scholarly journals Longest-Range UHF RFID Sensor Tag Antenna for IoT Applied for Metal and Non-Metal Objects

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5460 ◽  
Author(s):  
Franck Kimetya Byondi ◽  
Youchung Chung
Keyword(s):  
Wireless Sensor Networks ◽  
Radio Frequency Identification ◽  
High Frequency ◽  
Wireless Sensor ◽  
The Internet ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Frequency Identification ◽  
The Internet Of Things ◽  
Read Range

This paper presents a passive cavity type Ultra High Frequency (UHF) Radio Frequency Identification (RFID) tag antenna having the longest read-range, and compares it with existing long-range UHF RFID tag antenna. The study also demonstrates mathematically and experimentally that our proposed longest-range UHF RFID cavity type tag antenna has a longer read-range than existing passive tag antennas. Our tag antenna was designed with 140 × 60 × 10 mm3 size, and reached 26 m measured read-range and 36.3 m mathematically calculated read-range. This UHF tag antenna can be applied to metal and non-metal objects. By adding a further sensing capability, it can have a great benefit for the Internet of Things (IoT) and wireless sensor networks (WSN).

scholarly journals Problems of Powering End Devices in Wireless Networks of the Internet of Things

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2417
Author(s):  
Andrzej Michalski ◽  
Zbigniew Watral
Keyword(s):  
Wireless Sensor Networks ◽  
Sensor Networks ◽  
Internet Of Things ◽  
Radio Frequency Identification ◽  
Wireless Sensor ◽  
Alternative Possibilities ◽  
The Internet ◽  
Power Sources ◽  
Wide Range ◽  
The Internet Of Things

This article presents the problems of powering wireless sensor networks operating in the structures of the Internet of Things (IoT). This issue was discussed on the example of a universal end node in IoT technology containing RFID (Radio Frequency Identification) tags. The basic methods of signal transmission in these types of networks are discussed and their impact on the basic requirements such as range, transmission speed, low energy consumption, and the maximum number of devices that can simultaneously operate in the network. The issue of low power consumption of devices used in IoT solutions is one of the main research objects. The analysis of possible communication protocols has shown that there is a possibility of effective optimization in this area. The wide range of power sources available on the market, used in nodes of wireless sensor networks, was compared. The alternative possibilities of powering the network nodes from Energy Harvesting (EH) generators are presented.

A Novel Design of PIE Decoding with Multiple CRC Circuit for RFID Tag

2013 ◽  
Vol 816-817 ◽  
pp. 957-961
Author(s):  
Feng Ying Huang ◽  
Jun Wang ◽  
Yu Sen Xu ◽  
Ji Wei Huang
Keyword(s):  
Data Processing ◽  
Parallel Algorithm ◽  
Radio Frequency Identification ◽  
High Frequency ◽  
Pulse Interval ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Frequency Identification ◽  
Simulation Results ◽  
Novel Design

This paper proposes a new synchronized serial-parallel CRC(Cycle Redundancy Check) with PIE(Pulse Interval Encoding) decoding circuit for the UHF(Ultra-High Frequency) RFID(Radio Frequency Identification), which is based on the ISO/IEC 18000-6C standards protocol. The parallel algorithm of CRC circuit is derived, and the serial or parallel CRC circuit on RFID tag chip is evaluated in this paper. Finally, the designed circuit is simulated and analyzed on the FPGA platform. Simulation results show that the proposed circuit meets the communication requirement of the protocol and addresses the problem of low data processing rate of conventional serial CRC circuit, as well as implements 1 to 8 degree of parallelism of the parallel CRC circuit for UHF RFID.

RFID Tag Area Management Base on IOT

2013 ◽  
Vol 756-759 ◽  
pp. 4529-4532 ◽  
Author(s):  
Hao Zeng ◽  
Yan Hui Fu ◽  
Xu Chen
Keyword(s):  
Internet Of Things ◽  
Radio Frequency ◽  
Radio Frequency Identification ◽  
The Internet ◽  
Rfid Tag ◽  
Frequency Identification ◽  
The Right ◽  
The Internet Of Things ◽  
Area Management

Traditional Radio Frequency Identification (RFID) Tag Equipment has some problems like these: it is difficult to realize if the tag is kept out, destroyed, or taken away abnormally. It cant accurately judge where the area the tag had moved to is. Besides, it is difficult to distinguish the right of the tag in the Tag Management. To solve these issues, this paper serves with a method which is based on the Internet of Things (IOT). It mainly includes as the following: the tag is activated in the Controlled Area, the judgment of the tag access the Controlled Area, whether the tag exists in the Controlled Area or not. These methods can reform the problems that the Traditional RFID Tag Equipment has.

