Study on the Illumination Characteristics of Solar Photovoltaic Battery

2015 ◽  
Vol 1092-1093 ◽  
pp. 91-95
Author(s):  
Zhen Yong Liu ◽  
Jian Qi Sun ◽  
Zhi Chun Ma
Keyword(s):  
Light Intensity ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Cell Sheet ◽  
Single Crystal Silicon ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Maximum Output ◽  
Solar Panels ◽  
Crystal Silicon

Effects of solar panels must be taken into account by the light intensity of its output characteristics in practical application, especially solar panels placed outdoor. So the light intensity coefficient is an important parameter to be considered. In this paper,we took the light intensity characteristics of single crystal silicon solar cell as the research object. Also,through transforming the illumination intensity which are 777.60W/m2,996.97 W/m2 and 1224.88 W/m2, we would finish researching the characteristics of the cell sheet, which included battery plate volt ampere characteristic, open circuit voltage, short circuit current and maximum output power. Also, we’ve got the relationship of Uoc-T, Isc-T and Pm-T, respectively and Put forward the better intensity theory. It would lay a solid foundation of practice for the further study on how to improve the rate of light conversion.

Maximum Output Power Control Using Short-Circuit Current and Open-Circuit Voltage of a Solar Panel

2012 ◽  
Vol 51 (10S) ◽  
pp. 10NF08 ◽  
Author(s):  
Takahiro Kato ◽  
Takuma Miyake ◽  
Daisuke Tashima ◽  
Tatsuya Sakoda ◽  
Masahisa Otsubo ◽  
...  
Keyword(s):  
Power Control ◽  
Output Power ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Solar Panel ◽  
Maximum Output

Performance Study of GaAs Photovoltaic Power Converter in Optically Powered Systems

2014 ◽  
Vol 556-562 ◽  
pp. 1894-1897
Author(s):  
Xin Wei Yuan ◽  
Jie Qin Shi
Keyword(s):  
Short Circuit ◽  
Electrical Power ◽  
Maximum Output Power ◽  
Optical Power ◽  
Short Circuit Current ◽  
Power Converter ◽  
Open Circuit ◽  
Maximum Output ◽  
Performance Study ◽  
Photovoltaic Power

Optically powered system is a revolutionary new power delivery system, in which optical power is delivered over fiber to photovoltaic power converter, where optical power is transformed into electrical power. Therefore the system is inherently immune to RF, EMI, high voltage and lighting effects. Capable of powering electronic circuitry by optical fiber, this technology has been validated in industries such as electric power, communications, remote sensing and aerospace. To a large extent, photovoltaic power converter is a key component that decides the performance of optically powered system. In this paper, the commonly used GaAs photovoltaic power converter is studied and tested. Parameter values like open circuit voltage, short circuit current, maximum output power, conversion efficiency and the optimum load resistance are obtained through experiment, which can be severed as important reference while choosing or designing DC-DC converter.

Maximum Output Power Control Using Short-Circuit Current and Open-Circuit Voltage of a Solar Panel

2012 ◽  
Vol 51 ◽  
pp. 10NF08
Author(s):  
Takahiro Kato ◽  
Takuma Miyake ◽  
Daisuke Tashima ◽  
Tatsuya Sakoda ◽  
Masahisa Otsubo ◽  
...  
Keyword(s):  
Power Control ◽  
Output Power ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Solar Panel ◽  
Maximum Output

scholarly journals Investigation of Position Sensing and Energy Harvesting of a Flexible Triboelectric Touch Pad

Nanomaterials ◽  
2018 ◽  
Vol 8 (8) ◽  
pp. 613 ◽  
Author(s):  
Tao Chen ◽  
Qiongfeng Shi ◽  
Kunpu Li ◽  
Zhan Yang ◽  
Huicong Liu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Short Circuit ◽  
Electronic Devices ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Triboelectric Nanogenerator ◽  
Maximum Output ◽  
Current Output ◽  
Position Sensing

