Characterization of the Specificity in Three Commercial Dental Ceramic Powders

2017 ◽  
Vol 68 (4) ◽  
pp. 707-710
Author(s):  
Horia Manolea ◽  
Mirela Opri ◽  
Nicoleta Cioatera ◽  
Adriana Voinea ◽  
Radu Rica ◽  
...  
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Sintered Material ◽  
Xrd Analysis ◽  
Dental Ceramics ◽  
X Ray Diffraction ◽  
Ceramic Powders ◽  
X Ray ◽  
Scanning Electron

The aim of this study was to present and discuss the characteristics of three ceramic powders as well as the sintered material from the three commercial dental ceramics produced by Vita Zahnfabrik, Germany (VM13 and VMK Master, used for veneering metal frameworks, respectivelly VM9 used for veneering zirconia frameworks). An X-ray diffraction (XRD) analysis was performed, Raman spectra were recorded and the morphology of the samples was evidenced by using a high resolution scanning electron microscope, equipped with an EDXS detector. The results of this study corroborated with the presented literature data helps practitioners to better understand the interaction of these biomaterials with oral tissues, and, also helps researchers to modify the properties of ceramics for a better integration in the intraoral condition.

Synthesis and Characterization of Y2O3 Nanoflowers

2012 ◽  
Vol 465 ◽  
pp. 76-79 ◽  
Author(s):  
Shuang Zhan ◽  
Xia Li
Keyword(s):  
Fourier Transform ◽  
Phase Composition ◽  
Electron Microscope ◽  
Synthesis And Characterization ◽  
The Novel ◽  
X Ray Diffraction ◽  
Facile Hydrothermal Method ◽  
X Ray ◽  
Scanning Electron

The novel Y2O3 nanoflowers were synthesized through a facile hydrothermal method without using any catalyst or template. The phase composition and the microstructure of as-prepared products were characterized by field emission scanning electron microscope (FE-SEM), X-ray diffraction (XRD) as well as Fourier transform infrared spectrum. The formation mechanism for the Y2O3 flowers has been proposed.

Microstructural Characterization of Glass-to-Metal Brazed Joint

2012 ◽  
Vol 616-618 ◽  
pp. 1732-1735 ◽  
Author(s):  
Xi Hai Shen ◽  
Yu Gang Zheng ◽  
Liang Chang ◽  
Jin Jia Guo ◽  
Song Bin Ye ◽  
...  
Keyword(s):  
Thermal Power ◽  
Microstructural Characterization ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solar Thermal Power ◽  
Brazed Joints ◽  
Brazed Joint ◽  
Scanning Electron

Aiming at the glass-to-metal seals serving in the Solar Thermal Power (STP), glass-to-metal vacuum brazed joints were studied. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis were performed to examine the microstructure and element contents of interface seam on the glass-to-metal vacuum brazed joints. Also, the compositional concentration of the interface seam was measured by using energy dispersive spectroscopy (EDS).

scholarly journals X Preparation and Characterization of Carbon-Based Composite Nanofibers for Supercapacitor

2017 ◽  
Vol 17 (2) ◽  
pp. 129-134 ◽  
Author(s):  
Dawei Gao ◽  
Lili Wang ◽  
Chunxia Wang ◽  
Yuping Chang ◽  
Pibo Ma
Keyword(s):  
Carbon Nanotubes ◽  
Phase Composition ◽  
Electron Microscope ◽  
Surface Area ◽  
Composite Nanofibers ◽  
Carbon Composite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Abstract Polyacrylonitrile (PAN)/Co(OAc)2/carbon nanotubes (CNTs) composite nanofibers were fabricated via electrospinning with N,N-dimethylformamide (DMF) as solvent, and by carbonization and activation of the above precursor nanofibers, porous carbon composite nanofibers were successfully obtained. Scanning electron microscope, X-ray diffraction, ASAP 2020, and Solartron 1470 were used to characterize the surface morphology, the phase composition, specific surface area, and electrochemical property of the nanofibers, respectively. The result showed that some of the fibers were broken after sintering, and the surface area and pore volume of the porous C/Cu/CNTs were 771 m2/g and 0.347 cm3/g, respectively. The specific capacitance of the composite nanofibers reached up to 210 F/g at the current density of 1.0 A/g. Its energy density and power density were 3.1 Wh/Kg and 2,337 W/Kg, respectively, at the current of 0.5 and 5 mA.

Microstructural Characterization of a Fe-Based Compostie Reinforced by TiC

2011 ◽  
Vol 675-677 ◽  
pp. 835-838
Author(s):  
Jing Wang ◽  
Si Jing Fu ◽  
Hong Cheng
Keyword(s):  
Electron Microscope ◽  
Microstructural Characterization ◽  
Interfacial Structure ◽  
Synthesis Reaction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Tic Particle ◽  
Scanning Electron

The present work reported the preparation of TiC/Fe-based composite by the synthesis reaction from Ti, C and Fe. The sintered composites were characterized by X-ray diffraction, scanning electron microscope and transmission electron microscope. TiC, Fe3C and α-Fe were detected by X-ray diffraction analysis. The scanning and transmission electron micrographs revealed the morphology and distribution of the reinforcements, the microstructure of Fe matrix, the interfacial structure of TiC particle-to-Fe matrix. Moreover, the formation reason of the voids in composite was also discussed.