scholarly journals Energy Harvesting Techniques for Wireless Sensor Networks/Radio-Frequency Identification: A Review

Symmetry ◽  
2019 ◽  
Vol 11 (7) ◽  
pp. 865 ◽  
Author(s):  
Mohammed H. Alsharif ◽  
Sunghwan Kim ◽  
Nuri Kuruoğlu
Keyword(s):  
Wireless Sensor Networks ◽  
Sensor Networks ◽  
Radio Frequency ◽  
Radio Frequency Identification ◽  
Critical Issue ◽  
Security And Privacy ◽  
Wireless Sensor ◽  
The Internet ◽  
Heterogeneous Objects ◽  
Frequency Identification

In the near future, symmetry technologies for the Internet of Things (IoT), along with symmetry and asymmetry applications for IoT security and privacy, will re-design the socio-ecological human terrain morphology. The IoT ecosystem deploys diverse sensor platforms connecting billions of heterogeneous objects through the Internet. Most sensors are low-energy consuming devices which are designed to transmit sporadically or continuously. However, when we consider the billions/trillions of connected sensors powering various user applications, their energy efficiency (EE) becomes a critical issue. Therefore, the importance of EE in IoT technology cannot be overemphasised, specifically the development of EE solutions for sustainable IoT technology. Propelled by this need, EE proposals are expected to address IoT’s EE issues. Consequently, many developments have been displayed, and highlighting them to provide clear insights into eco-sustainable and green IoT technologies is becoming a crucial task. To pursue a clear vision of green IoT, this article aims to describe the current state-of-the art insights into energy-saving practices and strategies on green IoT. The major contribution of this study is the review and discussion of the substantial issues enabling hardware green IoT to focus on green wireless sensor networks and green radio-frequency identification. This review paper will contribute significantly to the future implementation of green and eco-sustainable IoT.

scholarly journals Different Substrate Materials for Designing a Passive UHF RFID Tag Antenna

2019 ◽  
Vol 8 (9S) ◽  
pp. 572-580 ◽  
Keyword(s):  
Radio Frequency Identification ◽  
Impedance Matching ◽  
Dipole Antenna ◽  
Antenna Gain ◽  
Rfid Technology ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Passive Uhf Rfid ◽  
Frequency Identification ◽  
Read Range

The Radio Frequency Identification (RFID) technology has been increasingly used for various application such as tracking of products, smart cards, identification, item management, security etc. In this paper, the performance parameter of the passive UHF RFID tag antenna has been studied for four different substrate materials viz., FR4 epoxy, PET, Rogers 4350, Taconic TLY materials. A simple meandered dipole antenna has been designed using a T-match stub for impedance matching of the tag antenna with the attached RFID chip. These different substrates are then designed separately, for the same antenna geometry. The effect of using these substrates on RFID tag antenna parameters such as reflection coefficient, antenna gain, VWSR, radiation pattern, impedance, ease of optimization level, read range, and radiation efficiency are then observed.

scholarly journals Flexible Radio-Frequency Identification (RFID) Tag Antenna for Sensor Applications

Sensors ◽  
2018 ◽  
Vol 18 (12) ◽  
pp. 4212 ◽  
Author(s):  
Mohammad Islam ◽  
Touhidul Alam ◽  
Iskandar Yahya ◽  
Mengu Cho
Keyword(s):  
Radio Frequency ◽  
Radio Frequency Identification ◽  
Low Cost ◽  
System Level ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Sensor Applications ◽  
Frequency Identification ◽  
Flexible Radio ◽  
Read Range

In this paper, an inkjet-printed flexible Radio-Frequency Identification (RFID) tag antenna is proposed for an ultra-high frequency (UHF) sensor application. The proposed tag antenna facilitates a system-level solution for low-cost and faster mass production of RFID passive tag antenna. The tag antenna consists of a modified meander line radiator with a semi-circular shaped feed network. The structure is printed on photo paper using silver nanoparticle conductive ink. The generic design outline, as well as tag antenna performances for several practical application aspects are investigated. The simulated and measured results verify the coverage of universal UHF RFID band with an omnidirectional radiation pattern and a long-read range of 15 ft. In addition, the read range for different bending angles and lifetimes of the tag antenna are also demonstrated.

scholarly journals Integrating Passive UHF RFID Tags with WSN Nodes: Challenges and Opportunities

2014 ◽  
Vol 10 (2) ◽  
pp. 99 ◽  
Author(s):  
Luigi Patrono
Keyword(s):  
Radio Frequency Identification ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Passive Uhf Rfid ◽  
Integration Approach ◽  
Challenges And Opportunities ◽  
Class 1 ◽  
Frequency Identification ◽  
New Generation ◽  
The Internet Of Things

