Ultrasonic TOFD Detection by Finite Element Simulation Method

2014 ◽  
Vol 602-605 ◽  
pp. 1594-1597
Author(s):  
Han Xin Chen ◽  
Shi Qi Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Time Of Flight ◽  
Simulation Method ◽  
Industrial Applications ◽  
Detection Methods ◽  
Analysis Model ◽  
Element Analysis ◽  
Time Of Flight Diffraction ◽  
Detection Technology

This paper investigated the ultrasonic mechanism of Time of Flight Diffraction (TOFD) by finite element analysis for the better applications of ultrasonic TOFD (Time of Flight Diffraction) detection technology. The welding steel plate with the artificial defects is used in the finite element analysis model. The experimental A-scan signal with higher noise is filtered by the wavelet transform, which can clearly show defective diffracted wave. The software simulation of ultrasound is used to present the propagation process of ultrasonic signal inside the sample. Simulation results are compared with the experimental results, which shows valid basis for the practical TOFD ultrasonic detection methods in industrial applications.

Simulation of Ultrasonic Detection of Natural Defects in Weld with Finite Element Analysis

2014 ◽  
Vol 602-605 ◽  
pp. 1590-1593
Author(s):  
Han Xin Chen ◽  
Shi Qi Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Analysis Model ◽  
Ultrasonic Detection ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
Detection Technology ◽  
Finite Element Analysis Simulation ◽  
Ultrasonic Time ◽  
The Finite Element Analysis

With the continuous development of the ultrasonic detection technology, ultrasonic time of flight diffraction (TOFD) method has been widely applied. The paper investigated the TOFD technique in the detection of natural defects. TOFD detection experiment is established in Lab. The finite element analysis simulation of A-scan signal and ultrasonic TOFD technique in the detection of the longitudinal arrangement of pores defects within the weld specimen transmission are studied. The feasibility and correctness of the finite element analysis model are verified by comparing the experimental signals with the simulation signals.

Finite Element Analysis Model on Ultrasonic Phased Array Technique for Material Defect Time of Flight Diffraction Detection

2020 ◽  
Vol 12 (5) ◽  
pp. 665-675 ◽  
Author(s):  
Hanxin Chen ◽  
Dongliang Fan ◽  
Jinmin Huang ◽  
Wenjian Huang ◽  
Guangyu Zhang ◽  
...  
Keyword(s):  
Finite Element ◽  
Phased Array ◽  
Time Of Flight ◽  
Element Model ◽  
Analysis Model ◽  
Element Analysis ◽  
Time Of Flight Diffraction ◽  
Array Transducer ◽  
Array Technology ◽  
Ultrasonic Time

In this study, the finite element method (FEM) for phased array technology in ultrasonic time of flight diffraction (TOFD) for the defect detection of two-dimensional (2-D) geometric materials was researched. The phased array technology generated the FEM model for the TOFD signal. We have established the finite element model by the FEM software ANSYS based on the ultrasonic mechanism about the defects and the phased array transducer. A plane strain elements have simulated the reflected signal of the defect. We can compare the error ratio between simulation and experiment by using the theoretical calculation value as the benchmark, and find the feasibility of the FEM detection.

Modeling and experimental verification on directivity of an electret cell array loudspeaker

2012 ◽  
Vol 24 (3) ◽  
pp. 326-333 ◽  
Author(s):  
Yu-Chi Chen ◽  
Wen-Ching Ko ◽  
Han-Lung Chen ◽  
Hsu-Ching Liao ◽  
Wen-Jong Wu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Digital Control System ◽  
Analysis Model ◽  
Cell Array ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
The Finite Element Analysis ◽  
Directivity Characteristics

We propose a model to give us a method to investigate the characteristic three-dimensional directivity in an arbitrarily configured flexible electret-based loudspeaker. In recent years, novel electret loudspeakers have attracted much interest due to their being lightweight, paper thin, and possessing excellent mid- to high-frequency responses. Increasing or decreasing the directivity of an electret loudspeaker makes it excellent for adoption to many applications, especially for directing sound to a particular area or specific audio location. Herein, we detail a novel electret loudspeaker that possesses various directivities and is based on various structures of spacers instead of having to use multichannel amplifiers and a complicated digital control system. In order to study the directivity of an electret loudspeaker based on an array structure which can be adopted for various applications, the horizontal and vertical polar directivity characteristics as a function of frequency were simulated by a finite-element analysis model. To validate the finite-element analysis model, the beam pattern of the electret loudspeaker was measured in an anechoic room. Both the simulated and experimental results are detailed in this article to validate the various assertions related to the directivity of electret cell-based smart speakers.

