Dynamic Testing at High Strain Rates of AZ31 Magnesium Alloys on SHPB Equipment

2013 ◽  
Vol 303-306 ◽  
pp. 2648-2651
Author(s):  
Xu Qing Chang ◽  
Tie Hua Ma
Keyword(s):  
Strain Rate ◽  
Optical Microscopy ◽  
Strain Hardening ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Mg Alloy ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
High Strain Rates ◽  
Az31 Mg Alloy

The mechanical behaviour of as-cast AZ31 Mg alloy has been investigated at strain rates up to 2.0×103s-1. Dynamic tests were carried out at room temperature using a Split Hopkinson Pressure Bar (SHPB) apparatus. Microstructural characteristic were analysed by Image MAT A1 optical microscopy. The results demonstrated that AZ31 Mg alloy exhibited obvious yield phenomena and strain hardening behaviour at high strain rates. The basically same curvature of stress-strain curves exhibited an similar strain hardening rate. The dynamic yield strength changes little and the peak stress increases with the strain rates. An examination by optical microscopy after high strain rate deformation reveals the occurrence of twinning and twin area percentage increases with the strain rate increasing.

High Strain Rate Compression Testing of Hot-Pressed TRIP/TWIP-Matrix-Composites

2017 ◽  
Vol 742 ◽  
pp. 113-120 ◽  
Author(s):  
Ralf Eckner ◽  
Lutz Krüger
Keyword(s):  
Strain Rate ◽  
Strain Hardening ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Deformation Mechanisms ◽  
Strain Rates ◽  
Strengthening Effect ◽  
Matrix Composites ◽  
High Strain Rates ◽  
The Matrix

Metal matrix composites with ceramic reinforcements such as particles or fibers have come into focus during the past decades due to rising requirements on engineering materials. In this work, composite materials out of high-alloy CrMnNi-steel matrices with varying Ni-contents (3 wt.% and 9 wt.%) and 10 vol.% Mg-PSZ were processed by hot-pressing. The variation in Ni-content resulted in a change in stacking fault energy (SFE) which significantly influenced the deformation mechanisms. The mechanical behavior of the developed composites was investigated in a wide strain rate range between 0.0004 s-1 and 2300 s-1 under compressive loading. This was done by a servohydraulic testing system, a drop weight tower, and a Split-Hopkinson Pressure Bar for the high strain rates. To study the influence on the deformation mechanisms such as martensitic transformations and/or twinning, interrupted tests were also carried out at 25 % compressive strain. Subsequent microstructural examinations were done by a magnetic balance to measure the quantity of α’-martensite as well as by scanning electron microscopy (SEM). The results show an increase of strength and strain hardening with decreasing SFE of the matrix due to increased α’-martensite formation. The addition of the Mg-PSZ particles resulted in further strengthening over almost the entire deformation range for all investigated composites. At high strain rates quasi-adiabatic heating suppressed the martensite transformation and reduced the strain hardening capacity of the matrix. Nonetheless the particle reinforcement retains its strengthening effect.

High-strain-rate response of hot-explosively consolidated W–Ti alloys

1999 ◽  
Vol 14 (7) ◽  
pp. 2838-2848 ◽  
Author(s):  
Laszlo J. Kecskes ◽  
Ian W. Hall
Keyword(s):  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Spatial Location ◽  
Shear Localization ◽  
Full Density ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
High Strain Rates ◽  
The Matrix

Disk-shaped, two-phase, full-density W–Ti alloy billets have been fabricated by a new, hot-explosive-compaction technique. As part of a characterization effort, the compressive behavior of the alloy was investigated. Quasistatic and split Hopkinson pressure bar (SHPB) tests of cylindrical samples, taken from a 83W–17Ti at.% alloy billet, demonstrate the propensity of this material to fail via shear localization at high strain rates. The effects of strain rate, orientation of the matrix phase with respect to the direction of the SHPB compression, and spatial location within the billet (i.e., periphery or core) were evaluated. At quasistatic strain rates, the alloy deformed in a ductile mode and exhibited a definite spatial location sensitivity. At high strain rates, spatial location sensitivity was absent. Shear localization was unaffected by density variations, matrix orientation in the alloy, or the presence of coarsened substructural features in the matrix. These experiments and the microstructural characteristics of the resultant localized regions are discussed.

