scholarly journals Investigation of Position Sensing and Energy Harvesting of a Flexible Triboelectric Touch Pad

Nanomaterials ◽  
2018 ◽  
Vol 8 (8) ◽  
pp. 613 ◽  
Author(s):  
Tao Chen ◽  
Qiongfeng Shi ◽  
Kunpu Li ◽  
Zhan Yang ◽  
Huicong Liu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Short Circuit ◽  
Electronic Devices ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Triboelectric Nanogenerator ◽  
Maximum Output ◽  
Current Output ◽  
Position Sensing

Triboelectric nanogenerator (TENG) is a promising technology because it can harvest energy from the environment to enable self-sustainable mobile and wearable electronic devices. In this work, we present a flexible touch pad capable of detecting the contact location of an object and generating substantial energy simultaneously based on the coupling of triboelectric effects and electrostatic induction. The touch pad consists of Polytetrafluoroethylene (PTFE) thin film, multiple Aluminum (Al) electrodes and Polyethylene terephthalate (PET) layers, which can be achieved through low cost, simplified and scalable fabrication process. Different from the conventional multi-pixel-based positioning sensor (i.e., large array of sensing elements and electrodes), the analogue method proposed here is used to implement the positioning function with only four electrodes. Position location can achieve a detecting resolution of as small as 1.3 mm (the size of locating layer is 7.5 cm × 7.5 cm). For the energy harvesting part, a multilayer structure is designed to provide higher current output. The open circuit voltage of the device is around 420 V and the short circuit current can reach up to 6.26 µA with current density of 0.25 µA/cm2. The maximum output power obtained is approximately 10 mW, which is 0.4 mW/cm2. The flexibility and significantly reduced number of electrodes enable the proposed touch pad to be readily integrated into portable electronic devices, such as intelligent robots, laptops, healthcare devices, and environmental surveys, etc.

Maximum Output Power Control Using Short-Circuit Current and Open-Circuit Voltage of a Solar Panel

2012 ◽  
Vol 51 (10S) ◽  
pp. 10NF08 ◽  
Author(s):  
Takahiro Kato ◽  
Takuma Miyake ◽  
Daisuke Tashima ◽  
Tatsuya Sakoda ◽  
Masahisa Otsubo ◽  
...  
Keyword(s):  
Power Control ◽  
Output Power ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Solar Panel ◽  
Maximum Output

Output Characteristics Study of V-trough PV Concentration System

2011 ◽  
Vol 71-78 ◽  
pp. 2077-2080 ◽  
Author(s):  
Cui Qiong Yan
Keyword(s):  
Output Power ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Open Circuit ◽  
Maximum Output ◽  
Water Cooling ◽  
Cell Array ◽  
Pv System ◽  
Current Output ◽  
Super Cell

A V-trough PV system with polysilicon cell array and super cell array has been constructed and tested. Open-circuit voltage, short-circuit current, output power, fill factor and influence of temperature on V-trough PV concentration system have been analyzed. The results indicate that the output power of 10 pieces of polysilicon cell array is 6.198W and it is 1.21 times as that of non-concentration condition. Maximum output power of V-trough PV system with water cooling increase to 8.28W and power increment rate reach 62.67% compared with the non-concentration PV system. For the super cell array with no water cooling, the maximum output power of V-trough PV system varies from 7.834W to 14.223W. The results of this work provide some experimental support to the applications of the V-trough PV system.

Performance Study of GaAs Photovoltaic Power Converter in Optically Powered Systems

2014 ◽  
Vol 556-562 ◽  
pp. 1894-1897
Author(s):  
Xin Wei Yuan ◽  
Jie Qin Shi
Keyword(s):  
Short Circuit ◽  
Electrical Power ◽  
Maximum Output Power ◽  
Optical Power ◽  
Short Circuit Current ◽  
Power Converter ◽  
Open Circuit ◽  
Maximum Output ◽  
Performance Study ◽  
Photovoltaic Power

Optically powered system is a revolutionary new power delivery system, in which optical power is delivered over fiber to photovoltaic power converter, where optical power is transformed into electrical power. Therefore the system is inherently immune to RF, EMI, high voltage and lighting effects. Capable of powering electronic circuitry by optical fiber, this technology has been validated in industries such as electric power, communications, remote sensing and aerospace. To a large extent, photovoltaic power converter is a key component that decides the performance of optically powered system. In this paper, the commonly used GaAs photovoltaic power converter is studied and tested. Parameter values like open circuit voltage, short circuit current, maximum output power, conversion efficiency and the optimum load resistance are obtained through experiment, which can be severed as important reference while choosing or designing DC-DC converter.

