Study of Variation of Soil Stress State Based on the Curve of Normalized Strain- Pore Water Pressure

2013 ◽  
Vol 275-277 ◽  
pp. 295-298
Author(s):  
Gang Yang ◽  
Qing Yang ◽  
Wen Hua Liu
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Cyclic Stress ◽  
Cyclic Stress Ratio ◽  
Cycle Number ◽  
Soil Stress ◽  
Critical Cyclic Stress Ratio ◽  
Versus Strain

The cyclic behavior of normally consolidated silty clays was investigated by conducting a series of cyclic simple shear tests on one-dimensionally and isotropically consolidated reconstituted samples. The critical cyclic stress ratio was obtained by the normalized axial strain. Based on hysteretic curve of pore water pressure versus strain, dynamic characteristics of silty clay were investigated. The results showed that with increasing of cyclic loading, soil stress state can be divided into steady state, critical state and failure state based on the critical cyclic stress ratio. The hysteresis curve of pore water pressure versus strain was divided into two parts by cross point A. Compared with two parts, the variation law was obtained. When the upper part area was bigger than the lower part area, pore water pressure and axial strain continuously increase with cycle number; when the upper part area was smaller than the lower part area, pore water pressure and axial strain tended to be steady with cycle number.

scholarly journals Effect of Variable Confining Pressure on Cyclic Triaxial Behavior of K0-consolidated Soft Marine Clay

2018 ◽  
Vol 4 (4) ◽  
pp. 755
Author(s):  
Lei Sun
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Confining Pressure ◽  
Stress Path ◽  
Cyclic Stress ◽  
Marine Clay ◽  
Stress Ratios ◽  
Variable Confining Pressure

The effect of variable confining pressure (VCP) on the cyclic deformation and cyclic pore water pressure in K0-consolidated saturated soft marine clay were investigated with the help of the cyclic stress-controlled advanced dynamic triaxial test in undrained condition. The testing program encompassed three cyclic deviator stress ratios, CSR=0.189, 0.284 and 0.379 and three stress path inclinations ηampl=3,1 and 0.64. All tests with constant confining pressure (CCP) and variable confining pressure (VCP) have identical initial stress and average stress. The results were analyzed in terms of the accumulative normalized excess pore water pressure rqu recorded at the end of each stress cycle and permanent axial strain, as well as resilient modulus. Limited data suggest that these behavior are significantly affected by both of the VCP and CSR. For a given value of VCP, both of the pore water pressure rqu and permanent axial strains are consistently increase with the increasing values of CSR. However, for a given value of CSR, the extent of the influence of VCP and the trend is substantially depend on the CSR.

Experimental Study on the Dynamic Characteristics of Saturated Soft Clay Under Bi-Directional Cyclic Loading

2010 ◽  
Author(s):  
Gong-xun Liu ◽  
Mao-tian Luan ◽  
Xiao-wei Tang ◽  
Qing Yang
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Clay ◽  
Cyclic Strain ◽  
Stress Path ◽  
Cyclic Stress ◽  
Cycle Number ◽  
Cyclic Shear ◽  
Saturated Soft Clay

A series of stress-controlled bi-directional cyclic shear tests under isotropic consolidation conditions were conducted for simulating the cyclic stress induced by wave loading. The area bounded by the elliptical stress path was kept unchanged, while the ratio (R) of the axial cyclic shear stress and the torsional cyclic shear stress was changed in order to research the effect of varied two cyclic stress components on the pore water pressure, strength and deformation behaviors of saturated soft clay. The test results show that with a decrease in R, the residual pore water pressure decreases at first and then increases, and it reaches the lowest at R=1 at the same cycle number, while the amplitude of fluctuated pore water pressure decreases all along. The relationship curves between normalized ratio of pore water pressure and ratio of cycle number have significant differences with different R. The cycle number at failure increases at first and then decreases with decreasing R. It reaches the maximum at R=1, indicating that the dynamic strength is the highest when the stress path is close to a circle. The dynamic stress-strain relationship curves with different R indicate that both the axial and the torsional strains caused by the bi-directional cyclic loadings are mainly the cyclic strains, at the same time, the residual strains appear. With decreasing R, the amplitude of axial cyclic strain decreases and the ratio of axial residual strain and cyclic strain increases firstly and then decreases, while the amplitude of torsional cyclic strain increases. The cyclic shear strain is basically symmetric at R=1, while the residual shear strains appear under other conditions.

scholarly journals Undrained monotonic and cyclic shear response and particle crushing of silica sand at low and high pressures

2017 ◽  
Vol 54 (2) ◽  
pp. 207-218 ◽  
Author(s):  
Masayuki Hyodo ◽  
Yang Wu ◽  
Noritaka Aramaki ◽  
Yukio Nakata
Keyword(s):  
Pore Water ◽  
Stress Ratio ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Confining Pressure ◽  
Cyclic Stress ◽  
Silica Sand ◽  
Particle Crushing ◽  
Cyclic Stress Ratio ◽  
Confining Pressures