Triboelectric nanogenerator (TENG) is a promising technology because it can harvest energy from the environment to enable self-sustainable mobile and wearable electronic devices. In this work, we present a flexible touch pad capable of detecting the contact location of an object and generating substantial energy simultaneously based on the coupling of triboelectric effects and electrostatic induction. The touch pad consists of Polytetrafluoroethylene (PTFE) thin film, multiple Aluminum (Al) electrodes and Polyethylene terephthalate (PET) layers, which can be achieved through low cost, simplified and scalable fabrication process. Different from the conventional multi-pixel-based positioning sensor (i.e., large array of sensing elements and electrodes), the analogue method proposed here is used to implement the positioning function with only four electrodes. Position location can achieve a detecting resolution of as small as 1.3 mm (the size of locating layer is 7.5 cm × 7.5 cm). For the energy harvesting part, a multilayer structure is designed to provide higher current output. The open circuit voltage of the device is around 420 V and the short circuit current can reach up to 6.26 µA with current density of 0.25 µA/cm2. The maximum output power obtained is approximately 10 mW, which is 0.4 mW/cm2. The flexibility and significantly reduced number of electrodes enable the proposed touch pad to be readily integrated into portable electronic devices, such as intelligent robots, laptops, healthcare devices, and environmental surveys, etc.

scholarly journals Fabrication and Optoelectrical Properties of IZO/Cu2OHeterostructure Solar Cells by Thermal Oxidation

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Cheng-Chiang Chen ◽  
Lung-Chien Chen ◽  
Yi-Hsuan Lee
Keyword(s):  
Solar Cells ◽  
Fill Factor ◽  
Open Circuit Voltage ◽  
Low Cost ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Maximum Output ◽  
Indium Zinc Oxide

Indium zinc oxide (IZO)/cupper oxide (Cu2O) is a nontoxic nature and an attractive all-oxide candidate for low-cost photovoltaic (PV) applications. The present paper reports on the fabrication of IZO/Cu2O heterostructure solar cells which the Cu2O layers were prepared by oxidation of Cu thin films deposited on glass substrate. The measured parameters of cells were the short-circuit current (Isc), the open-circuit voltage (Voc), the maximum output power (Pm), the fill factor (FF), and the efficiency (η), which had values of 0.11 mA, 0.136 V, 5.05 μW, 0.338, and 0.56%, respectively, under AM 1.5 illumination.

scholarly journals The Effect of Temperature on the Solar Cell Efficiency, Output Currents and Voltages

2021 ◽  
Vol 13 (2) ◽  
pp. 55
Author(s):  
Asim Ahmed Mohamed Fadol ◽  
Mohammed M. Rashed ◽  
L. M. Abdalgadir ◽  
Essam E. Ali
Keyword(s):  
Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Effect Of Temperature ◽  
Maximum Output ◽  
Current Increase ◽  
Increasing Temperature

Experimental results shows that all electrical parameters of solar cell such as maximum output power, open circuit voltage, short circuit current, and fill factor beside efficiency have been changed with temperature. According to results, the most significant is the temperature dependence of the voltage which decreases with increasing temperature while the current of cells slightly increases by temperature. The fill factor and the efficiency decrease upon increasing temperature. This confirms the fact that the voltage decrease is more significant than the current increase.

Design and Simulation of a Novel Thermoelectric Micro-Device with Electrodeposited Bi-Te Alloys

2018 ◽  
Vol 281 ◽  
pp. 788-794
Author(s):  
S. Guo ◽  
Ning Su ◽  
Fu Li ◽  
Da Wei Liu ◽  
Bo Li
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Output Power ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Convection Heat Transfer ◽  
Open Circuit ◽  
Maximum Output ◽  
Transfer Coefficients

A novel thermoelectric micro-device was designed with n-type and p-type Bi-Te materials alloys via a template electrodeposition process. The glass template including 250 holes in 10×10 mm2with a thickness of 200~ 400 µm. The diameter of the holes is 50~ 80 µm and the distance of adjacent centers of the holes is 200 µm. According to the design, the performance of heat transference and thermoelectric energy generation are simulated by COMSOL Multiphysics. In order to simplify model, there are 16 units in total, and each unit is made up of 16 (4 × 4) pillars. In the simulation, the largest temperature difference is 7.8K on the conditions of 500 W/m2K in convection heat transfer coefficients and the maximum output potential of the module is 21.7 mV. The maximum output power achieved 96.9 µW under 500 W/m2K of heat transfer coefficient and 10 mA of current. Under ideal conditions, the value of open circuit voltage and maximum output power increases to nine times as the model, but short circuit current remains the same. When the heat transfer coefficient is 500 W/m2K and the current density is 10 mA, the maximum output power of the actual product achieved 871.7 µW.

