Crush Characteristics and Energy Absorption of Thin-Walled Tubes with Through-Hole Crush Initiators

2014 ◽  
Vol 606 ◽  
pp. 181-185 ◽  
Author(s):  
S. Kanna Subramaniyan ◽  
Arun Kumar Kananasan ◽  
Mohd Radzi Mohamed Yunus ◽  
Shahruddin Mahzan ◽  
Mohd Imran Ghazali
Keyword(s):  
Experimental Investigation ◽  
Energy Absorption ◽  
Static Loading ◽  
Absorption Capacity ◽  
Peak Force ◽  
Energy Absorption Capacity ◽  
Steel Tubes ◽  
Thin Walled ◽  
Through Hole ◽  
Initial Peak

An experimental investigation was conducted to compare the crush characteristics and energy absorption capacity of circular and square tubes with located through-hole crush initiator. Circular through-holes were fabricated at three different configurations based on location into steel tubes which had a length of 200 mm. Furthermore, two different side configurations along the tube were considered for introducing the crush initiators. The results found that adding crush initiator onto the tubes were effectively reduced the initial peak force of a thin-walled circular and square tubes under axial quasi-static loading. The peak crush force was reduced within a range 3-10% and 5-16% for circular and square tubes respectively when compared with corresponding tubes without crush initiator. Moreover, the energy absorption capacity of the tubes was independent with the incorporation of through-hole crush initiators. However, the energy absorption of circular and square tubes were slightly decreases when compared with the tubes fabricated four sided crush initiation and tubes without crush initiator. Overall, the effect of location and number of crush initiation proved significantly influences the initial peak forces while maintain the energy absorbed.

The Energy Absorption Characteristics of Square Mild Steel Tubes With Multiple Induced Circular Hole Discontinuities—Part I: Experiments

2009 ◽  
Vol 76 (4) ◽  
Author(s):  
S. B. Bodlani ◽  
S. Chung Kim Yuen ◽  
G. N. Nurick
Keyword(s):  
Mild Steel ◽  
Energy Absorption ◽  
Circular Hole ◽  
Progressive Collapse ◽  
Experimental Tests ◽  
Absorption Capacity ◽  
Peak Force ◽  
Steel Tubes ◽  
Initial Peak ◽  
Absorption Characteristics

This two-part article reports the results of experimental and numerical works conducted on the energy absorption characteristics of thin-walled square tubes with multiple circular hole discontinuities. Part I presents the experimental tests in which dynamic and quasistatic axial crushings are performed. The mild steel tubes are 350 mm in length, 50 mm wide, and 1.5 mm thick. Circular hole discontinuities, 17 mm in diameter, are laterally drilled on two or all four opposing walls of the tube to form opposing hole pairs. The total number of holes varies from 2 to 10. The results indicate that the introduction of holes decreases the initial peak force but an increase in the number of holes beyond 2 holes per side does not further significantly decrease the initial peak force. The findings show that strategic positioning of holes triggers progressive collapse hence improving energy absorption. The results also indicate that the presence of holes may at times disrupt the formation of lobes thus compromising the energy absorption capacity of the tube. In Part II, the finite element package ABAQUS/EXPLICIT version 6.4–6 is used to model the dynamic axial crushing of the tubes and to investigate the action of the holes during dynamic loading at an impact velocity of 8 m/s.

Response of Filled Thin-Walled Square Tubes to Axial Impact Load

2014 ◽  
Vol 566 ◽  
pp. 586-592
Author(s):  
Steeve Chung Kim Yuen ◽  
Gerald Nurick ◽  
Sylvester Piu ◽  
Gadija Ebrahim
Keyword(s):  
Energy Absorption ◽  
High Speed ◽  
Impact Load ◽  
Absorption Capacity ◽  
Tubular Structures ◽  
Energy Absorption Capacity ◽  
Axial Impact ◽  
Foam Filled ◽  
Thin Walled ◽  
Initial Peak

This paper presents the results of an investigation into the response of thin-walled square (60x60 mm and 76x76 mm) tubes made from mild steel filled with four different fillers; aluminium foam (Cymat 7%), two types of aluminium honeycomb and polyurethane foam to quasi-static and dynamic axial impact load. The energy absorption characteristics of the foam-filled tubes are compared to that of a hollow tube, through efficiency calculations. The tubular structures are subjected to axial impact load generated by drop masses of 320 kg and 390 kg released from a height ranging between 2.1 m to 4.1 m. Footage from a high speed camera is used to determine the average crush forces exerted by each specimen. The results show that the fillers have insignificant effects on the initial peak forces based on the quasi-static results but increase the overall mean crushed force. The findings also indicate that the fillers affect at times the size of the lobe formed thus compromising the energy absorption capacity of the tube.

