scholarly journals Streaming Birefringence - A Step Forward

2008 ◽  
Vol 13-14 ◽  
pp. 23-28 ◽  
Author(s):  
T. Spalton ◽  
Rachel A Tomlinson ◽  
A.E. Garrard ◽  
S.B.M. Beck
Keyword(s):  
Fluid Dynamics ◽  
Aqueous Solution ◽  
Flow Field ◽  
Cfd Simulation ◽  
Three Dimensional ◽  
Shear Stresses ◽  
Cfd Simulations ◽  
Full Field ◽  
Phase Stepping ◽  
Computational Fluid Dynamics Cfd

An investigation into three dimensional fluid flow has been conducted which combines the use of Computational Fluid Dynamics (CFD) simulations with the experimental phenomenon of Streaming Birefringence. A versatile flow channel was designed and built for use in conjunction with a circular polariscope. The experimental liquid used was an aqueous solution of a dye, commercially known as Milling Yellow NGS with the addition of Sodium Chloride. To extract the flow fields, six image phase stepping photoelasticity was used over backward and forward steps, and flows around a cylinder, and full-field fringe data were obtained. This method needs laminar flow regimes and the Reynolds number of the flow was around 10. To allow direct comparisons of the CFD solutions with the optical results, a macro (UDF) was written to interpret the flow field results from a (FLUENT6) CFD simulation. This integrated the shear stresses across the flow field and banded the results into fringes. A good correlation between the simulated fringes and the shearstrain rate was obtained from these observations.

Transient CFD Visualization of Fossil Fuel Combustion Simulations

2003 ◽  
Author(s):  
Brian Dotson ◽  
Kent Eshenberg ◽  
Chris Guenther ◽  
Thomas O’Brien
Keyword(s):  
Power Plants ◽  
High Efficiency ◽  
Cfd Simulation ◽  
Low Cost ◽  
Three Dimensional ◽  
Cfd Simulations ◽  
Projection System ◽  
Computational Fluid Dynamics Cfd ◽  
High Level ◽  
Wall System

The design of high-efficiency lower-emission coal-fed power plants is facilitated by the extensive use of computational fluid dynamics (CFD) simulations. This paper describes work conducted at the National Energy Technology Laboratory (NETL) and Pittsburgh Supercomputing Center (PSC) to provide an environment for the immersive three-dimensional visualization of CFD simulation results. A low-cost high-resolution projection system has been developed in the visualization lab at NETL. This multi-wall system consists of four projection screens, three of which are tiled into four quadrants. The graphics for the multi-wall system are rendered using a cluster of eight personal computers. A high-level visualization interface named Mavis has also been developed to combine the powerful 3D modules of OpenDX with methods developed at NETL for studying multiphase CFD data. With Python, a completely new OpenDX user interface was built that extends and simplifies the features of a basic graphics library.

The Design of Refinement Criteria for Dynamic Grid Adaptation Applied to Airfoil Flow Modeling

2003 ◽  
Author(s):  
Melih Demir ◽  
Govert de With ◽  
Arne E. Holdo̸
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Unsteady Flow ◽  
Mesh Refinement ◽  
Research Centre ◽  
Shear Stresses ◽  
Wall Region ◽  
Grid Adaptation ◽  
Computational Fluid Dynamics Cfd

At present a large number of fluid dynamics applications are found in aerospace, civil and automotive engineering, as well in medical related fields. In many applications the flow field is turbulent and the computational modelling of such flows remains a difficult task. To resolve all turbulent flow phenomena for flow problems where turbulence is of key interest is a priori not feasible in a Computational Fluid Dynamics (CFD) investigation with a conventional mesh. The use of a Dynamic Grid Adaptation (DGA) algorithm in a turbulent unsteady flow field is an appealing technique which can reduce the computational costs of a CFD investigation. A refinement of the numerical domain with a DGA algorithm requires reliable criteria for mesh refinement which reflect the complex flow processes. At present not much work has been done to obtain reliable refinement criteria for turbulent unsteady flow. The purpose of the work is to implement a new refinement technique for the boundary layer in the vicinity of the wall. It is aimed to model the flow around an airfoil with a LES turbulence model and a new DGA algorithm. In addition to that several simulations have been carried out for parametric studies. In these studies the incompressible solver in REACFLOW has been used. This Computational Fluid Dynamics (CFD) code REACFLOW was developed in collaboration with the joint Research Centre (JRC) in Italy. The following aims are aspired: • A new mesh refinement criteria method suitable for boundary layers; • To carry out LES simulations to establish the performance of the refinement criteria. The new criteria which are created in this work are for the near wall region. This criteria uses the wall shear stresses for the refinement technique. For the main flow stream the refinement criteria proposed by de With et al [6] will be used.

