Weldability Studies of AISI 409 Ferritic Stainless Steel Thick Plates Using Electron Beam Welding Process

2021 ◽  
Vol 11 (2) ◽  
pp. 55-67
Author(s):  
Akash Doomra ◽  
Beant Singh ◽  
Sandeep Singh Sandhu
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Toughness ◽  
Base Metal ◽  
Electron Beam Welding ◽  
Weld Zone ◽  
Welding Process ◽  
Post Weld Heat Treatment ◽  
Weld Heat

In the present research, attempts have been made to weld 18 mm thick AISI 409 ferritic steel plate in a single pass with electron beam welding process. The welded joint was investigated for macrostructure, microstructural, microhardness, impact toughness, and tensile strength. The coarse ferritic grains of base metal were converted into fine equiaxed and columnar grains in the weld zone. The microhardness results revealed that for fusion zone and heat affected zone had 28% and 41% higher microhardness than the base metal. Further, post weld heat treatment at 550ºC/75 minutes resulted in 5% rise in ultimate tensile strength, 10% rise in yield strength, and 31% rise in impact toughness as compared to as welded specimens. The fractography of impact and tensile specimens revealed brittle mode of fracture and changed to ductile mode after post weld heat treatment.

scholarly journals Effect of post weld heat treatment on metallurgical and mechanical properties of electron beam welded AISI 409 ferritic steel

10.30544/545 ◽  
2020 ◽  
Vol 26 (3) ◽  
pp. 279-292
Author(s):  
Akash Doomra ◽  
Sandeep Singh Sandhu ◽  
Beant Singh
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Stainless Steel ◽  
Electron Beam ◽  
Ferritic Stainless Steel ◽  
Electron Beam Welding ◽  
Weld Zone ◽  
Welding Process ◽  
Post Weld Heat Treatment ◽  
Weld Heat

The applicability of ferritic stainless steel is restricted due to its low weldability, and this can be attributed to the severe grain growth in the weld zone during the solidification of the weld pool and formation of fully ferritic structure. This study aims to investigate the weldability of 18 mm thick AISI 409 ferritic stainless steel plates using an electron beam welding process without the use of filler metal. The joints were investigated for metallography characterization (microstructure, macrostructure, and microhardness) and mechanical behavior (tensile strength and impact toughness) in as-welded condition and after post-weld heat treatment at 550 ºC for 75 minutes. The weld zone exhibited large columnar grains in the direction perpendicular to the weld centerline and got refined after post-weld heat treatment. The ultimate tensile strength, yield strength, and microhardness of the weld zone were found higher than the base metal. The impact toughness of weld zone was found to be reduced by 45%, but the post-weld heat treatment improved the toughness by 40%. Results revealed that the electron beam welding process could be successfully employed for welding of AISI 409 ferritic stainless steel, which will increase its application range that requires thicker section of welded plates. Post-weld heat treatment was found to be advantageous for improving the microstructure and mechanical properties.

Research on Microstructure and Properties of Base Metal and Weld of Electron Beam Welding 0.30C-Cr-W Steel

2015 ◽  
Vol 817 ◽  
pp. 238-245
Author(s):  
Lin Tao Li ◽  
Mao Sheng Yang ◽  
Yun Ren
Keyword(s):  
Heat Treatment ◽  
Electron Beam ◽  
Base Metal ◽  
High Performance ◽  
Electron Beam Welding ◽  
Theoretical Calculations ◽  
Welding Process ◽  
Post Weld Heat Treatment ◽  
Aviation Industry ◽  
Temperature Impact

Due to the difficulty of manufacturing complex small pieces ofthe new bearing steel0.30C-Cr-W with high-performance in the aviation industry, the electron beam welding process are usually used for preparing the complex parts.Thewelding performance of 0.30C-Cr-W steelwas calculated by theory and confirmedby actual experiments.The base metal was preheated,then welded and heattreated for weldments.The purpose of this work is to study the properties and the microstructure changes of base metal after heat treatment, weldments before heat treatment and weldments after heat treatment.The results show that the base metalafter heat treatment is sorbitic,weldzone of weldments after heat treatmentismartensite and austenite, theprecipitated M23C6 and M6C in latter (the weld zoneof weldmentsafter heat treatment) were more thanthe former (the base metalafter heat treatment), and the strengthof the latter is 23.4%lower than the former, theroom temperature impact absorbing energy and hardness of the latter increased 13.5% and 6.6%. It may be considered that0.30-C-Cr-W steel is not suitablefor welding by the theoretical calculations, but after reasonable preheat and post-weld heat treatment, the mechanical properties of the weld afterheat treatment can satisfy the requirements.

