scholarly journals Effect of Sweep Angle and a Half Sine Wave on Roll Damping Derivative of a Delta Wing

2019 ◽  
Vol 8 (2S3) ◽  
pp. 984-989
Keyword(s):  
Hypersonic Flow ◽  
Initial Conditions ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Sine Wave ◽  
Roll Damping ◽  
Sweep Angle ◽  
Strip Theory ◽  
Wide Range

This paper presents the effect of sweep angle on a roll of damping derivative of a delta wing with half sine wave for an attached shock case in supersonic/hypersonic flow has been studied analytically. The Ghosh Strip theory is replicated. By combining this with the similitude at high-speed flows lead to giving a piston theory. The initial conditions for the applicability of the theory are that the attached wave must be attached with the leading edge of the wing. The results of the present study reveals that with the increments in the sweep angles; it results in continuous decrease in the roll damping derivative, it is also seen that the magnitude of the decrement for lower sweep angle is considerable as compared to the higher values of the sweep angles due to the drastic change in the surface area of the wing. Roll damping derivative progressively increases with the angle of attack; however, with the increase in the inertia level of the flow, it results in the decrement in the damping derivative and later conforms to the Mach number independence principle. Effect of the leading edge bluntness and viscous effects are neglected. Results have been obtained for the supersonic/hypersonic flow of perfect gases over a wide range of angle of attack, planform area for different Mach numbers. In the present study, attention is on the effect of sweep angle of the wing on roll damping derivative at a different angle of attack and inertia level has been studied. In the contemporary theory, Leeward surface is taken along with shock waves attached with the leading edge.

Optimization of Aerodynamic Parameters of Cropped Delta Wing with Fence at Sonic Mach Number

2019 ◽  
Vol 16 (2) ◽  
pp. 403-409
Author(s):  
M. P. Arun ◽  
M. Satheesh ◽  
Edwin Raja J. Dhas
Keyword(s):  
Shock Wave ◽  
Boundary Condition ◽  
Mach Number ◽  
Sound Speed ◽  
Delta Wing ◽  
Leading Edge ◽  
Supersonic Speed ◽  
Sweep Angle ◽  
Ansys Fluent ◽  
Aerodynamic Parameters

Manufacturing and maintaining different aircraft fleet leads to various purposes, which consumes more money as well as man power. Solution to this, nations that are leading in the field of aeronautics are performing much research and development works on new aircraft designs that could do the operations those were done by varied aircrafts. The foremost benefit of this delta wing is, along the huge rearward sweep angle, the wing’s leading edge would not contact the boundary of shock wave. Further, the boundary is produced at the fuselage nose due to the speed of aircraft approaches and also goes beyond the transonic to supersonic speed. Further, rearward sweep angle greatly worse the airspeed: wings under normal condition to leading edge, so permits the aircraft to fly at great transonic, subsonic, or supersonic speed, whereas the over wing speed is kept to minimal range than that of the sound speed. The cropped delta wing with fence has analysed in three cases: Fences at 3/4th distance from the centre, with fences at half distance from the centre and with fences at the centre. Further, the delta wing that cropped is exported to ANSYS FLUENT V14.0 software and analysed by making the boundary condition settings like sonic Mach number of flow over wing along with the angle of attack.

scholarly journals Experiment on Wingtip Vortices using a Half Deltawing at the Tips

2019 ◽  
Vol 8 (2S8) ◽  
pp. 1633-1638
Keyword(s):  
Delta Wing ◽  
Tangential Velocity ◽  
Leading Edge ◽  
Force Balance ◽  
Aviation Industry ◽  
Sweep Angle ◽  
Wingtip Vortex ◽  
Image Velocimetry ◽  
Rotating Wing ◽  
Naca 0015

