Studies on Dynamic Response of Subway Tunnels with Initial Defect under Long-Term Train Loads

2012 ◽  
Vol 226-228 ◽  
pp. 1005-1009
Author(s):  
Fei Dong ◽  
Jun Dong ◽  
Wei Ze Sun
Keyword(s):  
Numerical Simulation ◽  
Dynamic Response ◽  
Fatigue Damage ◽  
Structural Damage ◽  
Side Wall ◽  
Subway Construction ◽  
Subway Tunnels ◽  
Initial Cracks ◽  
Deterioration Characteristics

Based on the background of a subway construction project, deterioration characteristics of the existed subway tunnels under long-term train loads is studied by using the method of stiffness discount which could reflect fatigue damage of the structure. Firstly, dynamic response of the tunnel with initial defects caused by approaching construction under long-term train loads is analyzed according numerical simulation, and some results under different degrees of fatigue are obtained. Then, numerical results of acceleration responses at such different points as the upper vault, the side wall and the bottom of tunnels in two directions, are compared with each other while the train loads are applied at the left tunnel, especially under three different stiffness. Our investigation shows local structural damage in the position with initial cracks will be caused by a high cycle stress although there are fewer influences of stiffness changes on dynamic response of tunnels.

Efficient Probabilistic Fatigue Analysis of a Riser Suspended and Moored by Chains

2015 ◽  
Author(s):  
Juan S. M. Giraldo ◽  
Luis V. S. Sagrilo ◽  
Claudio M. S. Dantas
Keyword(s):  
Numerical Simulation ◽  
Fatigue Damage ◽  
Asymptotic Approximation ◽  
Fatigue Analysis ◽  
Direct Integration ◽  
Brute Force ◽  
Offshore Structure ◽  
Huge Number ◽  
Stress Spectrum

Fatigue analysis of an offshore structure usually requires the numerical simulation of a huge number of loading cases to compute the long-term integral associated to the accumulated fatigue damage. Papadimitriou et al. [1] and Low and Cheung [2] proposed two distinct approaches to solve the long-term fatigue damage more efficiently. These methods are known as Asymptotic Approximation Method and Perturbation Method, respectively. This paper investigates the efficiency of these two methods in the fatigue analysis of the steel pipe of a riser suspended and moored by chains (RSAA). Since there is an analytical solution for the stress spectrum of this riser, both time and frequency domain fatigue assessments approaches are considered. The accuracy and computational efficiency of the aforementioned methods are compared with the “brute force” direct integration methodology.

scholarly journals Calibration of Finn Model and UBCSAND Model for Simplified Liquefaction Analysis Procedures

2021 ◽  
Vol 11 (11) ◽  
pp. 5283
Author(s):  
Jui-Ching Chou ◽  
Hsueh-Tusng Yang ◽  
Der-Guey Lin
Keyword(s):  
Numerical Simulation ◽  
Constitutive Model ◽  
Structural Damage ◽  
Simulation Analysis ◽  
Constitutive Models ◽  
Soil Liquefaction ◽  
Analysis Procedure ◽  
Liquefaction Resistance ◽  
Simplified Procedure ◽  
Liquefaction Analysis

Soil-liquefaction-related hazards can damage structures or lead to an extensive loss of life and property. Therefore, the stability and safety of structures against soil liquefaction are essential for evaluation in earthquake design. In practice, the simplified liquefaction analysis procedure associated with numerical simulation analysis is the most used approach for evaluating the behavior of structures or the effectiveness of mitigation plans. First, the occurrence of soil liquefaction is evaluated using the simplified procedure. If soil liquefaction occurs, the resulting structural damage or the following mitigation plan is evaluated using the numerical simulation analysis. Rational and comparable evaluation results between the simplified liquefaction analysis procedure and the numerical simulation analysis are achieved by ensuring that the liquefaction constitutive model used in the numerical simulation has a consistent liquefaction resistance with the simplified liquefaction analysis procedure. In this study, two frequently used liquefaction constitutive models (Finn model and UBCSAND model) were calibrated by fitting the liquefaction triggering curves of most used simplified liquefaction analysis procedures (NCEER, HBF, JRA96, and T-Y procedures) in Taiwan via FLAC program. In addition, the responses of two calibrated models were compared and discussed to provide guidelines for selecting an appropriate liquefaction constitutive model in future projects.