Finite Element Analysis of Main Stand of Ф140 Pipe Rolling Mill and Split Casting

2013 ◽  
Vol 690-693 ◽  
pp. 2327-2330
Author(s):  
Ming Bo Han ◽  
Li Fei Sun
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Rolling Mill ◽  
Analysis Model ◽  
Element Analysis ◽  
Pipe Rolling ◽  
Full Load ◽  
Finite Element Software ◽  
Theoretical Position ◽  
Technical Requirements

By using finite element software, the paper establishes the main stand analysis model of the Ф140 pipe rolling mill and provides the model analysis of main stand in cases of full load. Verify the design of main stand fully comply with the technical requirements .In this paper, it provides the theoretical position of split casting and welding method using electric slag welding.

Wear analysis of eco-friendly non-asbestos friction-lining material applied in an automotive drum brake: Experimental and finite-element analysis

2021 ◽  
pp. 135065012110167
Author(s):  
Dinesh Shinde ◽  
Mukesh Bulsara ◽  
Jeet Patil
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Surface Wear ◽  
Analysis Model ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
Drum Brake ◽  
Wear Analysis ◽  
Lining Material ◽  
Friction Lining

Brake friction lining material is the critical element of a braking system, since it provides friction resistance to the rotating drum for controlling automobiles. The present study involves wear analysis of newly developed eco-friendly non-asbestos friction lining material for automotive drum brake applications using experimental study, finite-element analysis, and microstructural investigations. Theoretical interpretation of braking force at different automobile speeds was derived using fundamentals. Specimen drum brake liner with eco-friendly material compositions was produced using an industrial hot compression molding process at one of the manufacturer. The surface wear of the liner was measured using an effective and accurate method. Furthermore, a finite-element analysis model was developed considering actual operating conditions and various components of the drum brake system. The model was elaborated for various result outcomes, including Von-Mises stresses and total deformation of components of the drum brake, and further used to estimate the surface wear of the friction lining material in terms of transverse directional deformation. Finally, microstructural analysis of the friction lining material was carried out using scanning electron microscopy and energy dispersive spectroscopy. From the results, it is seen that the developed friction lining material is wear resistant. The finite-element analysis model can be effectively utilized to study the tribological characteristics of friction lining materials.

3D FEA Modeling of Hard Turning

2002 ◽  
Vol 124 (2) ◽  
pp. 189-199 ◽  
Author(s):  
Y. B. Guo ◽  
C. R. Liu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Geometric Model ◽  
Friction Model ◽  
Dominant Factor ◽  
Analysis Model ◽  
Element Analysis ◽  
Plastic Properties ◽  
Fea Model ◽  
Model Predictions

A practical explicit 3D finite element analysis model has been developed and implemented to analyze turning hardened AISI 52100 steels using a PCBN cutting tool. The finite element analysis incorporated the thermo-elastic-plastic properties of the work material in machining. An improved friction model has been proposed to characterize tool-chip interaction with the friction coefficient and shear flow stresses determined by force calibration and material tests, respectively. A geometric model has been established to simulate a 3D turning. FEA Model predictions have reasonable accuracy for chip geometry, forces, residual stresses, and cutting temperatures. FEA model sensitivity analysis indicates that the prediction is consistent using a suitable magnitude of material failure strain for chip separation, the simulation gives reasonable results using the experimentally determined material properties, the proposed friction model is valid and the sticking region on the tool-chip interface is a dominant factor of model predictions.

scholarly journals Finite element analysis of T-joint of mechanical connecting channels

2020 ◽  
Vol 12 (12) ◽  
pp. 168781402097774
Author(s):  
Jiawei Wang ◽  
Fachao Li ◽  
Zibo Chen ◽  
Baishu Li ◽  
Jue Zhu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Rail Transit ◽  
Force Analysis ◽  
Analysis Model ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
Before And After ◽  
Design Software

This paper studies the force and deformation of the connecting channel in Ningbo rail transit construction, which firstly used the mechanical shield method. Steel-concrete composite structural segments are used in the T-joint of connecting channel. The cutting part of the segments are replaced by the concrete and fiberglass instead of reinforced concrete. Basing on a variety of three-dimensional design software and ABAQUS finite element analysis software, a refined finite element analysis model of the special segments is established. By considering the influence of curved joint bolts, the force analysis of the special segments under the structural state before and after construction is performed. According to the analysis and comparison of the deformation of the segments with and without the bolts, it is concluded that the steel-concrete segments can withstand the pressure of the soil before and after the construction. Suggestions for the safety of the design and construction of the segments are put forward.

Development and Validation of Finite Element Analysis Model (FEM) of Craniovertebral Junction

Spine ◽  
2020 ◽  
Vol 45 (16) ◽  
pp. E978-E988
Author(s):  
Deepak Gupta ◽  
Mohd Zubair ◽  
Sanjeev Lalwani ◽  
Shiva Gamanagatti ◽  
Tara Sankar Roy ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Craniovertebral Junction ◽  
Analysis Model ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
Development And Validation
Sign in / Sign up

Export Citation Format

Share Document