Study on the Illumination Characteristics of Solar Photovoltaic Battery

2015 ◽  
Vol 1092-1093 ◽  
pp. 91-95
Author(s):  
Zhen Yong Liu ◽  
Jian Qi Sun ◽  
Zhi Chun Ma
Keyword(s):  
Light Intensity ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Cell Sheet ◽  
Single Crystal Silicon ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Maximum Output ◽  
Solar Panels ◽  
Crystal Silicon

Effects of solar panels must be taken into account by the light intensity of its output characteristics in practical application, especially solar panels placed outdoor. So the light intensity coefficient is an important parameter to be considered. In this paper,we took the light intensity characteristics of single crystal silicon solar cell as the research object. Also,through transforming the illumination intensity which are 777.60W/m2,996.97 W/m2 and 1224.88 W/m2, we would finish researching the characteristics of the cell sheet, which included battery plate volt ampere characteristic, open circuit voltage, short circuit current and maximum output power. Also, we’ve got the relationship of Uoc-T, Isc-T and Pm-T, respectively and Put forward the better intensity theory. It would lay a solid foundation of practice for the further study on how to improve the rate of light conversion.

Maximum Output Power Control Using Short-Circuit Current and Open-Circuit Voltage of a Solar Panel

2012 ◽  
Vol 51 ◽  
pp. 10NF08
Author(s):  
Takahiro Kato ◽  
Takuma Miyake ◽  
Daisuke Tashima ◽  
Tatsuya Sakoda ◽  
Masahisa Otsubo ◽  
...  
Keyword(s):  
Power Control ◽  
Output Power ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Solar Panel ◽  
Maximum Output

scholarly journals A Stretchable, Self-Healable Triboelectric Nanogenerator as Electronic Skin for Energy Harvesting and Tactile Sensing

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1689
Author(s):  
Xi Han ◽  
Dongjie Jiang ◽  
Xuecheng Qu ◽  
Yuan Bai ◽  
Yu Cao ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Material Selection ◽  
Short Circuit ◽  
Red Light ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Triboelectric Nanogenerator ◽  
Tactile Sensing ◽  
Electronic Skin ◽  
Self Powered

Electronic skin that is deformable, self-healable, and self-powered has high competitiveness for next-generation energy/sense/robotic applications. Herein, we fabricated a stretchable, self-healable triboelectric nanogenerator (SH-TENG) as electronic skin for energy harvesting and tactile sensing. The elongation of SH-TENG can achieve 800% (uniaxial strain) and the SH-TENG can self-heal within 2.5 min. The SH-TENG is based on the single-electrode mode, which is constructed from ion hydrogels with an area of 2 cm × 3 cm, the output of short-circuit transferred charge (Qsc), open-circuit voltage (Voc), and short-circuit current (Isc) reaches ~6 nC, ~22 V, and ~400 nA, and the corresponding output power density is ~2.9 μW × cm−2 when the matching resistance was ~140 MΩ. As a biomechanical energy harvesting device, the SH-TENG also can drive red light-emitting diodes (LEDs) bulbs. Meanwhile, SH-TENG has shown good sensitivity to low-frequency human touch and can be used as an artificial electronic skin for touch/pressure sensing. This work provides a suitable candidate for the material selection of the hydrogel-based self-powered electronic skin.

scholarly journals A Highly Efficient and Durable Kirigami Triboelectric Nanogenerator for Rotational Energy Harvesting

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1120
Author(s):  
Dae Sol Kong ◽  
Jae Yeon Han ◽  
Young Joon Ko ◽  
Sang Hyeok Park ◽  
Minbaek Lee ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Sliding Mode ◽  
Short Circuit ◽  
Three Dimensional ◽  
Short Circuit Current ◽  
Rotational Energy ◽  
Open Circuit ◽  
Triboelectric Nanogenerator ◽  
Highly Efficient ◽  
Triboelectric Nanogenerators