Implementation of a Method for Free-Spanning Pipeline Analysis

2021 ◽  
Author(s):  
Joannes Gullaksen
Keyword(s):  
Dynamic Response ◽  
Flow Direction ◽  
Limit State ◽  
Cross Flow ◽  
Ultimate Limit State ◽  
Force Model ◽  
Short Term ◽  
Direct Wave ◽  
Current Loading

Abstract The scope of this paper is to provide a method implemented in an application for assessment of dynamic response of free spanning pipelines subjected to combined wave and current loading. The premises for the paper are based on application development within pipeline free span evaluation in a software development project. A brief introduction is provided to the basic hydrodynamic phenomena, principles and parameters for dynamic response of pipeline free spans. The choice of method for static and dynamic span modelling has an influence on calculated modal frequencies and associated stresses. Due to the importance of frequencies and stresses for fatigue and environmental loading calculations, the choice of analysis approach influences the partial safety factor format. The aim of the structural analysis is to provide the necessary input to the calculations of VIV and force model response, and to provide realistic estimations of static loading from functional loads. Environmental flow conditions are implemented in the application, such as steady flow due to current, oscillatory flow due to waves and combined flow due to current and waves. Combined wave and current loading include the long-term current velocity distribution, short-term and long-term description of wave-induced flow velocity amplitude and period of oscillating flow at the pipe level and return period values. Inline and cross-flow vibrations are considered in separate response models. For pipelines and risers, modes are categorized in in-line or cross-flow direction. A force model is also considered for the short-term fatigue damage due to combined current and direct wave actions. Design criteria can be specified for ultimate limit state (ULS) and fatigue limit state (FLS) due to in-line and cross-flow vortex induced vibrations (VIV) and direct wave loading.

Numerical Simulation of Ship Collision and Validations With Experimental Results

2021 ◽  
Author(s):  
Xiangbiao Wang ◽  
Chun Bao Li ◽  
Ling Zhu
Keyword(s):  
Numerical Simulation ◽  
Model Test ◽  
Structural Damage ◽  
Added Mass ◽  
Ship Motion ◽  
Time Dependent ◽  
Structural Deformation ◽  
Structure Interaction ◽  
Ship Collision ◽  
Good Agreement

Abstract Ship collision accidents occur from time to time in recent years, and this would cause serious consequences such as casualties, environmental pollution, loss of cargo on board, damage to the ship and its equipment, etc. Therefore, it is of great significance to study the response of ship motion and the mechanism of structural damage during the collision. In this paper, model experiments and numerical simulation are used to study the ship-ship collision. Firstly, the Coupled Eulerian-Lagrangian (CEL) was used to simulate the fluid-structure interaction for predicting structural deformation and ship motion during the normal ship-ship collision. Meanwhile, a series of model tests were carried out to validate the numerical results. The validation presented that the CEL simulation was in good agreement with the model test. However, the CEL simulation could not present the characteristics the time-dependent added mass.

Numerical simulation of fire smoke in extra-long river-crossing subway tunnels

2018 ◽  
Vol 82 ◽  
pp. 82-98 ◽  
Author(s):  
Xinxin Guo ◽  
Xuhai Pan ◽  
Zhilei Wang ◽  
Juan Yang ◽  
Min Hua ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Fire Smoke ◽  
Subway Tunnels

Impact Simulation of a Crashworthy Composite Fuselage Section with Energy-Absorbing Floor

2014 ◽  
Vol 529 ◽  
pp. 102-107
Author(s):  
Hai Bo Luo ◽  
Ying Yan ◽  
Xiang Ji Meng ◽  
Tao Tao Zhang ◽  
Zu Dian Liang
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Dynamic Response ◽  
Relative Error ◽  
High Strength ◽  
Computer Code ◽  
Impact Simulation ◽  
Average Acceleration ◽  
Simulation Results ◽  
Energy Absorbing

A 7.8m/s vertical drop simulate of a full composite fuselage section was conducted with energy-absorbing floor to evaluate the crashworthiness features of the fuselage section and to predict its dynamic response to dummies in future. The 1.52m diameter fuselage section consists of a high strength upper fuselage frame, one stiff structural floor and an energy-absorbing subfloor constructed of Rohacell foam blocks. The experimental data from literature [6] were analyzed and correlated with predictions from an impact simulation developed using the nonlinear explicit transient dynamic computer code MSC.Dytran. The simulated average acceleration did not exceed 13g, by contrast with experimental results, whose relative error is less than 11%. The numerical simulation results agree with experiments well.

Sign in / Sign up

Export Citation Format

Share Document