Numerical Investigation of Cross-Section on Aluminum A6063 Thin-Walled Structures under Low-Velocity Impact Loading

2014 ◽  
Vol 1019 ◽  
pp. 96-102
Author(s):  
Ali Taherkhani ◽  
Ali Alavi Nia
Keyword(s):  
Energy Absorption ◽  
Cross Section ◽  
Cross Sections ◽  
Peak Load ◽  
Circular Cross Section ◽  
Absorption Capacity ◽  
Energy Absorption Capacity ◽  
Thin Walled Structures ◽  
Thin Walled ◽  
Crush Strength

In this study, the energy absorption capacity and crush strength of cylindrical thin-walled structures is investigated using nonlinear Finite Elements code LS-DYNA. For the thin-walled structure, Aluminum A6063 is used and its behaviour is modeled using power-law equation. In order to better investigate the performance of tubes, the simulation was also carried out on structures with other types of cross-sections such as triangle, square, rectangle, and hexagonal, and their results, namely, energy absorption, crush strength, peak load, and the displacement at the end of tubes was compared to each other. It was seen that the circular cross-section has the highest energy absorption capacity and crush strength, while they are the lowest for the triangular cross-section. It was concluded that increasing the number of sides increases the energy absorption capacity and the crush strength. On the other hand, by comparing the results between the square and rectangular cross-sections, it can be found out that eliminating the symmetry of the cross-section decreases the energy absorption capacity and the crush strength. The crush behaviour of the structure was also studied by changing the mass and the velocity of the striker, simultaneously while its total kinetic energy is kept constant. It was seen that the energy absorption of the structure is more sensitive to the striker velocity than its mass.

Excellent energy absorption capacity of nanostructured Cu–Zn thin-walled tube

2014 ◽  
Vol 599 ◽  
pp. 141-144 ◽  
Author(s):  
M. Afrasiab ◽  
G. Faraji ◽  
V. Tavakkoli ◽  
M.M. Mashhadi ◽  
A.R. Bushroa
Keyword(s):  
Energy Absorption ◽  
Absorption Capacity ◽  
Energy Absorption Capacity ◽  
Thin Walled Tube ◽  
Thin Walled

scholarly journals Energy Absorption Capability of Thin-Walled Prismatic Aluminum Tubes with Spherical Indentations

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4304
Author(s):  
Miroslaw Ferdynus ◽  
Patryk Rozylo ◽  
Michal Rogala
Keyword(s):  
Aluminum Alloy ◽  
Energy Absorption ◽  
Numerical Models ◽  
Energy System ◽  
High Energy ◽  
Absorption Capacity ◽  
Energy Absorption Capacity ◽  
Numerical Tests ◽  
Thin Walled ◽  
Crushing Behavior

The paper presents the results of numerical tests of impact and energy absorption capacity of thin-walled columns, subjected to axial impact loading, made of aluminum alloy, and having a square cross-section and spherical indentations on their lateral surfaces. The numerical models were validated using an experiment that was conducted on the Instron CEAST 9350 High Energy System drop hammer. Material properties of the applied aluminum alloy were determined on the basis of a static tension test. The crushing behavior of the columns and some crashworthiness indicators were investigated. On the basis of the results of the conducted analyses, conclusions were drawn about the most beneficial design/constructional variants in terms of achieved crashworthiness parameters.

