scholarly journals Thermal–Hydraulic Performance in a Microchannel Heat Sink Equipped with Longitudinal Vortex Generators (LVGs) and Nanofluid

Processes ◽  
2020 ◽  
Vol 8 (2) ◽  
pp. 231
Author(s):  
Basel AL Muallim ◽  
Mazlan A. Wahid ◽  
Hussein A. Mohammed ◽  
Mohammed Kamil ◽  
Daryoush Habibi
Keyword(s):  
Nusselt Number ◽  
Friction Factor ◽  
Heat Sink ◽  
Pure Water ◽  
Hydraulic Performance ◽  
Vortex Generators ◽  
Longitudinal Vortex ◽  
Working Fluid ◽  
Microchannel Heat Sink ◽  
Fanning Friction Factor

In this study, the numerical conjugate heat transfer and hydraulic performance of nanofluids flow in a rectangular microchannel heat sink (RMCHS) with longitudinal vortex generators (LVGs) was investigated at different Reynolds numbers (200–1200). Three-dimensional simulations are performed on a microchannel heated by a constant temperature with five different configurations with different angles of attack for the LVGs under laminar flow conditions. The study uses five different nanofluid combinations of Al2O3 or CuO, containing low volume fractions in the range of 0.5% to 3.0% with various nanoparticle sizes that are dispersed in pure water, PAO (Polyalphaolefin) or ethylene glycol. The results show that for Reynolds number ranging from 100 to 1100, Al2O3–water has the best performance compared with CuO nanofluid with Nusselt number values between 7.67 and 14.7, with an associated increase in Fanning friction factor by values of 0.0219–0.095. For the case of different base fluids, the results show that CuO–PAO has the best performance with Nusselt number values between 9.57 and 15.88, with an associated increase in Fanning friction factor by 0.022–0.096. The overall performance of all configurations of microchannels equipped with LVGs and nanofluid showed higher values than the ones without LVG and water as a working fluid.

scholarly journals Heat transfer and entropy generation in a microchannel with longitudinal vortex generators using Nanofluids

2020 ◽  
Author(s):  
Amin Ebrahimi ◽  
Farhad Rikhtegar Nezami ◽  
Amin Sabaghan ◽  
Ehsan Roohi
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Single Phase ◽  
Pure Water ◽  
Vortex Generators ◽  
Longitudinal Vortex ◽  
Working Fluid ◽  
Two Phase ◽  
Rectangular Microchannel ◽  
Important Conclusion

Conjugated heat transfer and hydraulic performance for nanofluid flow in a rectangular microchannel heat sink with LVGs (longitudinal vortex generators) are numerically investigated using at different ranges of Reynolds numbers. Three-dimensional simulations are performed on a microchannel heated by a constant heat flux with a hydraulic diameter of 160 μm and six pairs of LVGs using a single-phase model. Coolants are selected to be nanofluids containing low volume-fractions (0.5%–3.0%) of Al2O3 or CuO nanoparticles with different particle sizes dispersed in pure water. The employed model is validated and compared by published experimental, and single-phase and two-phase numerical data for various geometries and nanoparticle sizes. The results demonstrate that heat transfer is enhanced by 2.29–30.63% and 9.44%–53.06% for water-Al2O3 and water-CuO nanofluids, respectively, in expense of increasing the pressure drop with respect to pure-water by 3.49%–16.85% and 6.5%–17.70%, respectively. We have also observed that the overall efficiency is improved by 2.55%–29.05% and 9.78%–50.64% for water-Al2O3 and water-CuO nanofluids, respectively. The results are also analyzed in terms of entropy generation, leading to the important conclusion that using nanofluids as the working fluid could reduce the irreversibility level in the rectangular microchannel heat sinks with LVGs. No exterma (minimums) is found for total entropy generation for the ranges of parameters studied.

Numerical Study of Flow and Heat Transfer in Rectangular Channel With Periodic Longitudinal Vortex Generators Under Pulsating Flow

2012 ◽  
Author(s):  
Lin Tian ◽  
Wei Bai ◽  
Shanhu Xue ◽  
Zipeng Huang ◽  
Qiuwang Wang
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Factor ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Vortex Generators ◽  
Longitudinal Vortex ◽  
Small Scale ◽  
Inlet Velocity ◽  
Flow And Heat Transfer

The unsteady turbulent flow and heat transfer in rectangular channel with periodic longitudinal vortex generators on up and bottom walls are investigated by standardized k-ε two equation turbulent model combined with standardized wall function which has been validated by steady experimental data. Influence of varying frequency and amplitude of inlet velocity varying by sine function on heat transfer and friction factor are discussed. It is found that parameters such as Tout, Tf, Tw, Nusselt number and the friction factor f vary with time periodically, phase difference occurred compared with inlet velocity. Pulsating frequency has little impact on time averaged Nusselt number. However, when amplitude increases from 0.2us to 0.8us, the heat transfer rate is augmented by about 4%. Furthermore, a critical frequency has been captured when amplitude equals to 0.8us for the channel studied. The current study will deepen understanding of unsteady flow in plate fuel assembly, which can be used in small-scale reactors.