A series of undrained monotonic and cyclic triaxial tests were performed on silica sand at two initial densities and different confining pressures from 0.1 to 5 MPa to investigate their shear response and crushing behaviour. The influence of particle crushing on the undrained shear strength and pore-water pressure was examined. To clarify the evolution of particle crushing, undrained monotonic and cyclic tests were terminated at several distinctive stages and sieving analysis tests were subsequently performed on the tested specimens. In the undrained monotonic test, specimens exhibited remarkable dilation behaviour and experienced no apparent particle crushing at low confining pressures. An increase in the mean stress suppressed the dilatancy due to a faster increase of the pore-water pressure, giving rise to the occurrence of particle crushing. In the undrained cyclic test, a higher confining pressure and cyclic stress ratio resulted in a much higher relative breakage. At a specific cyclic stress ratio, the relative breakage increased as the cyclic loading progressed. The confining pressure and shear strain amplitude played a significant role in controlling the evolution of particle breakage. The correlation between the relative breakage and plastic work for specimens under isotropic consolidation, undrained monotonic, and cyclic loadings has been validated experimentally.

scholarly journals Mechanical response and pore pressure generation in granular filters subjected to uniaxial cyclic loading

2018 ◽  
Vol 55 (12) ◽  
pp. 1756-1768
Author(s):  
Jahanzaib Israr ◽  
Buddhima Indraratna
Keyword(s):  
Cyclic Loading ◽  
Pore Pressure ◽  
Pore Water ◽  
Mechanical Response ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Internal Erosion ◽  
Excess Pore Water Pressure ◽  
Excess Pore

This paper presents results from a series of piping tests carried out on a selected range of granular filters under static and cyclic loading conditions. The mechanical response of filters subjected to cyclic loading could be characterized in three distinct phases; namely, (I) pre-shakedown, (II) post-shakedown, and (III) post-critical (i.e., the occurrence of internal erosion). All the permanent geomechanical changes such, as erosion, permeability variations, and axial strain developments, took place during phases I and III, while the specimen response remained purely elastic during phase II. The post-critical occurrence of erosion incurred significant settlement that may not be tolerable for high-speed railway substructures. The analysis revealed that a cyclic load would induce excess pore-water pressure, which, in corroboration with steady seepage forces and agitation due to dynamic loading, could then cause internal erosion of fines from the specimens. The resulting excess pore pressure is a direct function of the axial strain due to cyclic densification, as well as the loading frequency and reduction in permeability. A model based on strain energy is proposed to quantify the excess pore-water pressure, and subsequently validated using current and existing test results from published studies.

scholarly journals Numerical Study on Effects of the Embedded Monopile Foundation on Local Wave-Induced Porous Seabed Response

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
Chi Zhang ◽  
Qingyang Zhang ◽  
Zaitian Wu ◽  
Jisheng Zhang ◽  
Titi Sui ◽  
...  
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Numerical Study ◽  
Water Pressure ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Stokes Wave ◽  
Local Concentration ◽  
Soil Stress ◽  
Local Wave

Effects of the embedded monopile foundation on the local distributions of pore water pressure, soil stresses, and liquefaction are investigated in this study using a three-dimensional integrated numerical model. The model is based on a Reynolds-Averaged Navier-Stokes wave module and a fully dynamic poroelastic seabed module and has been validated with the analytical solution and experimental data. Results show that, compared to the situation without an embedded foundation, the embedded monopile foundation increases and decreases the maximum pore water pressure in the seabed around and below the foundation, respectively. The embedded monopile foundation also significantly modifies the distributions of the maximum effective soil stress around the foundation and causes a local concentration of soil stress below the two lower corners of foundation. A parametric study reveals that the effects of embedded monopile foundation on pore water pressure increase as the degrees of saturation and soil permeability decrease. The embedded monopile foundation tends to decrease the liquefaction depth around the structure, and this effect is relatively more obvious for greater degrees of saturation, greater soil permeabilities, and smaller wave heights.

scholarly journals Effect of Wetting-Drying Cycle on the Deformation and Seepage Behaviors of Rock Masses around a Tunnel

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Qingzhen Guo ◽  
Haijian Su ◽  
Hongwen Jing ◽  
Wenxin Zhu
Keyword(s):  
Rock Mass ◽  
Principal Stress ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Inrush ◽  
Surrounding Rock ◽  
Tunnel Excavation ◽  
Cycle Number ◽  
Simulation Results

