scholarly journals Low Cost, Easy to Prepare and Disposable Electrochemical Molecularly Imprinted Sensor for Diclofenac Detection

Sensors ◽  
2021 ◽  
Vol 21 (6) ◽  
pp. 1975
Author(s):  
Isabel Seguro ◽  
João G. Pacheco ◽  
Cristina Delerue-Matos
Keyword(s):  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Tap Water ◽  
Low Cost ◽  
Differential Pulse ◽  
Portable Devices ◽  
Molecularly Imprinted ◽  
Selective Determination ◽  
Mip Sensor

In this work, a disposable electrochemical (voltammetric) molecularly imprinted polymer (MIP) sensor for the selective determination of diclofenac (DCF) was constructed. The proposed MIP-sensor permits fast (30 min) analysis, is cheap, easy to prepare and has the potential to be integrated with portable devices. Due to its simplicity and efficiency, surface imprinting by electropolymerization was used to prepare a MIP on a screen-printed carbon electrode (SPCE). MIP preparation was achieved by cyclic voltammetry (CV), using dopamine (DA) as a monomer in the presence of DCF. The differential pulse voltammetry (DPV) detection of DCF at MIP/SPCE and non-imprinted control sensors (NIP) showed an imprinting factor of 2.5. Several experimental preparation parameters were studied and optimized. CV and electrochemical impedance spectroscopy (EIS) experiments were performed to evaluate the electrode surface modifications. The MIP sensor showed adequate selectivity (in comparison with other drug molecules), intra-day repeatability of 7.5%, inter-day repeatability of 11.5%, a linear range between 0.1 and 10 μM (r2 = 0.9963) and a limit of detection (LOD) and quantification (LOQ) of 70 and 200 nM, respectively. Its applicability was successfully demonstrated by the determination of DCF in spiked water samples (river and tap water).

scholarly journals An Electrochemical Sensor Based On Graphite Electrode Modified With Silica Containing 1-N-Propyl-3-Methylimidazolium Species For Determination Of Ascorbic Acid

2019 ◽  
Vol Vol. 14, No.1 ◽  
pp. 5-14 ◽  
Author(s):  
Anastasiya Tkachenko ◽  
Mykyta Onizhuk ◽  
Oleg Tkachenko ◽  
Leliz T. Arenas ◽  
Edilson V. Benvenutt ◽  
...  
Keyword(s):  
Ascorbic Acid ◽  
Cyclic Voltammetry ◽  
Electrochemical Sensor ◽  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Pharmaceutical Formulations ◽  
Differential Pulse ◽  
Long Term Stability ◽  
Diffusion Limited

In the present study, an electrochemical sensor based on the electrode (SiMImCl/C) consisting of graphite and silica, grafted with 1-n-propyl-3-methylimidazolium chloride was used for ascorbic acid (AA) quantification in pharmaceuticals and food formulations. Cyclic voltammetry and electrochemical impedance spectroscopy were applied for electrochemical characterization of the SiMImCl/C electrode. The cyclic voltammetry study revealed that the oxidation of AA on this electrode is an irreversible process, realized by adsorption and diffusion limited step. The differential pulse voltammetry was applied to develop a procedure for the AA determination. The linear range was found to be 0.3–170 μmol L-1 and the limit of detection – 0.1 μmol L-1. The proposed SiMImCl/C electrode has long term stability and does not show electrochemical activity towards the analytes, which commonly coexist with AA. The sensor was successfully used for quantification of AA in food and pharmaceutical formulations.