Radio Frequency Identification (RFID) and Wireless Sensor Networks (WSNs) have received an ever-increasing attention in recent years, mainly because they represent two of the most important technologies enabling the Internet of Things vision. Although designed originally with different objectives, WSN and RFID represent two complementary technologies whose integration might increase their functionalities and extend their range of applications. However, important technological issues must still be solved in order to fully exploit the potentialities offered by such integration. In this work, an innovative RFID-WSN integration approach is presented and validated. It relies on the interconnection of a new-generation, long-range, EPCglobal Class-1 Generation-2 Ultra-High-Frequency (UHF) RFID tag with a commercial WSN node via the I2C interface. Experimental results have demonstrated the effectiveness of the proposed approach compared to existing solution in the literature. Interesting application scenarios enabled by the proposed RFID-WSN integration approach are briefly summarized at the end of the paper.

scholarly journals Inkjet printed nanomaterial based flexible radio frequency identification (RFID) tag sensors for the internet of nano things

RSC Advances ◽  
2017 ◽  
Vol 7 (77) ◽  
pp. 48597-48630 ◽  
Author(s):  
Ravina Singh ◽  
Eric Singh ◽  
Hari Singh Nalwa
Keyword(s):  
Internet Of Things ◽  
Radio Frequency ◽  
Radio Frequency Identification ◽  
The Internet ◽  
Daily Lives ◽  
Rfid Tag ◽  
Entire Spectrum ◽  
Frequency Identification ◽  
The Internet Of Things ◽  
Flexible Radio

The Internet of Things (IoT) has limitless possibilities for applications in the entire spectrum of our daily lives, from healthcare to automobiles to public safety.

scholarly journals UHF RFID Conductive Fabric Tag Design Optimization

Sensors ◽  
2021 ◽  
Vol 21 (16) ◽  
pp. 5380
Author(s):  
Franck Kimetya Byondi ◽  
Youchung Chung
Keyword(s):  
Radio Frequency Identification ◽  
High Frequency ◽  
Network Analyzer ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Conductive Fabric ◽  
Direct Current Resistance ◽  
Frequency Identification ◽  
Matching Structure ◽  
Current Resistance

This paper presents the design of a 920 MHz Ultra High Frequency (UHF) band radio frequency identification (RFID) conductive fabric tag antenna. The DC (Direct Current) resistance and impedance of the conductive fabric are measured by a DC multimeter and by a network analyzer at a UHF frequency band. The conductivities of the fabrics are calculated with their measured DC resistance and impedance values, respectively. The conductivities of the fabric are inserted into the CST simulation program to simulate the fabric tag antenna designs, and the results of the tag designs with two conductivities are compared. Two fabric UHF RFID tag antennas with a T-Matching structure, one with the name-tag size of 80 × 40 mm, and another with 40 × 23 are simulated and measured the characteristics of tag antennas. The simulated and measured results are compared by reflection coefficient S11, radar cross-section and reading range. The reading range of the 80 × 40 mm fabric tag antenna is about 4 m and 0.5 m for the 40 × 23 size tag. These fabric tags can be easily applied to an entrance control system as they can be attached to other fabrics and clothes.

scholarly journals Long-Range UHF RFID Tag for Automotive License Plate

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2521
Author(s):  
Youchung Chung ◽  
Teklebrhan H. Berhe
Keyword(s):  
Radiation Pattern ◽  
Radio Frequency Identification ◽  
High Frequency ◽  
License Plate ◽  
Back Side ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Antenna Type ◽  
Frequency Identification ◽  
Em Simulation

In this paper, various locations of an Ultra High Frequency (UHF) Radio Frequency Identification (RFID) tag on automotive license plates have been considered based on the radiation pattern of the tag antenna. A small, 130 × 50 mm, passive loop antenna type UHF RFID tag for an automotive license plate was simulated with an EM simulation CST program. It was designed to have a larger back-lobe radiation pattern since the front side of the tag faces the back side of the plate holder to protect the tag antenna from bugs and dust when the automobile runs. The tag was attached to the side of a license plate holder with a dimension of 520 × 110 mm, the typical size of the standard license plate. The reflection coefficient of the tag antenna is −21 dB at 920 MHz, and the gain of the tag antenna is 6.29 dBi at the back-lobe. The reading range of the tag antenna with the plate holder, which was measured in an open field, is about 10.3 m, and the reading range of the tag installed on the bumper from the front of the vehicle is 9.4 m. The tag antenna is small enough to apply to a real automobile, and it is applicable because it uses the back-lobe pattern, so it does not require an extra device for protection from damage.

Sign in / Sign up

Export Citation Format

Share Document