Effect of post weld heat treatment and welding parameters on mechanical and corrosion characteristics of friction stir welded aluminium alloy AA2014-T6

2019 ◽  
Vol 43 (2) ◽  
pp. 230-236
Author(s):  
Ashok S. Kannusamy ◽  
Ravindran Ramasamy
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Welding Process ◽  
Post Weld Heat Treatment ◽  
Welding Parameters ◽  
Friction Stir ◽  
Heat Treated ◽  
Ageing Period ◽  
Weld Heat

This paper addresses the effect of post weld heat treatment methods on the mechanical and corrosion characteristics of friction stir welded aluminum alloy AA2014-T6. Aluminum alloy AA2014 is mainly used in applications that demand high strength to weight ratios, such as aerospace, marine, and industrial applications. In this work, AA2014-T6 plates of 6 mm thick were butt welded using a tool with a square profile. Tensile strength, hardness, and corrosion characteristics were compared between the samples as welded and post weld heat treated. Welded samples that were heat treated for a shorter ageing period (8 h) showed improved tensile strength irrespective of welding process parameters, compared to as-welded samples. The samples heat treated for a longer ageing period (9 h) showed a decline in tensile strength for low tool rotation speed. Hardness increased in welded samples heat treated for 8 h. Welded samples heat treated for 9 h show high passivity in corrosion media.

Microstructure of Al-Li Alloy Electron Beam Welding Joint after Post-Weld Heat Treatment

2012 ◽  
Vol 217-219 ◽  
pp. 1921-1927 ◽  
Author(s):  
Shao Gang Wang ◽  
Kuang Yu ◽  
Chuan Xiao Luo ◽  
Li Xing
Keyword(s):  
Heat Treatment ◽  
Electron Beam ◽  
Grain Boundary ◽  
Electron Beam Welding ◽  
Grain Morphology ◽  
Post Weld Heat Treatment ◽  
Joint Fracture ◽  
Δ Phase ◽  
Strengthening Phases ◽  
Weld Heat

Heat treatment was carried out to the 1420 Al-Li alloy electron beam welding (EBW) joints after welding, and the microstructures of welded joints are analyzed systematically before and after post-weld heat treatment (PWHT). The observation of joint microstructure demonstrates that the grain morphology of weldment changes from equiaxed dendrites in as-welded (AW) condition into equiaxed grains after PWHT, and that the fine strengthening phases precipitate within the grain. The XRD analysis of phase constituent and TEM observation of weldment indicate that the main strengthening phases in 1420 Al-Li alloy weldment are spheroidal δ′(Al3Li), β′(Al3Zr) and rod-like T(Al2MgLi) after PWHT. Furthermore, the δ′ phase precipitate free zone (PFZ) is found along the grain boundary. The scanning observation of joint fracture shows that Al-Li alloy EBW joint presents the characteristic of transgranular ductile fracture in AW condition. After PWHT, the Al-Li alloy welded joint presents the pattern of intergranular fracture. The variation of fracture mode is related to dispersed precipitation of δ′ phase and the formation of PFZ at the grain boundary in weldment after heat treatment.

scholarly journals Influence of post weld heat treatment on tensile properties of cold metal transfer (CMT) arc welded AA6061-T6 aluminium alloy joints