Electrochemical Detection of Fenthion Insecticide in Olive Oils by a Sensitive Non-Enzymatic Biomimetic Sensor Enhanced with Metal Nanoparticles

2021 ◽  
Vol 5 (1) ◽  
pp. 64
Author(s):  
Youssra Aghoutane ◽  
Nezha El Bari ◽  
Zoubida Laghrari ◽  
Benachir Bouchikhi
Keyword(s):  
Electrochemical Impedance ◽  
Differential Pulse ◽  
Organophosphate Insecticide ◽  
Imprinted Polymer ◽  
High Recovery ◽  
Molecularly Imprinted ◽  
Olive Oils ◽  
Pulse Voltammetry ◽  
Biomimetic Sensor

Fenthion, an organophosphate insecticide, is a cholinesterase inhibitor and is highly toxic. An electrochemical sensor based on molecularly imprinted polymer is developed here for its detection. For this purpose, 2-aminothiophenol mixed with gold nanoparticles was immobilized on screen-printed gold electrodes. The FEN pattern was then fixed before being covered with 2-aminothiophenol. Cyclic voltammetry, differential pulse voltammetry and electrochemical impedance spectroscopy methods were used for the electrochemical characterization. The low detection limit was 0.05 mg/Kg over a range of 0.01–17.3 µg/mL. The sensor was successfully applied for the determination of FEN in olive oil samples with high recovery values.

Encapsulation of hemin in Fe-based metal-organic frameworks and its application for the direct determination of aflatoxin M1

2021 ◽  
pp. 1-10
Author(s):  
F. Jahangiri-Dehaghani ◽  
H.R. Zare ◽  
Z. Shekari
Keyword(s):  
Electrochemical Impedance ◽  
Metal Organic Frameworks ◽  
Direct Determination ◽  
Differential Pulse ◽  
Aflatoxin M1 ◽  
Label Free ◽  
Electrochemical Aptasensor ◽  
Selective Determination ◽  
Metal Organic

A label-free electrochemical aptasensor was constructed for the sensitive and selective determination of AFM1. For preparation of the aptasensor, the AFM1 aptamer was immobilised on the surface of a glassy carbon electrode modified with hemin encapsulated in Fe-based metal-organic frameworks (hemin@Fe-MIL-101). The morphology and the structure of Fe-MIL-101 and hemin@Fe-MIL-101 were evaluated by scanning electron microscopy, Fourier-transform infrared spectroscopy, X-ray powder diffraction and Brunauer-Emmett-Teller-N2 sorption methods. Electrochemical impedance spectroscopy and cyclic voltammetry were performed to monitor the fabrication process of the electrochemical aptasensor. The electrochemical reduction current of hemin encapsulated in Fe-MIL-101 serves as a signal for the quantitative determination of AFM1. Differential pulse voltammetry was done to determine the AFM1 concentration in the linear range of 1.0×10-1-100.0 ng/ml. The detection limit of AFM1 was estimated to be 4.6×10-2 ng/ml. Finally, the fabricated aptasensor was applied to determine AFM1 in raw and boiled milk samples.

scholarly journals Selective Determination of Dopamine in Presence of Ascorbic Acid Using Nafion Coated Methylene Blue Functionalized Graphite Electrode

2019 ◽  
Vol 31 (10) ◽  
pp. 2185-2190
Author(s):  
G. Sivasankari ◽  
K. Sivasankari ◽  
T. Nalini ◽  
P. Padmapriya ◽  
M. Nadhiya
Keyword(s):  
Methylene Blue ◽  
Ascorbic Acid ◽  
Modified Electrode ◽  
Electrode Surface ◽  
Graphite Electrode ◽  
Low Cost ◽  
Differential Pulse ◽  
Selective Determination ◽  
The Stability

An electrochemical sensor has been developed using methylene blue (MB) unctionalized graphite for the selective determination of dopamine in the presence of ascorbic acid. The immobilization of methylene blue on graphite was done by carbodiimide coupling method. The methylene blue functionalized graphite was characterized by SEM, FTIR spectroscopy and UV-visible spectroscopy. The immobilization of methylene blue functionalized graphite (MB-G) on the electrode surface was made by drop casting a small volume of MB-G dispersed methanol solution on the electrode surface. About 5 L of 0.5 % Nafion solution was also dropcasted for the stability and selectivity. The MB-G modified electrode was characterized by cyclic voltammetry. The modified electrode promotes the electrocatalytic oxidation of dopamine at a lower potential of 160 mV. The selective determination of dopamine in the presence of 100 times higher concentration of ascorbic acid was achieved by differential pulse voltammetry. The modified electrode offered a simple, selective and sensitive determination of low levels of dopamine. Also the oxidation over potential was reduced to an extent of 360 mV comparing with the bare graphite electrode. The proposed sensor has the advantage of easy fabrication, low cost, good sensitivity, reproducibility and stability.

