scholarly journals Hysteretic Response of Tilt-Up Concrete Precast Walls with Embedded Steel Plate Connections

2020 ◽  
Vol 12 (19) ◽  
pp. 7907
Author(s):  
Hyun-Do Yun ◽  
Hye-Ran Kim ◽  
Won-Chang Choi
Keyword(s):  
Prestressed Concrete ◽  
Structural Integrity ◽  
Precast Concrete ◽  
American Concrete Institute ◽  
Steel Plates ◽  
Test Results ◽  
Wall Panel ◽  
Concrete Wall ◽  
Concrete Panels ◽  
Wall Panels

Many connection systems are available that can transfer tension and shear loads from a precast concrete wall panel to a floor slab. However, due to the insufficient anchor depth in relatively thin precast concrete panels, it is difficult to attain adequate ductility and stiffness to ensure structural integrity. Based on the authors’ previous research results, the supplementary reinforcement of embedded steel plates in precast concrete wall panels can enhance stiffness while maintaining allowable displacement and ductility. In this study, three full-size tilt-up precast concrete panels with embedded steel plates were fabricated. Lateral cyclic loads were applied to full support structures consisting of a precast concrete wall panel and a foundation. The test results were compared with the results predicted using existing code equations found in the American Concrete Institute 318-14 and the Prestressed Concrete Institute Handbooks. The test results confirm that the supplementary reinforcement of thin precast concrete wall panels can provide (i) the required strength based on current code equations, (ii) sufficient ductility, and (iii) the energy dissipation capacity to resist cyclic loading.

INFLUENCE OF RECTANGULAR STEEL SPLICE-SLEEVE FOR PRECAST CONCRETE CONNECTION

2015 ◽  
Vol 77 (12) ◽  
Author(s):  
Ahmad Baharuddin Abd Rahman ◽  
Tan Kee Hong ◽  
Izni Syahrizal Ibrahim ◽  
Roslli Noor Mohamed
Keyword(s):  
Structural Integrity ◽  
Precast Concrete ◽  
Tensile Load ◽  
Steel Plates ◽  
Steel Bar ◽  
Tensile Performance ◽  
Bond Property ◽  
The Many ◽  
Steel Sleeve

Precast concrete building system has gained its popularity in Malaysia because of the many advantages such as high quality of structural components, less labour intensive at the construction site, and shorter completion time of a project. One of the constraints in precast concrete structures is to ensure that the connections are strong enough to ensure the structural integrity and robustness of the overall frames. In this study, a total of nine rectangular steel splice-sleeve connections were tested experimentally under incremental tensile loads. Two steel plates were inserted and welded to each end of the steel splice-sleeve. The steel plates act as shear key to provide the interlocking mechanism to the grout and to enhance the bond property between the grout and the splice. These plates were adopted to prevent the grout slippage from the sleeve. The grout strength, embedded steel bar lengths and the size of the steel sleeve splice were varied among the specimens to study their effect on the tensile performance of the connection. The results showed that the higher strength of grout, longer embedded length of steel bar and smaller size of the sleeve contributes to a higher ultimate tensile load.

Insulation Type Effect on the Direct Shear Behavior of Concrete Sandwich Panel (CSP) with Non-Shear Connectors

2013 ◽  
Vol 663 ◽  
pp. 154-158 ◽  
Author(s):  
Tae Sik Oh ◽  
Seok Joon Jang ◽  
Kang Min Lee ◽  
Hyun Do Yun
Keyword(s):  
Reinforced Concrete ◽  
Sandwich Panel ◽  
Residential Buildings ◽  
Precast Concrete ◽  
Test Results ◽  
Concrete Wall ◽  
Concrete Walls ◽  
Shear Connectors ◽  
Reinforced Concrete Walls ◽  
Pull Out

Precast concrete sandwich panels (PCSP) are often used as exterior cladding of residential buildings due to thermal efficiency. PCSP systems consist of two precast reinforced concrete walls separated by a layer of insulation and connected with connectors which penetrate the insulation layer and are anchored at two precast walls. This paper provides the pull-out test results of concrete sandwich panel (CSP) with non-shear connectors. The variables in this study were the casting direction of reinforced concrete walls and types of insulation. Test results indicated that the types of insulations and casting direction have a significant effect on the bond strength between concrete wall and insulation. The effect of insulation type is notable for CSP cast horizontally concrete walls.