Optimze the Structure of Impeller for Stirred Bioreactor

2013 ◽  
Vol 694-697 ◽  
pp. 148-153 ◽  
Author(s):  
Li Kuan Zhu ◽  
Bo Yan Song ◽  
Zhen Long Wang ◽  
Yu Kui Wang
Keyword(s):  
Fluid Dynamics ◽  
Flow Field ◽  
Shear Force ◽  
Large Scale ◽  
Cfd Simulation ◽  
Simulation Method ◽  
Stirred Bioreactor ◽  
Anticlockwise Rotation ◽  
Computational Fluid Dynamics Cfd ◽  
Large Scale Culture

This paper mainly makes comparative analysis on four main types of blade in stirred bioreactor by Computational Fluid Dynamics(CFD) simulation. Firstly we establish simulation method suited for stirred bioreactor, then simulate the velocity and shear force of flow field in the bioreactor. No matter from flow field mixing or shear force aspect, Elephant Ear blades is the most suitable for cell large scale culture. At last, it optimizes the installation method and angle of Elephant Ear blades. It concludes that anticlockwise rotation and 45°installation angle is the optimum.

Extent, capacity and possibilities of computational fluid dynamics as a design tool for pump intakes: a review

2018 ◽  
Vol 18 (5) ◽  
pp. 1518-1530 ◽  
Author(s):  
Jie Zhang ◽  
Tien Yee
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Three Dimensional ◽  
Design Tool ◽  
Cfd Modeling ◽  
Cfd Simulations ◽  
Pump Station ◽  
Computational Fluid Dynamics Cfd ◽  
Future Direction ◽  
Computational Resources

Abstract Flow near pump intakes is three-dimensional in nature, and is affected by many factors such as the geometry of the intake bay, uniformity of approach flow, critical submergence, placements and operation combinations of pumps and so on. In the last three decades, advancement of numerical techniques coupled with the increase in computational resources made it possible to conduct computational fluid dynamics (CFD) simulations on pump intakes. This article reviews different aspects involved in CFD modeling of pump station intakes, outlines the challenges faced by current CFD modelers, and provides an attempt to forecast future direction of CFD modeling of pump intakes.

Optimization of CFD Meshing for Stented Vessel Geometries

2014 ◽  
Vol 553 ◽  
pp. 373-378 ◽  
Author(s):  
Azadeh Lotfi ◽  
Tracie J. Barber
Keyword(s):  
Cfd Simulation ◽  
Computational Cost ◽  
Three Dimensional ◽  
Coronary Bifurcation ◽  
Cfd Simulations ◽  
Coronary Stent Implantation ◽  
Bifurcation Stenting ◽  
Computational Fluid Dynamics Cfd ◽  
Blood Flow Patterns ◽  
High Computational Cost

Coronary stent implantation is the most widely used technique currently employed to treat atherosclerosis in coronary artery. Although the optimal technique for bifurcation stenting in terms of clinical outcome is still open to controversy, most previous studies have focused on the single-stenting techniques due to its simpler geometry and easier clinical implantation. While the biomedical environment in a stented coronary bifurcation is extremely challenging to model, Computational Fluid Dynamics (CFD) investigations have been used to study the effect of stent on blood flow patterns, however, in CFD simulation of double-stenting techniques, the presence of two or more stents accentuates the complexity of the geometry and the associated meshes especially in the region where two or multiple stent layers come together. Hence, in this study, complex three-dimensional geometric CFD simulations of a stented vessel have been performed in order to adopt an efficient and optimal meshing method to reduce the high computational cost. In doing so, several meshing strategies were chosen and applied.

scholarly journals Optimization and Application of D850 Dredge Pump Blades under Medium Coarse Sand Condition of Cutter Suction Dredger

2021 ◽  
Vol 2097 (1) ◽  
pp. 012005
Author(s):  
Haifei Zhuang ◽  
Mingming Liu ◽  
Yongding Wu
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Uniform Distribution ◽  
Fuel Consumption ◽  
Cfd Simulation ◽  
Coarse Sand ◽  
Solid Particles ◽  
Data Comparison ◽  
Computational Fluid Dynamics Cfd