scholarly journals Determination of Methyldopa and Paracetamol in Pharmaceutical Samples by a Low Cost Genipa americana L. Polyphenol Oxidase Based Biosensor

2019 ◽  
Vol 9 (3) ◽  
pp. 416-422
Author(s):  
Rafael Souza Antunes ◽  
Douglas Vieira Thomaz ◽  
Luane Ferreira Garcia ◽  
Eric de Souza Gil ◽  
Vernon Sydwill Sommerset ◽  
...  
Keyword(s):  
Electrochemical Impedance ◽  
Low Cost ◽  
Differential Pulse ◽  
Pharmaceutical Samples ◽  
Polyphenol Oxidases ◽  
Voltammetric Techniques ◽  
Relative Standard ◽  
Pulse Voltammetry ◽  
Phenolic Drugs

Purpose: Jenipapo fruit (Genipa americana L) is a natural source of polyphenol oxidases (PPOs) whose potential in pharmaceutical analysis is noteworthy. Henceforth, this work reports the electrochemical study of a low-cost PPO-based biosensor produced from the crude extract of Jenipapo fruits and accounts a practical approach to employ this biosensor in the determination of methyldopa and paracetamol in pharmaceutical samples. Methods: In order to investigate the electrochemical properties of the biosensor, theoretical and practical approaches were employed, and both samples and the biosensor were analyzed through electrochemical impedance spectroscopy (EIS) and voltammetric techniques, namely: differential pulse voltammetry (DPV) and cyclic voltammetry (CV). Results: showcased that the biosensor presented good analytical features, as well as low detection limits (8 μmol L-1 for methyldopa and 5 μmol L-1 for paracetamol). The relative standard deviation was less than 5% mid-assay. Conclusion: The use of this biosensor is a reliable, low cost and useful alternative in the pharmaceutic determination of phenolic drugs (e.g. methyldopa and paracetamol).

scholarly journals Paracetamol Sensing with a Pencil Lead Electrode Modified with Carbon Nanotubes and Polyvinylpyrrolidone

Chemosensors ◽  
2020 ◽  
Vol 8 (4) ◽  
pp. 133
Author(s):  
Piyanut Pinyou ◽  
Vincent Blay ◽  
Kantapat Chansaenpak ◽  
Sireerat Lisnund
Keyword(s):  
Carbon Nanotubes ◽  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Low Cost ◽  
Electrical Contact ◽  
Pharmaceutical Preparations ◽  
Single Wall Carbon Nanotubes ◽  
Wave Voltammetry ◽  
Lead Electrode

The determination of paracetamol is a common need in pharmaceutical and environmental samples for which a low-cost, rapid, and accurate sensor would be highly desirable. We develop a novel pencil graphite lead electrode (PGE) modified with single-wall carbon nanotubes (SWCNTs) and polyvinylpyrrolidone (PVP) polymer (PVP/SWCNT/PGE) for the voltammetric quantification of paracetamol. The sensor shows remarkable analytical performance in the determination of paracetamol at neutral pH, with a limit of detection of 0.38 μM and a linear response from 1 to 500 μM using square-wave voltammetry (SWV), which are well suited to the analysis of pharmaceutical preparations. The introduction of the polymer PVP can cause dramatic changes in the sensing performance of the electrode, depending on its specific architecture. These effects were investigated using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM). The results indicate that the co-localization and dispersion of PVP throughout the carbon nanotubes on the electrode are key to its superior electrochemical performance, facilitating the electrical contact between the nanotubes and with the electrode surface. The application of this sensor to commercial syrup and tablet preparations is demonstrated with excellent results.