Thermal and Hydraulic Performances of Porous Microchannel Heat Sink using Nanofluids

2021 ◽  
pp. 1-32
Author(s):  
Zahir Uddin Ahmed ◽  
Md. Roni Raihan ◽  
Omidreza Ghaffari ◽  
Muhammad Ikhlaq
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Friction Factor ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Heat Sink ◽  
Hydraulic Performance ◽  
Microchannel Heat Sink ◽  
Nanoparticle Concentration

Abstract Microchannel heat sink is an effective method in compact and faster heat transfer applications. This paper numerically investigates thermal and hydraulic characteristics of a porous microchannel heat sink (PMHS) using various nanofluids. The effect of porosity, inlet velocity and nanoparticle concentration on thermal-hydraulic performance is systematically examined. The result shows a significant temperature increase (40°C) of the coolant in the porous zone. The pressure drop reduces by 35% for γ = 0.32 compared to the non-porous counterpart, and this reduction of pressure significantly continues when γ further increases. The pressure drop with win is linear for PMHS with nanofluids, and the change in pressure drop is steeper for nanofluids compared to their base fluids. The average heat transfer coefficients increases about 2.5 times for PMHS, and a further increase of 6% in is predicted with the addition of nanoparticle. The average Nusselt number increases non-linearly with Re for PMHS. The friction factor reduces by 50% when γ increases from 0.32 to 0.60, and the effect of nanofluid on friction factor is insignificant beyond the mass flow rate of 0.0004 kg/s. Whilst Cu and CuO nanoparticles help to dissipate the larger amount of heat from the microchannel, Al2O3 nanoparticle appears to have a detrimental effect on heat transfer. The thermal-hydraulic performance factor strongly depends on the nanoparticles, and it slightly decreases with the mass flow rate. The increase of nanoparticle concentration, in general, enhances both h and ΔP linearly for the range considered.

scholarly journals The Thermal Hydraulic Performance of Wavy PCHE with Different Materials and Geometric Parameters

2018 ◽  
Vol 207 ◽  
pp. 04008
Author(s):  
Yunzhu Li ◽  
Yonghui Xie ◽  
Di Zhang
Keyword(s):  
Nusselt Number ◽  
Friction Factor ◽  
Hydraulic Performance ◽  
Geometric Parameters ◽  
Straight Channel ◽  
Wavy Channel ◽  
Computational Fluid Dynamics Cfd ◽  
Grade 3 ◽  
Titanium Grade ◽  
Fanning Friction Factor

The printed circuited heat exchanger (PCHE) contain several different channel configurations, such as straight channel, zigzag channel and wavy channel. The wavy channel has better thermal performance than the straight channel and better hydraulic performance than the zigzag channel. This paper explores the thermal hydraulic performance of wavy channel PCHE. The numerical analysis of the PCHE in different materials and geometric parameters are conducted by computational fluid dynamics (CFD) tool. The materials applied in simulations involve Alloy617, Titanium Grade 3, Carlson 2205, UNS S30400 and Sandvik 253A. The results show that the materials have little effect on the thermal-hydraulic performance. The geometric parameters include channel degree varying from 10°to 50°, channel amplitude varying from 1mm to 5mm and the radium of hot/cold channel varying from 0.4mm to 2.0mm. It is found that the larger radium of hot channel results out the lower Nusselt number and lower fanning-friction factor while the higher radium of cold channel produces the higher Nusselt number and lower fanning-friction factor. The larger channel amplitude indicates the higher fanning-friction factor and lower Nusselt number. The larger channel degree indicates the higher fanning-friction factor, and higher Nusselt number.

Thermo-hydraulic performance of modified plate fin and pin fin heat sinks

2021 ◽  
pp. 095765092110240
Author(s):  
Anil Kumar Patil ◽  
Vishwjeet Choudhary ◽  
Ayush Gupta ◽  
Manoj Kumar
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Factor ◽  
Heat Sink ◽  
Hydraulic Performance ◽  
Heat Sinks ◽  
Forced Flow ◽  
Transfer Rates ◽  
Pin Fin ◽  
Pitch Ratio

