Research on Micromotor Dynamometer in Surgical Power Plant

2013 ◽  
Vol 303-306 ◽  
pp. 1748-1751
Author(s):  
Zhi Qiang Zhao ◽  
Cheng Liao
Keyword(s):  
Power Plant ◽  
Output Power ◽  
Data Gathering ◽  
Motor Speed ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Brushless Motor ◽  
Driver Circuit ◽  
Electronic Load ◽  
And Control

Micro-motor is the core component of surgical power plant, this paper research a new method of measuring micro-motor speed and output power. This system takes WTK-10 Groove-type photoelectric sensor and 6 gap speed code disc to measure micro-motor speed, uses TQ661 torque sensor to measure output torque of micro-motor, takes electronic load loading circuit, torque-speed measuring circuit, brushless motor driver circuit and control circuit of single chip microcomputer to realize the detection of micro-motor speed and output power, and to display results on PC. This system has the functions of data gathering, data processing, displaying and alarm etc, is accurate, economical and practical etc.

Study on the Temperature and Speed Test System

2012 ◽  
Vol 590 ◽  
pp. 333-336
Author(s):  
Qian Zhao ◽  
Shan Zhen Xu ◽  
Qi Chen ◽  
Cheng Wang
Keyword(s):  
Signal Processing ◽  
Data Acquisition ◽  
Data Acquisition System ◽  
Test System ◽  
Acquisition System ◽  
Motor Speed ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Signal Processing Circuit ◽  
Processing Circuit

A kind of multiple parameter data acquisition system was designed based on single-chip microcomputer which can realized the data acquisition of temperature and DC motor speed. The data acquisition system consists of sensor, signal processing circuit, single-chip microcomputer and LED digital tube. The speed signal is acquired by photoelectric sensor, put into the Single-chip microcomputer processed after processed by signal processing circuit, and displayed the value in the digital tubes. The temperature signal is acquired by digital sensor, and the Single-chip microcomputer can read the data directly. Through two independent keyboards, the test system realized the data acquisition and data switch displaying of the multiple parameters.

Design of Intelligent Living Room Environment’s Control System with Intelligent Materials

2013 ◽  
Vol 644 ◽  
pp. 3-7 ◽  
Author(s):  
Jun Yu ◽  
Yu Wen Zhai ◽  
Xiao Hong Li
Keyword(s):  
Control System ◽  
Comfort Level ◽  
Living Room ◽  
Intensity Level ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Measurement And Control System ◽  
And Control ◽  
Environment Parameters ◽  
Measurement And Control

The measurement and control system of an intelligent living room environment is introduced in this paper, which takes single-chip microcomputer STC89C52 as the core chip. The system uses the intelligent digital temperature and humidity materials SHT11 and light sensitive resistor to realize the detections of living room temperature, relative humidity and light intensity level with automatic control, in order to improve the living room comfort level. It's function reliable, simply constructed, and can achieve the automatic adjustment of living room environment parameters.

Adaptive Control Research and Design Based on STC Single-Chip Microcomputer

2012 ◽  
Vol 516-517 ◽  
pp. 1678-1682
Author(s):  
Qiang Xu ◽  
Qian Zhang ◽  
Kai Chun Ren ◽  
Xing Qi Zhang ◽  
Shi Gang Li
Keyword(s):  
Software Design ◽  
Lighting System ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Control Module ◽  
Control Research ◽  
Data Acquisition Module ◽  
And Control ◽  
Led Lights ◽  
Research And Design

This paper analyses the characteristics and the glowing use value of LED lights, using STC series microcontroller design a system of LED which can automatically adjust the light according to the environment changes. The control system consists by the data acquisition module and control module and circuit driver module. This paper gives the control circuit hardware and software design. This system has many advantages such as energy conservation and environmental protection and longevity when compared with the conventional lighting system.

N-C Lathe Cutting Force Measurement Research

2013 ◽  
Vol 457-458 ◽  
pp. 608-611
Author(s):  
Ming Xi Shao ◽  
Xiu Mei Zhang
Keyword(s):  
Cutting Force ◽  
Force Measurement ◽  
System Structure ◽  
Scale Transformation ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Cutting Force Measurement ◽  
Cnc Lathe ◽  
And Control ◽  
Measurement And Control

through the use of single-chip microcomputer measurement CNC lathe cutting force, this paper focuses on the single chip microcomputer to implement continuous automatic sampling, A/D conversion, scale transformation and data processing methods. Introduces the principle of the measurement and control system, structure and data acquisition part of the program.