scholarly journals Development of membrane electrodes for selective determination of lisinopril in pharmaceuticals

2019 ◽  
Vol 10 (1) ◽  
Author(s):  
Nagaraju Rajendraprasad ◽  
Kanakapura Basavaiah
Keyword(s):  
Enzyme Inhibitor ◽  
Limit Of Detection ◽  
Low Cost ◽  
Ion Pairs ◽  
Standard Addition ◽  
Phosphomolybdic Acid ◽  
Selective Determination ◽  
Accuracy And Precision ◽  
Selective Membrane

Abstract Background Lisinopril (LNP) is an angiotensin-converting enzyme inhibitor used as anti-hypertensive, cardiovascular, in anti-prophylactic and anti-diabetic nephropathy drug. Development of two new, simple, low cost, and selective membrane-based ion-selective electrodes has been proposed for the determination of LNP in pharmaceuticals. Methods The electrodes are based on poly(vinyl)chloride membrane doped with LNP-phosphotungstic acid (LNP-PTA) and LNP-phosphomolybdic acid (LNP-PMA) ion-pairs as molecular recognition materials. Results The developed LNP-PTA and LNP-PMA electrodes are applicable for the determination of LNP over the linear range of 5 × 10−5–2.4 × 10−3 mol l−1. The working pH ranges to measure potentials were 2.5 to 6.4 and 2.3 to 6.0 for LNP-PTA and LNP-PMA ISEs, respectively. The electrodes displayed the rapid Nernstian responses as revealed by the values of slopes 55.06 and 52.39 mV/decade, with limit of detection (LOD) values of 1.2 × 10−5 and 1.18 × 10−5 mol l−1 for LNP-PTA and LNP-PMA electrodes, respectively. The limits of quantitation (LOQ) values have also been calculated for both the electrodes. The developed electrodes have potential stability for up to 1 month and emerged as highly selective for the determination of LNP over other spiked ions and compounds. Conclusions The proposed electrodes have been validated and found that they are suitable for the determination of LNP in pharmaceuticals in pure form and in dosage forms. The results obtained in the analysis of LNP using proposed electrodes have been compared statistically with reference method’s results to assess the accuracy and precision. Robustness and ruggedness of the developed electrodes have also been checked and found satisfactory. The recovery studies have been performed by standard addition procedure to assess the role of excipients in tablets containing LNP and the results obtained are satisfactory.

Indirect Differential Pulse Voltammetric Determination of Fluoride Ions at Carbon Paste Electrode Modified with Porous and Electroactive Fe3+/Fe2+ Based-Metal Organic Frameworks Type MIL-101(Fe)

2021 ◽  
Author(s):  
Ashraf Mahmoud ◽  
Mater Mahnashi ◽  
Samer Abu-Alrub ◽  
Saad Kahatani ◽  
Mohamed El-Wekil
Keyword(s):  
Carbon Paste Electrode ◽  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Metal Organic Frameworks ◽  
Differential Pulse ◽  
Carbon Paste ◽  
X Ray ◽  
Metal Organic ◽  
Paste Electrode

Abstract An innovative and reliable electrochemical sensor was proposed for simple, sensitive and selective determination of F- ions. The sensor is based on the fabrication of porous and electroactive Fe-based metal organic frameworks [MIL-101(Fe)]. It was blended with graphite powder and liquid paraffin oil to from carbon paste electrode (CPE). The MIL-101(Fe)@CPE was characterized using different techniques such as scanning electron microscope, powder X-ray diffraction spectroscopy, Fourier transform infrared spectroscopy, energy dispersive X-ray, cyclic voltammetry, electrochemical impedance spectroscopy, differential pulse voltammetry. The MIL-101(Fe)@CPE exhibited two redox peaks (anodic and cathodic) corresponding to Fe3+ and Fe2+, respectively. The determination of F- ions based on the formation of a stable fluoroferric complex with Fe3+/ Fe2+, decreasing the currents of redox species. It was found that the anodic peak current (Ipa) is linearly proportional to the concentration of F- in the range of 0.67-130 µM with a limit of detection (S/N=3) of 0.201 µM. The electrode exhibited good selectivity towards F- detection with no significant interferences from common anions. The as-fabricated sensor was applied for the determination of F- in environmental water samples with recoveries % and RSDs % in the range of 98.1-102.4 % and 2.4-3.7 %, respectively.

