00 to 82.93 μg/L. However, Cr toxicity depends on its valence state; Cr6+ is more toxic than Cr3+. Additive materials containing high calcium content were used to control the leaching concentration of Cr, such as Ca(OH)2, paper sludge ash, and blast furnace cement. This research used several instruments. An X-ray fluorescence was adopted to measure the major chemical composition of the fly ash samples and the additive materials. A thermogravimetric analyzer was used to examine the calcium compounds in the additive materials. Inductively coupled plasma was used to determine the Cr leaching concentrations from the fly ash samples. Findings showed that the three-additive mixture had a promising effect on controlling the Cr leaching concentrations. These results were also supported by FactSage 7.2 simulation.

Synthesis and characterization of coal fly ash supported zinc oxide catalyst for biodiesel production using used cooking oil as feed

2021 ◽  
Vol 170 ◽  
pp. 302-314
Author(s):  
Adeyinka S. Yusuff ◽  
Aman K. Bhonsle ◽  
Jayati Trivedi ◽  
Dinesh P. Bangwal ◽  
Lok P. Singh ◽  
...  
Keyword(s):  
Zinc Oxide ◽  
Fly Ash ◽  
Oxide Catalyst ◽  
Coal Fly Ash ◽  
Biodiesel Production ◽  
Synthesis And Characterization ◽  
Cooking Oil ◽  
Used Cooking Oil

scholarly journals Preparation of Synthetic Zeolites from Coal Fly Ash by Hydrothermal Synthesis

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1267
Author(s):  
David Längauer ◽  
Vladimír Čablík ◽  
Slavomír Hredzák ◽  
Anton Zubrik ◽  
Marek Matik ◽  
...  
Keyword(s):  
Fly Ash ◽  
Coal Combustion ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Product Analysis ◽  
Coal Combustion Products ◽  
X Ray ◽  
Wide Range ◽  
Silica Alumina

Large amounts of coal combustion products (as solid products of thermal power plants) with different chemical and physical properties cause serious environmental problems. Even though coal fly ash is a coal combustion product, it has a wide range of applications (e.g., in construction, metallurgy, chemical production, reclamation etc.). One of its potential uses is in zeolitization to obtain a higher added value of the product. The aim of this paper is to produce a material with sufficient textural properties used, for example, for environmental purposes (an adsorbent) and/or storage material. In practice, the coal fly ash (No. 1 and No. 2) from Czech power plants was firstly characterized in detail (X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), particle size measurement, and textural analysis), and then it was hydrothermally treated to synthetize zeolites. Different concentrations of NaOH, LiCl, Al2O3, and aqueous glass; different temperature effects (90–120 °C); and different process lengths (6–48 h) were studied. Furthermore, most of the experiments were supplemented with a crystallization phase that was run for 16 h at 50 °C. After qualitative product analysis (SEM-EDX, XRD, and textural analytics), quantitative XRD evaluation with an internal standard was used for zeolitization process evaluation. Sodalite (SOD), phillipsite (PHI), chabazite (CHA), faujasite-Na (FAU-Na), and faujasite-Ca (FAU-Ca) were obtained as the zeolite phases. The content of these zeolite phases ranged from 2.09 to 43.79%. The best conditions for the zeolite phase formation were as follows: 4 M NaOH, 4 mL 10% LiCl, liquid/solid ratio of 30:1, silica/alumina ratio change from 2:1 to 1:1, temperature of 120 °C, process time of 24 h, and a crystallization phase for 16 h at 50 °C.

scholarly journals Assessment of Characteristics of Acid Mine Drainage Treated with Fly Ash

2021 ◽  
Vol 11 (9) ◽  
pp. 3910
Author(s):  
Saba Shirin ◽  
Aarif Jamal ◽  
Christina Emmanouil ◽  
Akhilesh Kumar Yadav
Keyword(s):  
Fly Ash ◽  
Acid Mine Drainage ◽  
Power Plants ◽  
Mine Drainage ◽  
Thermal Power ◽  
Mineralogical Characterization ◽  
Acid Mine ◽  
Before And After ◽  
Abandoned Coal Mines

Acid mine drainage (AMD) occurs naturally in abandoned coal mines, and it contains hazardous toxic elements in varying concentrations. In the present research, AMD samples collected from an abandoned mine were treated with fly ash samples from four thermal power plants in Singrauli Coalfield in the proximate area, at optimized concentrations. The AMD samples were analyzed for physicochemical parameters and metal content before and after fly ash treatment. Morphological, geochemical and mineralogical characterization of the fly ash was performed using SEM, XRF and XRD. This laboratory-scale investigation indicated that fly ash had appreciable neutralization potential, increasing AMD pH and decreasing elemental and sulfate concentrations. Therefore, fly ash may be effectively used for AMD neutralization, and its suitability for the management of coalfield AMD pits should be assessed further.

FT-IR and micro-Raman spectroscopic characterization of minerals in high-calcium coal ashes

2018 ◽  
Vol 91 (3) ◽  
pp. 389-396 ◽  
Author(s):  
Yanshan Yin ◽  
Jie Yin ◽  
Wei Zhang ◽  
Hong Tian ◽  
Zhangmao Hu ◽  
...  
Keyword(s):  
Spectroscopic Characterization ◽  
Raman Spectroscopic ◽  
High Calcium ◽  
Ft Ir ◽  
Coal Ashes

Diffuse Reflectance FT-IR Characterization of Active Sites under Reaction Conditions: The Production of Oxygenates in the CO/H2 Reaction

1994 ◽  
Vol 48 (10) ◽  
pp. 1208-1212 ◽  
Author(s):  
J. J. Benítez ◽  
I. Carrizosa ◽  
J. A. Odriozola
Keyword(s):  
Infrared Spectra ◽  
Active Sites ◽  
Diffuse Reflectance ◽  
Reaction Conditions ◽  
In Situ Drifts ◽  
Ft Ir

The reactivity of a Lu2O3-promoted Rh/Al2O3 catalyst in the CO/H2 reaction is reported. Methane, heavier hydrocarbons, methanol, and ethanol are obtained. In situ DRIFTS has been employed to record the infrared spectra under the actual reaction conditions. The structure of the observed COads DRIFTS bands has been resolved into its components. The production of oxygenates (methanol and ethanol) has been correlated with the results of the deconvolution calculation. Specific sites for the production of methanol and ethanol in the CO/H2 reaction over a Rh,Lu2O3/Al2O3 catalyst are proposed.

Sign in / Sign up

Export Citation Format

Share Document