Extended surfaces are widely investigated for their ability to enhance the heat transfer rates in different applications. Pin-fin and plate-fin heat sinks are used in a variety of cases involving a miniaturized to the large systems. The present study compares the performance of the pin-fin and the plate-fin heat sink under similar forced flow conditions. The experimental data for a modified pin fin heat sink with wings and a plate-fin heat sink with dimples are collected for the Reynolds number in the range of 6800–15100. The Nusselt number, friction factor, and thermo-hydraulic performance (THP) are examined for different geometries of the heat sink and the enhancements brought out in the heat transfer and friction are gauged relative to the smooth plate. The pin fin heat sink yields two-fold enhancement in heat transfer as compared to the plate-fin heat sink. The maximum thermo-hydraulic performance of the pin-fin heat sink with wings is found to be 4.52 at a pitch ratio (S/Df) of 2 and Wing length ratio (Lw/Df). For the plate fin heat sink with dimples, the maximum thermo-hydraulic performance is found to be 4.67 at dimple diameter ratio (D/d) of 0.5 and dimple pitch ratio (s/d) of 2.5. The correlations of the Nusselt number and friction factor are proposed for different geometries of fins.

Development of MEMS Microchannel Heat Sinks for Micro/Nano Spacecraft Thermal Control

2002 ◽  
Author(s):  
Anthony D. Paris ◽  
Gajanana C. Birur ◽  
Amanda A. Green
Keyword(s):  
Heat Sink ◽  
Thermal Control ◽  
Hydraulic Performance ◽  
Heat Sinks ◽  
Performance Criteria ◽  
Working Fluid ◽  
High Heat Flux ◽  
Microchannel Heat Sink ◽  
Microchannel Heat Sinks ◽  
Spacecraft Thermal Control

MEMS-based microchannel heat sinks are being investigated at the Jet Propulsion Laboratory (JPL) for use in micro/nano spacecraft thermal control. The current stage of development focuses on the integration of microchannel heat sinks into spacecraft pumped cooling loops. Two microchannel heat sinks, adapted from a Stanford University Microfluidics Laboratory design, were fabricated at JPL and tested for thermal and hydraulic performance in a single-phase pumped cooling loop. The first microchannel heat sink design was demonstrated to remove heat fluxes of up to 25 W/cm2 with a maximum device temperature of less than 80 °C. Both the original and redesigned heat sinks where shown to meet hydraulic performance criteria requiring less than 1 psi pressure drop with water as the working fluid. It was concluded that the design methodology developed for this project produces microchannel heat sink devices capable of high heat flux removal in future micro/nano spacecraft thermal control architecture.

scholarly journals Optimization of a Wavy Microchannel Heat Sink with Grooves

Processes ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 373
Author(s):  
Min-Cheol Park ◽  
Sang-Bum Ma ◽  
Kwang-Yong Kim
Keyword(s):  
Thermal Resistance ◽  
Friction Factor ◽  
Heat Sink ◽  
Latin Hypercube Sampling ◽  
Groove Depth ◽  
Working Fluid ◽  
Microchannel Heat Sink ◽  
Factorial Method ◽  
Design Variables ◽  
Full Factorial

In this study, a wavy microchannel heat sink with grooves using water as the working fluid is proposed for application to cooling microprocessors. The geometry of the heat sink was optimized to improve heat transfer and pressure loss simultaneously. To achieve optimization goals, the average friction factor and thermal resistance were used as the objective functions. Three dimensionless parameters were selected as design variables: the distance between staggered grooves, groove width, and groove depth. A modified Latin hypercube sampling (LHS) method that combines the advantages of conventional LHS and a three-level full factorial method is also proposed. Response surface approximation was used to construct surrogate models, and Pareto-optimal solutions were obtained with a multi-objective genetic algorithm. The modified LHS was proven to have better performance than the conventional LHS and full factorial methods in the present optimization problem. A representative optimal design showed that both the thermal resistance and friction factor improved by 1.55% and 3.00%, compared to a reference design, respectively.

Two-Phase Flow in Microchannels

2001 ◽  
Author(s):  
G. Hetsroni ◽  
A. Mosyak ◽  
Z. Segal
Keyword(s):  
Heat Sink ◽  
High Speed ◽  
Single Phase ◽  
Flow Boiling ◽  
Electronics Cooling ◽  
Working Fluid ◽  
Microchannel Heat Sink ◽  
Two Phase ◽  
Infrared Radiometry ◽  
Phase Water

Abstract Experimental investigation of a heat sink for electronics cooling is performed. The objective is to keep the operating temperature at a relatively low level of about 323–333K, while reducing the undesired temperature variation in both the streamwise and transverse directions. The experimental study is based on systematic temperature, flow and pressure measurements, infrared radiometry and high-speed digital video imaging. The heat sink has parallel triangular microchannels with a base of 250μm. According to the objectives of the present study, Vertrel XF is chosen as the working fluid. Experiments on flow boiling of Vertrel XF in the microchannel heat sink are performed to study the effect of mass velocity and vapor quality on the heat transfer, as well as to compare the two-phase results to a single-phase water flow.

Sign in / Sign up

Export Citation Format

Share Document