scholarly journals Electrochemical Sensor Based on Molecularly Imprinted Polymer for the Detection of Cefalexin

Biosensors ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 31 ◽  
Author(s):  
Bogdan Feier ◽  
Adrian Blidar ◽  
Alexandra Pusta ◽  
Paula Carciuc ◽  
Cecilia Cristea
Keyword(s):  
Electrochemical Sensor ◽  
Molecularly Imprinted Polymer ◽  
Electrochemical Impedance ◽  
Limit Of Detection ◽  
Imprinted Polymer ◽  
Boron Doped Diamond ◽  
Molecularly Imprinted ◽  
Diamond Electrode ◽  
The Difference ◽  
Mip Sensor

In this study, a new electrochemical sensor was developed for the detection of cefalexin (CFX), based on the use of a molecularly imprinted polymer (MIP) obtained by electro‒polymerization in an aqueous medium of indole-3-acetic acid (I3AA) on a glassy carbon electrode (GCE) and on boron-doped diamond electrode (BDDE). The two different electrodes were used in order to assess how their structural differences and the difference in the potential applied during electrogeneration of the MIP translate to the performances of the MIP sensor. The quantification of CFX was performed by using the electrochemical signal of a redox probe before and after the rebinding of the template. The modified electrode was characterized using atomic force microscopy (AFM), scanning electron microscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The influence of different parameters on the fabrication of the sensor was tested, and the optimized method presented high selectivity and sensitivity. The MIP-based electrode presented a linear response for CFX concentration range of 10 to 1000 nM, and a limit of detection of 3.2 nM and 4.9 nM was obtained for the BDDE and the GCE, respectively. The activity of the sensor was successfully tested in the presence of some other cephalosporins and of other pharmaceutical compounds. The developed method was successfully applied to the detection of cefalexin from real environmental and pharmaceutical samples.

scholarly journals Carbon nanotube-ionic liquid nanocomposite modified carbon-ceramic electrode for determination of dopamine in real samples

2013 ◽  
Vol 11 (7) ◽  
pp. 1172-1186 ◽  
Author(s):  
Mir Majidi ◽  
Reza Baj ◽  
Abdolhossein Naseri
Keyword(s):  
Ionic Liquid ◽  
Carbon Nanotube ◽  
Modified Electrode ◽  
Electrochemical Impedance ◽  
Differential Pulse ◽  
Selective Determination ◽  
Carbon Ceramic Electrode ◽  
Electro Oxidation ◽  
Carbon Ceramic

AbstractRoom temperature 1-butyl-3-methylimidazolium tetraflouroborate ([BMIM][BF4]) ionic liquid was employed for dispersion of multi walled carbon nanotubes (MWCNTs) and the formation of nanocomposite on the surface of a carbon-ceramic electrode. The surface of the modified electrode was characterized using scanning electron microscopy and electrochemical impedance spectroscopy. The modified electrode exhibited excellent electrochemical activity to oxidation of dopamine (DA); whereas electro oxidation of ascorbic acid (AA) was not seen and electro oxidation of uric acid (UA) appeared at a more positive potential than DA. The multi walled carbon nanotube-ionic liquid nanocomposite modified carbon-ceramic electrode was used for the selective determination of DA in the presence of high levels of AA and UA using differential pulse voltammetry. The calibration curve for DA was linear in the range of 3.00 to 130 µM with the detection limit (S/N=3) of 0.87 µM. The present electrode was successfully applied to the determination of DA in some commercial pharmaceutical samples and human blood serum.

Sign in / Sign up

Export Citation Format

Share Document