2019 ◽  
Vol 28 (1) ◽  
pp. 135-145 ◽  
Author(s):  
Addanki Ramaswamy ◽  
Sudersanan Malarvizhi ◽  
Visvalingam Balasubramanian
Keyword(s):  
Heat Treatment ◽  
Tensile Properties ◽  
Gas Metal Arc Welding ◽  
Weight Ratio ◽  
Welding Process ◽  
Metal Transfer ◽  
Post Weld Heat Treatment ◽  
Cold Metal Transfer ◽  
Cold Metal ◽  
Weld Heat

AbstractAluminium alloys of 6xxx series are widely used in the fabrication of light weight structures especially, where high strength to weight ratio and excellent weld-ability characteristics are desirable. Gas metal arc welding (GMAW) is the most predominantly used welding process in many industries due to the ease of automation. In this investigation, an attempt has been made to identify the best variant of GMAW process to overcome the problems like alloy segregation, precipitate dissolution and heat affected zone (HAZ) softening. Thin sheets of AA6061-T6 alloy were welded by cold metal transfer (CMT) and Pulsed CMT (PCMT). Among the two joints, the joint made by PCMT technique exhibited superior tensile properties due to the mechanical stirring action in the weld pool caused by forward and rearward movement of the wire along with the controllable diffusion rate at the interface caused by shorter solidification time. However, softening still exists in the welded joints. Further to increase the joint efficiency and to minimize HAZ softening, the joints were subjected to post weld heat treatment (PWHT). Approximately 10% improvement in the tensile properties had been observed in the PWHT joints due to the nucleation of strengthening precipitates in the weld metal and HAZ.

Study on Electron Beam Welding of AZ61 Magnesium Alloy

2010 ◽  
Vol 34-35 ◽  
pp. 1516-1520
Author(s):  
Hong Ye ◽  
Han Li Yang ◽  
Zhong Lin Yan
Keyword(s):  
Electron Beam ◽  
Magnesium Alloys ◽  
Welding Speed ◽  
Electron Beam Welding ◽  
Weld Zone ◽  
Welding Process ◽  
Processing Parameters ◽  
Beam Current ◽  
Fine Grained ◽  
Section Shape

Electron beam welding process of AZ61 with 10mm thickness magnesium alloys was investigated. The influence of processing parameters including focusing current, welding beam current and welding speed was researched. The results show that an ideal weld bead can be formed by choosing processing parameters properly. Focusing current is main parameter that determines cross section shape. The beam current and welding speed are main parameters that determine the weld width and dimensions. The test results for typical welds indicate that the microhardness of the weld zone is better than that of the base meta1. A fine-grained weld region has been observed and no obvious heat-affected zone is found. The fusion zone mainly consists of small α-Mg phase and β-Mg17A112. The small grains and β phases in the joint are believed to play an important role in the increase of the strength of weld for AZ61 magnesium alloys.

Effect of Post Weld Heat Treatment on Al 5052-SS 316 Explosive Cladding with Copper Interlayer

2018 ◽  
Vol 910 ◽  
pp. 35-40
Author(s):  
Eswaran Elango ◽  
Somasundaram Saravanan ◽  
Krishnamorthy Raghukandan
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Intermetallic Compounds ◽  
Microstructural Characterization ◽  
Optical Microscope ◽  
Post Weld Heat Treatment ◽  
Inclination Angles ◽  
Copper Interlayer ◽  
Weld Heat

This study focuses on effect of post weld heat treatment (PWHT) on interfacial and mechanical properties of Al 5052-SS 316 explosive clad with copper interlayer at varied loading ratios and inclination angles. The use of interlayer is proposed for the control of additional kinetic energy dissipation and to alleviate the formation of intermetallic compounds at the interface. The Al-Steel clads are subjected to PWHT at varied temperatures (300°C-450°C) for 30 minutes and the results are presented. The microstructural characterization of as-clad and PWHT samples is observed by an optical microscope and Scanning Electron Microscope (SEM). Maximum hardness is obtained at the interface of the as-clad and PWHT samples. Increase in PWHT temperature enhances the tensile strength of the composite, whereas, the tensile strength decreases at 300°C due to the diffusion of Al and Cu elements and the formation of detrimental intermetallic compounds.

Sign in / Sign up

Export Citation Format

Share Document