Abstract Regarding wear issues of a dredge pump’s impeller as a cutter suction dredger transports medium coarse sand slurry, blades of the D850 dredge pump are modified and optimized, which extends the distance from the blade inlet root to the impeller suction and avoids damages of the impeller suction anti-wear ring. Analyses via computational fluid dynamics (CFD) simulation show that the head and the efficiency after blade modification have little changes compared with before optimization in the construction flow range of 10000-12000 m3/h under coarse sand condition. While it improves the flow field of impeller’s channels, decreases the vortex at the inlet root of the blades, ensures more uniform distribution of the solid particles. Meanwhile, this is beneficial to reductions of the channels’ wears. Applications from constructions show some improvements in the wears of the blade root. Through the construction data comparison, after replacing the modified impeller, dredging productivity will be increased by 15.1% and the fuel consumption per 10000 m3 will be then reduced by 11.5%.

scholarly journals CFD Simulation of Knock Onset in a Heavy-Duty Spark Ignition Gas Engine

2019 ◽  
Vol 8 (4) ◽  
pp. 9585-9593
Keyword(s):  
Fluid Dynamics ◽  
Numerical Model ◽  
Cfd Simulation ◽  
Combustion Process ◽  
Three Dimensional ◽  
Spark Ignition ◽  
Heavy Duty ◽  
Gas Engine ◽  
Optimization Study ◽  
Computational Fluid Dynamics Cfd

The paper describes a method for evaluating knocking onset with computational fluid dynamics (CFD) numerical model of the combustion process of spark ignited (SI) gas engine and methods for assessing the probability of knocking combustion based on this model. The probability of knocking combustion, which characterizes the boundary condition between normal combustion and knocking, is determined (8%). An optimization study of the influence of adjustment parameters on the probability of knocking based on a three-dimensional numerical model is carried out. The developed and tested technique allows one to monitor the tendency of the influence of various adjustment parameters on the probability of knocking in a SI gas engine.

Research of 3D-CFD Simulation on a Large Sized Pit Type Carburizing Furnace

2006 ◽  
Vol 118 ◽  
pp. 337-342
Author(s):  
Wei Min Zhang ◽  
Ye Ma ◽  
Lin Lin Li
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Gas Flow ◽  
Cfd Simulation ◽  
Fluid Dynamic ◽  
Cfd Simulations ◽  
3 Dimensional ◽  
Set Up ◽  
Carburizing Process

A fluid dynamic model was set up to describe the flow field of gas in a large sized pit type carburizing furnace when large sized gears were being carburized. The commercial software Fluent was adopted to carry out 3 dimensional computational fluid dynamics (3D-CFD) simulations of the gas flow field under different, actually four kinds of , furnace designs in this article. The flow fields of the carburizing gas around the part were analyzed. According to the simulations and analysis, it was shown that the number of fans on gear’s carburizing is not a primary factor, using a air inducting tub can improve the carburizing process significantly and proper loading tray design can also be positive. The results indicate that the simulation provides a reference to the furnace’s design optimization.

Off Set Strip Fins Thermo Hydraulic Performance Analysis Through CFD Simulation

2013 ◽  
Author(s):  
Guisselle Polo ◽  
Antonio Bula
Keyword(s):  
Fluid Dynamics ◽  
Cfd Simulation ◽  
Computational Simulation ◽  
Three Dimensional ◽  
Hydraulic Performance ◽  
Constant Flow ◽  
Uniform Temperature ◽  
Colburn Factor ◽  
Computational Fluid Dynamics Cfd ◽  
And Performance

A computational simulation of the thermo hydraulic performance of a trapezoidal Off Set Strip Fin (OSF) is performed. The simulations are carried for Reynolds number ranging from 300 to 9000 considering three-dimensional conditions (3D). Calculations were developed assuming a constant flow. Colburn factor j, and the friction factor f, were calculated. Uniform temperature condition is assumed at the solid surface and at the inlet. The results have been compared with studies made by Kays and London, (1984), Manglik and Bergles (1990), and Muzychka and Yovanovich, (2001). According to the obtained results, it can be concluded that Computational Fluid Dynamics (CFD) is able to explore the behavior and performance of this kind of fin, showing that the hydraulic performance is well represented by correlations widely used in literature, while thermal performance seems to be under predicted.

Sign in / Sign up

Export Citation Format

Share Document