A Dynamic Mechanical Analysis of T2 Copper at High Strain Rates

2019 ◽  
Vol 812 ◽  
pp. 38-44
Author(s):  
Shuai Chen ◽  
Wen Bin Li ◽  
Xiao Ming Wang ◽  
Wen Jin Yao
Keyword(s):  
Yield Strength ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Pure Copper ◽  
Dislocation Slip ◽  
Strain Rates ◽  
High Strain Rates ◽  
Stress Strain ◽  
Shpb Test

This work compares the pure copper (T2 copper)’s stress-strain relationship at different strain rates in the uni-axial tension test and Split Hopkinson Pressure Bar (SHPB) test. Small samples were utilized in the high strain rate SHPB test in which the accuracy was modified by numerical simulation. The experimental results showed that the T2 copper’s yield strength at high strain rates largely outweighed the quasi static yield strength. The flow stress in the stress-strain curves at different strain rates appeared to be divergent and increased with the increase in strain rates, showing great strain strengthening and strain rate hardening effects. Metallographic observation showed that the microstructure of T2 copper changed from equiaxed grains to twins and the interaction between the dislocation slip zone grain boundary and twins promoted the super plasticity distortion in T2 copper.

High Strain Rate Compressive Behavior of Micro-Fibre Reinforced Fine Grained Cementitious Composite

2018 ◽  
Vol 276 ◽  
pp. 140-147
Author(s):  
Martina Drdlová ◽  
Miloslav Popovič ◽  
René Čechmánek
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Compressive Strain ◽  
Fibre Reinforcement ◽  
Strain Rates ◽  
Cementitious Composite ◽  
Compressive Behavior ◽  
Hopkinson Pressure Bar

This paper presents an experimental study on the high strain rate compressive behavior of micro-fibre reinforced ultrahigh performance cementitious composite, which is intended to be used as a matrix for slurry infiltrated fibre concrete (SIFCON). Cementitious composite specimens with 5 different types of microfibres, namely aramid, carbon, wollastonite, polypropylene and glass in amounts of 1.5-2.0% by volume were prepared and investigated. Split Hopkinson pressure bar (SHPB) equipment was used to determine the cementitious composite behavior at strain rates up to 1600 s-1. Quasistatic tests were performed, as well and ratios of these properties at high strain rates to their counterparts at static loading were compared. The dynamic increase factors were calculated. Strain rate sensitivity was observed - compressive strength was found to be increased with strain rate for all tested specimens. Peak stress values, critical compressive strain and post peak behaviour varies for specimens with different micro-fibre reinforcement, which allows to find the optimal reinforcement for high strain rate impacted structures.

Compressive Behavior of Plain and Fiber-Reinforced High-Strength Concrete Subjected to High Strain Rate Loading

2011 ◽  
Vol 82 ◽  
pp. 57-62 ◽  
Author(s):  
Sha Sha Wang ◽  
Min Hong Zhang ◽  
Ser Tong Quek
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strength Concrete ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Strain Rates ◽  
Compressive Behavior ◽  
High Strain Rates ◽  
Strength Concrete

This paper presents a laboratory experimental study on the effect of high strain rate on compressive behavior of plain and fiber-reinforce high-strength concrete (FRHSC) with similar strength of 80-90 MPa. Steel fibers, polyethylene fibers, and a combination of these were used in the FRHSC. A split Hopkinson pressure bar equipment was used to determine the concrete behavior at strain rates from about 30 to 300 s-1. The ratio of the strength at high strain rates to that at static loading condition, namely dynamic increase factor (DIF), of the concretes was determined and compared with that recommended by CEB-FIP code. Fracture patterns of the specimens at high strain rates are described and discussed as well. Results indicate that the CEB-FIP equation is applicable to the plain high strength concrete, but overestimates the DIF of the FRHSC at strain rates beyond a transition strain rate of 30 s-1. Based on the experimental results, a modified equation on DIF is proposed for the FRHSC.

Using Split Hopkinson Pressure Bars to Perform Large Strain Compression Tests on Neoprene at Intermediate and High Strain Rates

2013 ◽  
Vol 631-632 ◽  
pp. 458-462 ◽  
Author(s):  
Peng Duo Zhao ◽  
Yu Wang ◽  
Jian Ye Du ◽  
Lei Zhang ◽  
Zhi Peng Du ◽  
...  
Keyword(s):  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Large Strain ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
High Strain Rates ◽  
Split Hopkinson ◽  
Pressure Bar

The strain rate sensitivity of neoprene is characterized using a modified split Hopkinson pressure bar (SHPB) system at intermediate (50 s-1, 100 s-1) and high (500 s-1, 1000 s-1) strain rates. We used two quartz piezoelectric force transducers that were sandwiched between the specimen and experimental bars respectively to directly measure the weak wave signals. A laser gap gage was employed to monitor the deformation of the sample directly. Three kinds of neoprene rubbers (Shore hardness: SHA60, SHA65, and SHA70) were tested using the modified split Hopkinson pressure bar. Experimental results show that the modified apparatus is effective and reliable for determining the compressive stress-strain responses of neoprene at intermediate and high strain rates.