Energy absorption capacity for thin-walled AM60 castings using a shear-bolt principle

2007 ◽  
Vol 85 (1-2) ◽  
pp. 89-101 ◽  
Author(s):  
Cato Dørum ◽  
Odd Sture Hopperstad ◽  
Odd-Geir Lademo ◽  
Magnus Langseth
Keyword(s):  
Energy Absorption ◽  
Absorption Capacity ◽  
Energy Absorption Capacity ◽  
Thin Walled

Impact Response of Circular Tube with Concentric Plunger

2013 ◽  
Vol 275-277 ◽  
pp. 792-798
Author(s):  
Amir Radzi Ab Ghani ◽  
Hafizi Lukman ◽  
Hafizan Hashim
Keyword(s):  
Energy Absorption ◽  
Circular Tube ◽  
High Energy ◽  
Absorption Capacity ◽  
Peak Force ◽  
Impact Response ◽  
Impact Performance ◽  
High Energy Absorption ◽  
The Impact ◽  
Initial Peak

Thin-walled tubes are generally used as impact energy absorber in various application due to their ease of fabrication and installation, high energy absorption capacity and long stroke. However, the main drawback of plain tube is the high initial peak force. A concentric plunger in the form of tapered block is proposed to overcome this shortcoming while at the same time, improving the impact performance. Static and dynamic axial crushing were performed to determine the initial peak force (IPF), crush force efficiency (CFE) and specific energy absorption (SEA) for the concentric plunger with various taper angles. It was found that the concentric plunger affected the tube impact response. Comparison with plain circular tube was carried out and it was found that the concentric plunger improved the impact response of the tube especially in term of initial peak force.

Experimental Investigation of Energy Absorption of ‎Partially Wrapped Thin-Walled ‎Aluminium-Glass/Epoxy Tube Subjected to Quasi-Static Loading

2017 ◽  
Vol 904 ◽  
pp. 61-67
Author(s):  
Tahir Abbas ◽  
Hamdan H. Ya ◽  
Mohamad Zaki Abdullah
Keyword(s):  
Experimental Investigation ◽  
Energy Absorption ◽  
Fiber Orientation ◽  
Static Loading ◽  
Failure Modes ◽  
Testing Machine ◽  
Filament Winding ◽  
Universal Testing ◽  
Thin Walled ◽  
Filament Winding Process

This paper describes the failure modes and energy absorption capability of partially wrapped aluminium-glass/epoxy tubes, subjected to quasi-static loading. ‎These tubes are used in aircraft and automobiles applications. Aluminium tubes were partially wrapped with 4, 6 and 8 glass/epoxy layers, using filament winding process. The 90◦ fiber orientation was used for glass/epoxy layers. Quasi-static loading of partially wrapped tubes was carried out at 5mm/min speed, using the universal ‎testing machine. The experimental results revealed that partially wrapped aluminium tubes are 42.54%, 47.77% and 28.91% more ‎efficient in energy absorption as compared to the simple aluminium tubes. Furthermore, the effect of glass/epoxy layers on ‎failure modes has also been described.

scholarly journals Design Optimization of Crashworthiness in Square Tube as Thin Walled Structure With Variations of Crush Initiator: Stripe-Parallelogram-Trigon

2018 ◽  
Vol 4 (1) ◽  
Author(s):  
Felix Dionisius ◽  
Jos Istiyanto ◽  
Tito Endramawan ◽  
Andri Andri
Keyword(s):  
Energy Absorption ◽  
Specific Energy ◽  
Static Loading ◽  
Peak Force ◽  
Multi Criteria Decision Making ◽  
Specific Energy Absorption ◽  
Vehicle Structure ◽  
Experiment Method ◽  
Thin Walled ◽  
Simple Additive Weighting

Crashworthiness is an ability of a vehicle structure in order to reduce injury when occurred in collision. Crashworthiness criteria are peak force (Fmax), specific energy absorption (SEA), and crush force efficiency (CFE). The part of structure of vehicle in crashworthiness is front rail which is generally tube as thin walled structure. The aim was to know the best design in thin walled square tube as specimen by variance of crush initiator which arranged holes 3 mm of diameter in shaping stripe with 4 holes, then added graded holes in parallelogram to trigon. This research used compression experiment method under quasi static loading with 30 mm/minute of actuator velocity. Optimum design was done by using Multi Criteria Decision Making (MCDM) with Simple Additive Weighting (SAW) modelling. This research presents that specimen with trigon of crush initiator is the best design with 0.98 of decision score in which crashworthiness criteria for peak force, specific energy absorption and crush force efficiency are 19193.81 N; 5100.93 J/kg; and 46.44%.

Sign in / Sign up

Export Citation Format

Share Document