The counter rotating wing tip vortices produced by the aircraft continues to be a big concern for the aviation industry and the aircraft manufacturers due to its hazardous effects on the flight safety and aircraft efficiency. The strength of the vortices poses severe problems to the aircraft operations. Manufacturers developed various wingtip devices to alleviate this problem, but still it is not fully understood and solved. In this thesis, the effectiveness of using a half delta wing at the tips is investigated. The flow field over a low aspect ratio NACA 0015 wing fitted with a slender sharp half delta wing with a leading edge sweep angle 700 at a Reynolds number 1.87 ×105 is investigated. Particle image velocimetry is used to quantify the vortex structure and force balance measurements are used to calculate the aerodynamic data of the wing. The peak vorticity, peak tangential velocity are decreased due to the addition of half delta wing. The over-all radius of the wingtip vortex increased showing a diffused vortex due to the addition of the half delta wing. The core circulation is decreased leading to a lower strength vortex. Though the tip device increased the drag, it increases the aerodynamic efficiency through the improvement in L/D.

A Study of the Flow Field Associated with a Steadily-Rolling Slender Delta Wing

1964 ◽  
Vol 68 (638) ◽  
pp. 106-110 ◽  
Author(s):  
J. K. Harvey
Keyword(s):  
Flow Field ◽  
Static Pressure ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Rolling Moment ◽  
Air Stream ◽  
Total Head ◽  
Theoretical Predictions ◽  
Attached Flow

SummaryIn this paper an experiment is described in which a detailed study was made of the flow field associated with a slender sharp-edged delta wing which was rolling steadily at zero angle of attack to an air stream. The investigation was made by performing two pressure surveys: first , one of the static pressure acting on the wing’s surface and second by measuring the total-head distribution in the neighbourhood of the wing. From the former the local rolling-moment coefficients, Clp, are evaluated and these are compared with the predictions for attached flow, thus assessing the contributions to the forces acting on the wing which arise as a consequence of the leading-edge separations. The second set of surveys is used to construct a picture of the flow-field details and this is compared with that known to occur on a similar wing when it is set at an angle of attack to the airstream. One interesting finding is that the secondary separation which appears to cause the discrepancy between the theoretical predictions and the measurements made on slender wings at incidence, is absent in this configuration and thus it is concluded that these data could be used for a more meaningful test of the theory.

Experimental Control of Vortex Breakdown by Pulsed Blowing Over a Delta Wing With Rounded Leading-Edge

2002 ◽  
Author(s):  
Renac Florent ◽  
Molton Pascal ◽  
Barberis Didier
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Laser Sheet ◽  
Leading Edge ◽  
Control Device ◽  
Surface Flow ◽  
Sweep Angle ◽  
Laminar To Turbulent Transition ◽  
Pressure Distributions ◽  
Oil Flow

The purpose of this study is to construct and test an experimental device to control vortex on a delta wing. The model has a root chord of c = 690mm and a sweep angle of Λ = 60°. The control system is based on four rectangular slits 50 mm long and 0.2 mm wide running along the leading edge. This configuration produces jets normal to the leading edge. The mass flow rates and frequencies of injection can be varied independently. The results are shown in the form of surface flow visualizations, with the skin friction pattern exhibited by oil flow visualization, and the laminar-to-turbulent transition by acenaphthene. Mean and instantaneous surface pressure distributions were determined with Kulite™ sensors and the velocity field was determined by 3D laser Doppler velocimetry (LDV) measurements. Control device efficiencies were evaluated by laser sheet visualization.

Nonlinear lift increase at high angles of attack for double swept waverider

2020 ◽  
Vol 34 (14n16) ◽  
pp. 2040124
Author(s):  
Chuan-Zhen Liu ◽  
Peng Bai
Keyword(s):  
Shock Wave ◽  
Mach Number ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Lower Surface ◽  
Aerodynamic Performance ◽  
Sweep Angle ◽  
Vital Interest ◽  
High Angles Of Attack ◽  
Nonlinear Increase

The nonlinear increase of the lift of the double swept waverider at high angles of attack is of vital interest. The aerodynamic performance of the double swept waverider is calculated and compared with that of single swept waveriders. Results suggest that the lift nonlinearity of the double swept waverider is stronger than that of equal-planform-area single swept one, and the nonlinearity increases as Mach number increases. Some scholars have proposed the “vortex lift” to explain the nonlinear lift increase, but it is questionable as the main lift of the waverider comes from the lower surface rather than the upper surface. This paper proposes another explanation that the nonlinear lift increase is related to the attachment of shock wave, influenced by the leading-edge sweep angle. The shock wave is more inclined to attach under the lower surface with smaller swept than that of larger swept as angle of attack increases. When the shock wave attaches, the pressure increase via angle of attack is nonlinear, leading to the nonlinearity of lift increase.