Experimental Study on Local Compression of Concrete-filled Glass Fiber Reinforced Gypsum Wall Panel

2013 ◽  
Vol 671-674 ◽  
pp. 668-673
Author(s):  
Kao Zhong Zhao ◽  
Jian Feng Li ◽  
Feng Wang
Keyword(s):  
Glass Fiber ◽  
Test Results ◽  
Fiber Reinforced ◽  
Wall Panel ◽  
Gypsum Board ◽  
Local Pressure ◽  
Concrete Core ◽  
Glass Fiber Reinforced ◽  
Wall Panels ◽  
Capacity Calculation

The concrete-filled glass fiber reinforced gypsum wall panel is a kind of panel that the inside cavums of the glass fiber hollow gypsum panel is filled with concrete. The experimental results indicate that the concrete-filled glass fiber reinforced gypsum wall panel which has a better performance of the force and can be used to be the bearing wall of a building can form a novel structural system. When the beams supporting the wall panels, the wall panels which under the beams is in local state of compression. It were gained that when the wall panels are in the local compression state , local pressure loads are primarily borne by the concrete core columns and fiber gypsum board will damage in advance through the eighteen experimental wall panel specimens which in local compression. The test results show that the final destruction of the concrete is caused by being crushed and the contribution of the gypsum wall panel to local compression bearing is small. Compressive stress can only spread in the local loading on concrete core columns, cannot be expanded into an adjacent stud. Finally, the local compression bearing capacity calculation formula of the concrete-filled glass fiber reinforced gypsum wall panel is obtained by analysis of the test results.

scholarly journals Steel Beam-Column Joint with Discontinuous Vertical Reinforcing Bars

2015 ◽  
pp. 197-204
Author(s):  
Ju-Yun Hu ◽  
Won-Kee Hong ◽  
Seon-Chee Park ◽  
Jisoon Kim
Keyword(s):  
Load Transfer ◽  
Precast Concrete ◽  
Steel Plates ◽  
Steel Beam ◽  
Test Results ◽  
Reinforcing Bars ◽  
Concrete Frames ◽  
Steel Members ◽  
Column Joint ◽  
In Parenthesis

The authors proposed steel beam-column connections for precast concrete frames in previous studies. The steel-concrete composite frames provided fast assembly time as steels with economy of concrete structures. However, when enough space is not available at column-beam joints steel sections from beams cannot be connected with column brackets. This paper suggests that some vertical reinforcing bars are disconnected at joints by connecting vertical steel reinforcements to steel plates placed above and below column steels to provide load transferring path. Loads from re-bars are transferred to steel plates, column steels and back to steel plates and re-bars below column steels. Re-bars connected to steel plates by bolts at above and below column steel are discontinued at joint to provide spaces for connections between column brackets and beam steels. Extensive experiments were performed to verify load transfer from re-bars to steel plates above joints and steel plates to re-bars below joint. The flexural load bearing capacity of a column with total of 24 vertical re-bars were compared to columns with discontinuous re-bars at joints. The number of discontinuous re-bars at joint used in column specimen was 0 (0.0%), 4 (16.7%), 12 (50.0%), and 20 (83.3%). The numbers in parenthesis are the percentages of discontinuous rebars to the total number of vertical re-bars of control column. Experiments showed how loads from vertical steel reinforcements that were cut off at joints were transferred to steel plate. The test results also demonstrated that a part of flexural capacities were reduced for specimen with discontinuous vertical re-bars. The reduction of 6.0 %, 13.7% and 54.0% of flexural capacities were observed for columns with 4 (16.7%), 12 (50.0%) and 20 (83.3%) discontinuous vertical rebars, respectively. The test results can be used to design vertical reinforcing bars and column joints that can provide space for column brackets to which steel members of beams are connected.

Sign in / Sign up

Export Citation Format

Share Document