The Effect of CaCO3 Addition on Physical Properties of ZnO-Based Crystal Glaze

2012 ◽  
Vol 620 ◽  
pp. 12-16 ◽  
Author(s):  
Abdul Rashid Jamaludin ◽  
Shah Rizal Kasim ◽  
Zainal Arifin Ahmad
Keyword(s):  
Electron Microscope ◽  
Calcium Carbonate ◽  
Scanning Electron Microscope ◽  
Physical Properties ◽  
Crystallization Temperature ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

The effects of calcium carbonate (CaCO3) addition on the physical properties of ZnO-based crystal glaze batches were investigated. Samples were fired at different gloss firing temperatures ranging from 1180-1220°C with 3 hours soaking at 1060°C crystallization temperature. X-ray diffraction (XRD) analysis identifiedthe crystal phase occurred as willemite (Zn2SiO4) and the scanning electron microscope (SEM) analysis indicated that willemite crystals are in the acicular needle like shape that formed spherulite. The intensities of willemite peaks decreased with CaCO3 addition and completely vanished at 5.0 wt% CaCO3. Varied formation of spherulites developed of the surface of crystal glaze as the flows of the glaze stretched further as the amount of CaCO3 increased.

Fabrication and Characterization of a Feldspar-Alumina for Dental Ceramic

2010 ◽  
Vol 160-162 ◽  
pp. 424-427
Author(s):  
Guang Lei Zhang ◽  
Guo Qiang Qin ◽  
Yuan Hua Zhang ◽  
Pu Cheng ◽  
Chang Tao Shao
Keyword(s):  
Sinter Temperature ◽  
Bending Strength ◽  
Dental Ceramics ◽  
Alumina Ceramics ◽  
X Ray Diffraction ◽  
X Ray ◽  
Fabrication And Characterization ◽  
Sintering Method ◽  
Scanning Electron

Feldspar-alumina dental ceramics were produced by impressed sintering method and characterized by X-ray diffraction and scanning electron microscope techniques. The machinability of the obtained alumina ceramics was evaluated by grinding capacity in the simulative grinding experiment. The results show that an appropriate amount of feldspar additive can reduce the sinter temperature and improve density, bending strength and machinability of alumina dental ceramics. Under 10 wt% feldspar and 1450 °C sinter temperature, the relative density and bending strength of ceramic reached 93.62% and 235MPa, respectively.

scholarly journals Characterization of Fe Doped AC/TiO2

2019 ◽  
Vol 8 (12S) ◽  
pp. 1146-1147
Keyword(s):  
Activated Carbon ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Anatase Phase ◽  
Sol Gel ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Abstract: The photocatalytic composite Fe doped AC/TiO2 has been prepared by sol-gel method. The prepared Fe doped AC/TiO2 composite were characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD).The SEM analysis showed that Fe and TiO2 were attached to the Activated Carbon surfaces. The X-Ray Diffraction data showed that Fe doped AC/TiO2 composite mostly contained anatase phase.

scholarly journals Karakterisasi Membran ZSM-5 yang Disintensis dengan Variasi Jenis dan Ukuran Kasa Penyangga

2020 ◽  
Vol 16 (1) ◽  
pp. 1
Author(s):  
Ana Hidayati Mukaromah ◽  
Tulus Ariyadi ◽  
Inas Hasna Azizah ◽  
Mifbakhuddin Mifbakhuddin
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Energy Dispersive Spectroscopy ◽  
Energy Dispersive ◽  
X Ray Diffraction ◽  
X Ray ◽  
Aisi 316 ◽  
Scanning Electron