The Design of Automatic Control Temperature System for Greenhouse

2014 ◽  
Vol 1006-1007 ◽  
pp. 662-665
Author(s):  
Yu Fan ◽  
Xue Feng Wu
Keyword(s):  
Temperature Sensor ◽  
Temperature Data ◽  
Digital Display ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Key Technology ◽  
Modern Agriculture ◽  
Temperature Environment ◽  
Growth Habits ◽  
And Control

In modern agriculture, greenhouse environment implementation of automatic detection and control is necessary. The key technology of greenhouse facilities is the temperature control. The microcontroller is core processor and the temperature sensor is used to collect temperature data, and transmitting the data to the single chip microcomputer, the data collected will be sent to the digital display, so that operator could observe the current temperature. It can adjust the temperature environment inside the greenhouse in the system and flexible to meet the plant growth habits.

Development of DSD from SCM to PC

2013 ◽  
Vol 475-476 ◽  
pp. 243-246
Author(s):  
Fu Ling Li ◽  
Xiu Ling He ◽  
Yong Li
Keyword(s):  
Data Storage ◽  
Storage Device ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Cmos Chip ◽  
And Control

A kind of device for data storage is realized in this article. The data storage device (DSD) has USB and I2C port. By it we can transmit data from terminal for measure and control that base on SCM (single-chip microcomputer) to PC easily. DSD use EEPROM CMOS chip AT24C512 for storing data, and use USB chip CH341 for transmitting data to PC. This article showed AT24C512, CH341 and the characteristic of I2C BUS. The hardware for taking data and software for communicating between terminal and PC were designed in this article.

scholarly journals DESIGN AND RESEARCH OF AUTOMATIC ALIGNMENT TEST DEVICE OF SEMI-FEEDING PEANUT COMBINE HARVESTER

2019 ◽  
Vol 57 (1) ◽  
pp. 71-80
Author(s):  
X.L. Lv ◽  
Z.L. Hu ◽  
S.Y. Wang ◽  
Z.Y. Yu ◽  
◽  
...  
Keyword(s):  
Forward Speed ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Test Device ◽  
Detection Mechanism ◽  
Hydraulic Flow ◽  
Alignment System ◽  
Automatic Alignment ◽  
Combine Harvester ◽  
And Control

For the caused harvesting loss problem by inaccurate alignment of the semi-feeding peanut harvester, an automatic alignment system on the control core of the single chip microcomputer μPD78F0525 was designed. The system adopts a four-bar detection mechanism to transmit the offset to the controller through the sensor and to adjust the excavator in time. On this basis, a peanut automatic alignment test device is developed, which is composed of conveying platform, ridge ditch, hydraulic execution system, signal detection mechanism, signal processing and control system, etc. The influence effect of the main factors of the system is tested through the test bench. The results show: the reaction time increases with the increase of spring preload and deviation distance, gradually decreases and tends to remain unchanged with the increase of forward speed, and first decreases and then increases with the increase of hydraulic flow. The unqualified rate first decreases and then increases with the increase of spring preload, gradually increases with the increase of forward speed and deviation distance, and gradually decreases with the increase of hydraulic flow. The effectiveness and stability of the automatic alignment system can meet the operation requirements. It effectively solved the problem of automatic alignment of the semi-feeding peanut harvester and provided a technical reference for the research and development of the automatic alignment system for harvesting the fruits under the soil.

Design of a Type of Cleaning Robot System

2012 ◽  
Vol 605-607 ◽  
pp. 1415-1418 ◽  
Author(s):  
Hao Peng ◽  
Zhi Cheng Huang
Keyword(s):  
Control System ◽  
Home Environment ◽  
Infrared Sensor ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Robot System ◽  
Working Environments ◽  
Cleaning Robot ◽  
Household Cleaning ◽  
And Control

A cleaning robot for household cleaning is designed based on the single chip microcomputer AT89S51. It can complete home environment clean in the case of unattended. With the help of the infrared sensor and the control system, the Cleaning robot can automatically avoid the static and dynamic obstacles in the working environments and clean the ground in the room. Practice has proved that its structure is compact, flexible, easy to implement and control and it can initially complete the obstacle avoidance and cleaning tasks.

Design on Height Interface Circuit for Atmosphere Computer

2011 ◽  
Vol 317-319 ◽  
pp. 1255-1258
Author(s):  
Min Sheng Hou
Keyword(s):  
Traffic Control ◽  
Electrical Power ◽  
Single Chip ◽  
Single Chip Microcomputer ◽  
Data Correlation ◽  
Interface Circuit ◽  
Driver Circuit ◽  
Digital Encoding ◽  
Level Converter ◽  
Height Data

In order to make Russian-made atmosphere computer can be connected the domestic ATC（Air Traffic Control） transponder, the interface circuit, consisted of single chip microcomputer, A/D converter, level converter, driver circuit, isolator and electrical power, is designed. The data correlation and anti-jamming techniques are adopted to simplify hardware and to enhance conversion precision of height data and anti-jamming performance of the system. The test shows that the interface circuit can convert the analog height signal to digital encoding signal fit the requirements for domestic ATC transponder.

Sign in / Sign up

Export Citation Format

Share Document