Output Characteristics Study of V-trough PV Concentration System

2011 ◽  
Vol 71-78 ◽  
pp. 2077-2080 ◽  
Author(s):  
Cui Qiong Yan
Keyword(s):  
Output Power ◽  
Short Circuit ◽  
Maximum Output Power ◽  
Open Circuit ◽  
Maximum Output ◽  
Water Cooling ◽  
Cell Array ◽  
Pv System ◽  
Current Output ◽  
Super Cell

A V-trough PV system with polysilicon cell array and super cell array has been constructed and tested. Open-circuit voltage, short-circuit current, output power, fill factor and influence of temperature on V-trough PV concentration system have been analyzed. The results indicate that the output power of 10 pieces of polysilicon cell array is 6.198W and it is 1.21 times as that of non-concentration condition. Maximum output power of V-trough PV system with water cooling increase to 8.28W and power increment rate reach 62.67% compared with the non-concentration PV system. For the super cell array with no water cooling, the maximum output power of V-trough PV system varies from 7.834W to 14.223W. The results of this work provide some experimental support to the applications of the V-trough PV system.

EXPERIMENTAL INVESTIGATION ON CHARACTERISTICS OF LOW-CONCENTRATING SOLAR CELLS

2011 ◽  
Vol 25 (09) ◽  
pp. 679-684 ◽  
Author(s):  
W. B. XIAO ◽  
X. D. HE ◽  
J. T. LIU ◽  
Y. Q. GAO
Keyword(s):  
Solar Cells ◽  
Light Intensity ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Incident Light ◽  
Short Circuit Current ◽  
Light Level ◽  
Spot Size ◽  
Internal Resistance ◽  
Open Circuit

At room temperature, the performance of low-concentrating solar cells is investigated experimentally and discussed by theory. The results show that the short-circuit current, which is larger than that of unconcentrated radiation, linearly increases with the light intensity and is directly proportional to the concentration ratio. However, the different behavior is obtained for the open-circuit voltage. The open-circuit voltage is also larger than that at the unconcentrated light level and follows a logarithmic function of the light intensity, showing almost no dependence on the concentration ratios. The main reason is the decrease in internal resistance of solar cell with decreasing spot size, because the increase of incident light intensity leads to an increase of current density. Therefore, an advantage of the low-concentrating photovoltaic systems results from the improvement of the short-circuit current, but not from the open-circuit voltage. This work is very significant for the design of low-concentrating system.

scholarly journals Concentrating System’s Design and Performance Analysis for Spacial Solar Array

2018 ◽  
Vol 36 (3) ◽  
pp. 471-479
Author(s):  
Limin Shao ◽  
Shuli Yang
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Output Power ◽  
Open Circuit Voltage ◽  
Operating Temperature ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Solar Array ◽  
Maximum Output

A large area of sunlight onto solar cells is gathered by concentrating system for spacial concentrating solar array, which reduces the amount of solar cells by increasing light intensity onto the solar cells of the unit area. Under concentrating conditions, the short-circuit current, open-circuit voltage, fill factor, efficiency, operating temperature and strong thermal-electrical coupling characteristics of concentrating solar cells are different from the conventional solar cells because of the high intensity and high operating temperature. The concentrating module design, solar cell selection, and design of solar cell heat-dissipation have been carried out. The thermal-electric coupling model of special concentrating photovoltaic system has been established. The relationships among concentrated ratio, substrate-thickness, thermal conductivity of substrate-material and solar cell’s temperature, density of short-circuit current, open-circuit voltage, maximum output power have been analyzed, which provide a view to a reasonabl0e match and selection of multi-parameters in engineering design. Results show that the concentrated ratio has an overall effect on the open-circuit voltage, short-circuit current, efficiency and operating temperature of the solar cell. There is a strong coupling relationship among the parameters, and the positive and negative impacts caused by the concentrating characteristics should be weighed in the engineering design. The short-circuit current density of concentrating solar cells is proportional to the concentrated ratio. Under the lower concentrated ratio circumstance, fill factor and efficiency is not substantially affected by the concentrated ratio. The maximum output power and open-circuit voltage increase with the increase of concentrated ratio. Temperature of concentrating solar cells has an adverse effect on the open-circuit voltage, efficiency and output power, which needs high efficient radiator measures to be taken. The operating temperature of solar cells could be decreased significantly by the high thermal conductivity of the substrate-material. The concentrated ratio between 9~15 is recommended for spacial solar array, which not only embodies the advantage of concentrator like improving the cell-efficiency and decreasing the cost, but also doesn’t exact the deploying precision of concentrating system.

Sign in / Sign up

Export Citation Format

Share Document