While sliding-mode triboelectric nanogenerators (S-TENGs) have been considered as one of the most promising devices for rotational energy harvesting, their inherently poor durability has been a serious bottleneck for applications. Herein, we report a three-dimensional kirigami TENG as a highly efficient and durable rotational energy harvesting device. The kirigami TENG consisted of cube-shaped paper, aluminum (Al) foil electrode and polytetrafluoroethylene (PTFE) polymer film, and converted rotational motion into multiple folding-unfolding vibrations. The rotation-folding (R-F) kirigami TENG generated an open-circuit voltage of 31 V, a short-circuit current of 0.67 μA and an instantaneous power (power density) of 1.2 μW (0.13 μW/cm2) at 200 rpm, which was sufficient to turn on 25 light-emitting diodes and a thermo-hygrometer. The triboelectric outputs of the R-F kirigami TENG were only slightly decreased even after 288,000 continuous rotations, i.e., the output remained at 86% of its initial value. This work demonstrates that an R-F kirigami TENG could be a plausible candidate to efficiently harvest various forms of rotational energy with a long-term durability.

scholarly journals Fabrication and Optoelectrical Properties of IZO/Cu2OHeterostructure Solar Cells by Thermal Oxidation

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Cheng-Chiang Chen ◽  
Lung-Chien Chen ◽  
Yi-Hsuan Lee
Keyword(s):  
Solar Cells ◽  
Fill Factor ◽  
Open Circuit Voltage ◽  
Low Cost ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Maximum Output ◽  
Indium Zinc Oxide

Indium zinc oxide (IZO)/cupper oxide (Cu2O) is a nontoxic nature and an attractive all-oxide candidate for low-cost photovoltaic (PV) applications. The present paper reports on the fabrication of IZO/Cu2O heterostructure solar cells which the Cu2O layers were prepared by oxidation of Cu thin films deposited on glass substrate. The measured parameters of cells were the short-circuit current (Isc), the open-circuit voltage (Voc), the maximum output power (Pm), the fill factor (FF), and the efficiency (η), which had values of 0.11 mA, 0.136 V, 5.05 μW, 0.338, and 0.56%, respectively, under AM 1.5 illumination.

scholarly journals The Effect of Temperature on the Solar Cell Efficiency, Output Currents and Voltages

2021 ◽  
Vol 13 (2) ◽  
pp. 55
Author(s):  
Asim Ahmed Mohamed Fadol ◽  
Mohammed M. Rashed ◽  
L. M. Abdalgadir ◽  
Essam E. Ali
Keyword(s):  
Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Effect Of Temperature ◽  
Maximum Output ◽  
Current Increase ◽  
Increasing Temperature

Experimental results shows that all electrical parameters of solar cell such as maximum output power, open circuit voltage, short circuit current, and fill factor beside efficiency have been changed with temperature. According to results, the most significant is the temperature dependence of the voltage which decreases with increasing temperature while the current of cells slightly increases by temperature. The fill factor and the efficiency decrease upon increasing temperature. This confirms the fact that the voltage decrease is more significant than the current increase.

scholarly journals Power Generation from a Hybrid Generator (TENG-EMG) Run by a Thermomagnetic Engine Harnessing Low Temperature Waste Heat

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1774 ◽  
Author(s):  
Zeeshan ◽  
Rahate Ahmed ◽  
Wongee Chun ◽  
Seung Jin Oh ◽  
Yeongmin Kim
Keyword(s):  
Low Temperature ◽  
Cold Water ◽  
Waste Heat ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Open Circuit ◽  
Triboelectric Nanogenerator ◽  
Maximum Output ◽  
Rotating Shaft ◽  
Hybrid Generator

This work explored the scavenging of low temperature waste heat and conversion of it into electrical energy through the operation of a gadolinium (Gd) based thermomagnetic engine. Gd is one of the unique materials whose magnetic property changes from ferromagnetic to paramagnetic depending on the temperature (“the Curie temperature”), which is around 20 °C. In the present work, two different types of generators were designed and applied to the rotating shaft of a Gd-based thermomagnetic engine developed for low temperature differential (LTD) applications. Of these, one is the so-called triboelectric nanogenerator (TENG), and the other is the electromagnetic generator (EMG). These have been designed to produce electricity from the rotating shaft of the thermomagnetic engine, exploiting both the electromagnetic and triboelectric effects. When operated at a rotational speed of 251 rpm with a temperature difference of 45 °C between the hot and cold water jets, the hybrid (TENG-EMG) generator produced a combined pulsating DC open circuit voltage of 5 V and a short circuit current of 0.7 mA. The hybrid generator effectively produced a maximum output power of 0.75 mW at a loading resistance of 10 kΩ.

Sign in / Sign up

Export Citation Format

Share Document