Water inrush caused by the wetting-drying cycle is a difficult problem in tunnel excavation. To investigate the effect of the wetting-drying cycle on the stability of the tunnel surrounding rock, physical experiments and numerical simulations regarding the process of tunnel excavation with different wetting-drying cycle numbers were performed in this study. The evolutions of stress, displacement, and pore water pressure were analyzed. With the increase in cycle number, the pore water pressure, vertical stress, and top-bottom approach of the tunnel surrounding rock increase gradually. And the increasing process could be divided into three stages: slightly increasing stage, slowly increasing stage, and sharply increasing stage, respectively. The failure process of the surrounding rock under the wetting-drying cycle gradually occurs from the roof to side wall, while the baseplate changes slightly. The simulation results showed that the maximum principal stress in the surrounding rock mass of the tunnel increases, while the minimum principal stress decreases. Furthermore, the displacement of the rock mass decreases gradually with the increasing distance from the tunnel surface. By comparing the simulation results with the experimental results, well consistency is shown. The results in this study can provide helpful references for the safe excavation and scientific design of a tunnel under the wetting-drying cycle.

EXPERIMENT STUDY ON DYNAMIC STRENGTH OF LOESS UNDER REPEATED LOAD

2008 ◽  
Vol 22 (31n32) ◽  
pp. 5825-5830 ◽  
Author(s):  
ZHENGHUA XIAO ◽  
BO HAN ◽  
HONGJIAN LIAO ◽  
AKENJIANG TUOHUTI
Keyword(s):  
Shear Strength ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Dynamic Strength ◽  
Triaxial Tests ◽  
Dynamic Shear ◽  
Anisotropic Consolidation ◽  
Dynamic Shear Strength

A series of dynamic triaxial tests are performed on normal anisotropic consolidation and over anisotropic consolidation specimens of loess. Based on the test results, the variable regularity of dynamic shear stress, axial strain and pore water pressure of loess under dynamic loading are measured and analyzed. The influences of the dynamic shear strength and pore water pressure at different over consolidation ratio are analyzed. The relationship between dynamic shear strength and over consolidation ratio of loess is obtained. The evaluating standard of dynamic shear strength of loess is discussed. Meanwhile, how to determine the effective dynamic shear strength index of normal anisotropic consolidated loess is also discussed in this paper. Several obtained conclusions can be referenced for studying the dynamic shear strength of loess foundation.

Soil Liquefaction Assessment by Anisotropic Cyclic Triaxial Test

2018 ◽  
pp. 631-664
Author(s):  
Koray Ulamis
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Sandy Soils ◽  
Soil Liquefaction ◽  
Cyclic Triaxial ◽  
Loading Case ◽  
Anisotropic Consolidation ◽  
Assessment Standard

Liquefaction of saturated sandy soils is one of the most significant aspects of earthquake triggered natural hazards. The main mechanism deals with the loss of effective stress due to rapid pore water pressure generation during earthquake shaking. This chapter involves with the fundamental mechanism and impacts of liquefaction. Liquefaction susceptibility of geological environments are briefly represented for preliminary assessment. Standard procedures of liquefaction are summarized. The dynamic response of sands are also reviewed. A case of anisotropic loading is considered, using three different particle sized sands below a shallow footing. Such sandy soils are subjected to anisotropic consolidation before performing undrained cyclic triaxial testing along limited cycles. Variation of axial strain, pore water pressure and related parameters are investigated. Main outcome of this study is to review the initial liquefaction state of sands by anisotropic loading case.

scholarly journals Behavior of Nonplastic Silty Soils under Cyclic Loading

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Nazile Ural ◽  
Zeki Gunduz
Keyword(s):  
Pore Pressure ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Clay Content ◽  
Cyclic Stress ◽  
Excess Pore Pressure ◽  
Stress Ratios ◽  
Silty Soils ◽  
Excess Pore

The engineering behavior of nonplastic silts is more difficult to characterize than is the behavior of clay or sand. Especially, behavior of silty soils is important in view of the seismicity of several regions of alluvial deposits in the world, such as the United States, China, and Turkey. In several hazards substantial ground deformation, reduced bearing capacity, and liquefaction of silty soils have been attributed to excess pore pressure generation during dynamic loading. In this paper, an experimental study of the pore water pressure generation of silty soils was conducted by cyclic triaxial tests on samples of reconstituted soils by the slurry deposition method. In all tests silty samples which have different clay percentages were studied under different cyclic stress ratios. The results have showed that in soils having clay content equal to and less than 10%, the excess pore pressure ratio buildup was quicker with an increase in different cyclic stress ratios. When fine and clay content increases, excess pore water pressure decreases constant cyclic stress ratio in nonplastic silty soils. In addition, the applicability of the used criteria for the assessment of liquefaction susceptibility of fine grained soils is examined using laboratory test results.

Sign in / Sign up

Export Citation Format

Share Document