Mechanical Behavior of Sn1Ag0.5Cu and Sn3Ag0.5Cu Alloys at High Strain Rates

2012 ◽  
Author(s):  
Pradeep Lall ◽  
Sandeep Shantaram ◽  
Jeff Suhling ◽  
David Locker
Keyword(s):  
Strain Rate ◽  
High Speed ◽  
Prolonged Exposure ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Image Correlation ◽  
Constitutive Behavior ◽  
Strain Rates ◽  
High Strain Rates ◽  
Test Technique

Electronics may experience high strain rates when subjected to high g-loads of shock and vibration. Material and damage behavior of electronic materials at high strain rates typical of shock and vibration is scarce. Previously studies have shown that second-level interconnects have a high propensity for failure under shock and vibration loads in fine pitch electronics. Exposure to shock and vibration is common in a variety of consumer environments such as automotive and portable electronics. The low strain-rate properties of commonly used SnAgCu solders, including Sn1Ag0.5Cu and Sn3Ag0.5Cu, have been found to evolve with time after prolonged exposure to high temperatures. High strain rate properties of leadfree solder alloys in the strain-rate range of 1–100 sec−1 are scarce. Previous attempts at characterizing the high strain rates properties have focused on the use of the Split Hopkinson Pressure Bar (SHPB), which enables measurements of strain rates in the neighborhood of 1000 per sec. In this paper, a new test-technique developed by the authors has been presented for measurement of material constitutive behavior. The instrument enables attaining strain rates in the neighborhood of 1 to 100 per sec. Tests are conducted at strain rates 10, 35 and 50 per sec. High speed cameras operating at 75,000 fps have been used in conjunction with digital image correlation for the measurement of full-field strain during the test. Constancy of cross-head velocity has been demonstrated during the test from the unloaded state to the specimen failure. Solder alloy constitutive behavior has been measured for SAC105, SAC305 solders. Non-linear Ramberg-Osgood model has been used to fit the material data. The Ramberg-Osgood model available in Abaqus has been used for tensile test simulation and to correlate with DIC based experimental strain data.

scholarly journals Strain-Rate-Dependent Tensile Response of Ti–5Al–2.5Sn Alloy

Materials ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 659 ◽  
Author(s):  
Bin Zhang ◽  
Jin Wang ◽  
Yang Wang ◽  
Yu Wang ◽  
Ziran Li
Keyword(s):  
Strain Rate ◽  
Strain Hardening ◽  
Uniaxial Tension ◽  
Temperature Rise ◽  
High Strain ◽  
Adiabatic Temperature ◽  
High Rate ◽  
Strain Rates ◽  
High Strain Rates ◽  
Adiabatic Temperature Rise

This study is an experimental investigation on the tensile responses of Ti–5Al–2.5Sn alloy over a wide range of strain rates. Uniaxial tension tests within the rate range of 10−3–101 s−1 are performed using a hydraulic driven MTS810 machine and a moderate strain-rate testing system. The high-rate uniaxial tension and tension recovery tests are conducted using a split-Hopkinson tension bar to obtain the adiabatic and isothermal stress–strain responses of the alloy under dynamic loading conditions. The experimental results show that the value of the initial yield stress increases with the increasing strain rate, while the strain rate sensitivity is greater at high strain rates. The isothermal strain-hardening behavior changes little with the strain rate, and the adiabatic temperature rise is the main reason for the reduction of the strain-hardening rate during high strain-rate tension. The electron backscatter diffraction (EBSD) analysis of the post-deformed samples indicates that there are deformation twins under quasi-static and high-rate tensile loadings. Scanning electron microscope (SEM) micrographs of the fracture surfaces of the post-deformed samples show dimple-like features. The Zerilli–Armstrong model is modified to incorporate the thermal-softening effect of the adiabatic temperature rise at high strain rates and describe the tension responses of Ti–5Al–2.5Sn alloy over strain rates from quasi-static to 1050 s−1.

Sign in / Sign up

Export Citation Format

Share Document