<p>Telah dilakukan sintesis dan karakterisasi membran ZSM-5 dengan penyangga kasa jenis 304 ukuran 200 dan 400 mesh dan jenis kasa AISI 316 ukuran 180 mesh. Tujuan penelitian ini adalah mensintesis membran ZSM-5 dengan penyangga kasa jenis 304 ukuran 200 dan 400 mesh dan jenis kasa AISI 316 ukuran 180 mesh dan mengkarakterisasi membran ZSM-5 hasil sintesis. Sintesis membran dilakukan dengan cara melapiskan prekursor ZSM-5 (<em>coating)</em> pada penyangga kasa yang telah diberi perlakuan dan dipanaskan pada suhu 90 °C selama 4 hari. Selanjutnya, membran yang dihasilkan dikarakterisasi engan metoda <em>X-ray diffraction</em> (XRD), <em>scanning electron microscope-energy dispersive spectroscopy</em> (SEM-EDS) dan <em>Fourier-transform infrared</em> (FTIR). Hasil citra SEM-EDS menunjukkan bahwa ukuran membran ZSM-5 yang semakin besar, menghasilkan jumlah lubang atau pori semakin banyak dengan luasan pori yang semakin kecil. Pola difraksi XRD menunjukkan bahwa membran yang dihasilkan mempunyai intensitas tertinggi pada 2 8º dan 23º yang merupakan karakteristik dari ZSM-5. Hasil spektra FTIR menunjukkan adanya serapan pada bilangan gelombang 450 cm<sup>-</sup><sup>1</sup>yang merupakan ciri khas membran ZSM-5.</p><p class="Text"><strong>Characterization of ZSM-5 Membranes Synthesized by Variation of Support Types and Sizes.</strong> Synthesis and characterization of ZSM-5 membrane were carried out with 304 type 200 and 400 mesh gauze supports and 180 mesh AISI 316 gauze types. The purpose of this study was to synthesize ZSM-5 membrane with 304 type 200 and 400 mesh gauze support and AISI 316 type 180 mesh size 180 mesh and characterize the synthesized ZSM-5 membrane. Membrane synthesis was carried out by coating the pre-treated gauze support with the ZSM-5 precursor and was heated at 90 °C for 4 days. Furthermore, the resulting membrane was characterized by X-ray diffraction (XRD), scanning electron microscope-energy dispersive spectroscopy (SEM-EDS) dan Fourier-transform infrared (FTIR). The SEM-EDX analysis shows that the increasing of ZSM-5 membrane size allowed pores number to increase with smaller pore surface area. The X-ray Diffraction pattern (XRD) shows that the resulting membrane has the highest intensity at 2  of 8º and 23º as the characteristics of ZSM-5. The FTIR spectra results show absorption at wavenumbers 450 cm<sup>-1</sup> which is a characteristic of ZSM-5 membranes.</p>

scholarly journals Penggunaan ZnO/zeolit sebagai katalis dalam degradasi tartrazin secara ozonolisis

2021 ◽  
Vol 12 (1) ◽  
pp. 53-64
Author(s):  
Zilfa Zilfa ◽  
Safni Safni ◽  
Febi Rahmi
Keyword(s):  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Electron Microscope ◽  
Natural Zeolite ◽  
Zeolite Catalyst ◽  
X Ray Diffraction ◽  
X Ray ◽  
Zeolite Structure ◽  
Scanning Electron

An investigation on modification of natural zeolite with ZnO for the degradation of tartrazine. In this study, ZnO as a semiconductor is modified into a natural zeolite as support to form ZnO/zeolite that can increase the efficiency degradation of tartrazine. Further, the formed catalyst was added to tartrazine by determining the variation in ozonolysis time, the amount of addition of the catalyst, and the addition of a catalyst time. The results of degradation were determined by UV-Vis spectrophotometer at 424 nm. The result showed that the percentage of degradation obtained on each catalyst in the degradation. The resulted percent degradation of 20 ml of tartrazine at concentration of 15 mg/L using 20 mg ZnO/zeolite was 56.80%, while using 0.77 mg ZnO was 42.25%, and with the addition of 19.23 mg of Zeolite was 31.18%, all of that condition was proceeded by 40 minutes of ozonolysis. Thus, the result indicates that the ZnO/zeolite catalyst can increase percentages of tartrazine degradation by ozonolysis. It is known that the catalyst ZnO/zeolite is very effective in increasing the degradation of tartrazine. Analysis of tartrazine compounds using fourier-transform infrared spectroscopy (FTIR) after degradation changes in wavenumber indicates that there is a breaking of the bonds of tartrazine compounds. Characterization of ZnO/zeolite catalyst using FTIR, X-Ray diffraction (XRD) and scanning electron microscope (SEM), in each spectrum there was no shift, indicating that there is no change in ZnO/zeolite structure

scholarly journals Undoped and Eu3+ Doped Magnesium-Aluminium Layered Double Hydroxides: Peculiarities of Intercalation of Organic Anions and Investigation of Luminescence Properties

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 736 ◽  
Author(s):  
Aurelija Smalenskaite ◽  
Lina Pavasaryte ◽  
Thomas Yang ◽  
Aivaras Kareiva
Keyword(s):  
Layered Double Hydroxides ◽  
Organic Anion ◽  
Sol Gel ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Organic Guests ◽  
Double Hydroxides ◽  
Scanning Electron

The Mg3/Al and Mg3/Al0.99Eu0.01 layered double hydroxides (LDHs) were fabricated using a sol-gel chemistry approach and intercalated with different anions through ion exchange procedure. The influence of the origin of organic anion (oxalate, laurate, malonate, succinate, tartrate, benzoate, 1,3,5-benzentricarboxylate (BTC), 4-methylbenzoate (MB), 4-dimethylaminobenzoate (DMB) and 4-biphenylacetonate (BPhAc)) on the evolution of the chemical composition of the inorganic-organic LDHs system has been investigated. The obtained results indicated that the type and arrangement of organic guests between layers of the LDHs influence Eu3+ luminescence in the synthesized different hybrid inorganic–organic matrixes. For the characterization of synthesis products X-ray diffraction (XRD) analysis, infrared (FTIR) spectroscopy, fluorescence spectroscopy (FLS), and scanning electron microscopy (SEM), were used.

Sign in / Sign up

Export Citation Format

Share Document