On the Vortex Breakdown Phenomenon in High Angle of Attack Flows Over Delta Wing Geometries

2014 ◽  
Author(s):  
Eric D. Robertson ◽  
Varun Chitta ◽  
D. Keith Walters ◽  
Shanti Bhushan
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
High Angle ◽  
High Angle Of Attack ◽  
Eddy Simulation ◽  
Wing Model

Using computational methods, an investigation was performed on the physical mechanisms leading to vortex breakdown in high angle of attack flows over delta wing geometries. For this purpose, the Second International Vortex Flow Experiment (VFE-2) 65° sweep delta wing model was studied at a root chord Reynolds number (Recr) of 6 × 106 at various angles of attack. The open-source computational fluid dynamics (CFD) solver OpenFOAM was used in parallel with the commercial CFD solver ANSYS® FLUENT. For breadth, a variety of classic closure models were applied, including unsteady Reynolds-averaged Navier-Stokes (URANS) and detached eddy simulation (DES). Results for all cases are analyzed and flow features are identified and discussed. The results show the inception of a pair of leading edge vortices originating at the apex for all models used, and a region of steady vortical structures downstream in the URANS results. However, DES results show regions of massively separated helical flow which manifests after vortex breakdown. Analysis of turbulence quantities in the breakdown region gives further insight into the mechanisms leading to such phenomena.

Flow Regimes over Delta Wings at Supersonic and Hypersonic Speeds

1976 ◽  
Vol 27 (1) ◽  
pp. 1-14 ◽  
Author(s):  
L C Squire
Keyword(s):  
Shock Layer ◽  
Delta Wing ◽  
Leading Edge ◽  
Flow Regimes ◽  
Lower Surface ◽  
Delta Wings ◽  
Thin Shock Layer ◽  
Wide Range ◽  
Wing Sweep ◽  
Edge Separation

SummaryThis paper concerns the boundaries between flow regimes for sharp-edged delta wings in supersonic flow and the relation of some predictions of thin-shock-layer theory to these boundaries. In particular, it is shown that the theory predicts that the attachment lines on the lower surface of a thin delta wing at supersonic speeds suddenly jump from just inboard of the leading edges to the centre line in certain flight conditions. In general there is close agreement between the conditions for this jump and the flight conditions corresponding to the change-over from attached flow to the leading-edge separation on the upper surface. Since the movement of the attachment lines on the lower surface must change the position of the sonic line and the nature of the expansion around the edge, it is suggested that the two phenomena are directly related. Thus thin-shock-layer theory can be used to establish the boundaries of the various flow regimes for a wide range of Mach number, incidence and wing sweep. The theory can also be used to predict the effects of wing thickness on leading-edge separation, but here the experimental data is very sparse and somewhat contradictory, so the value of the prediction in the case of thickness requires further investigation.

Lift Force of Delta Wings

1990 ◽  
Vol 43 (9) ◽  
pp. 209-221 ◽  
Author(s):  
Mario Lee ◽  
Chih-Ming Ho
Keyword(s):  
Lift Force ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Surface Flux ◽  
Experimental Results ◽  
Geometrical Parameters ◽  
Two Dimensional ◽  
Delta Wings ◽  
Vorticity Balance

On a delta wing, the separation vorticies can be stationary due to the balance of the vorticity surface flux and the axial convection along the swept leading edge. These stationary vortices keep the wing from losing lift. A highly swept delta wing reaches the maximum lift at an angle of attack of about 40°, which is more than twice as high as that of a two-dimensional airfoil. In this paper, the experimental results of lift forces for delta wings are reviewed from the perspective of fundamental vorticity balance. The effects of different operational and geometrical parameters on the performance of delta wings are surveyed.

Sign in / Sign up

Export Citation Format

Share Document