Numerical Simulation for the Multi-Point Incremental Forming Process

2015 ◽  
Vol 775 ◽  
pp. 219-223
Author(s):  
Wan Mian Yang ◽  
Yuan Xin Luo ◽  
Zhi Fang Liu ◽  
Ru Xu Du
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Incremental Forming ◽  
Element Model ◽  
Sheet Metals ◽  
Forming Force ◽  
Forming Process ◽  
Thickness Change

Multi-point forming process has been developed to shape the sheet metal with bidirectional curvature. However, the forming force usually climbs too high so that the dimension of the forming machine should be designed to meet it. To solve this problem, the multi-point incremental forming (MPIF) process was proposed in this paper. First, the principle of this new forming process was introduced. Then, the experimental device was designed. Next, the MPIF process was simulated by a finite element model. The forming effects including displacements, thickness, and curvatures were visualized and discussed in detail. It was found that there is no obvious thickness change during the forming process. The advantage of this forming process is that the shape of the sheet metals adaptable and controllable with small forming force.

Sheet Metals Forming Die Design Using Finite Element Analysis and the Taguchi Method

2014 ◽  
Vol 621 ◽  
pp. 195-201
Author(s):  
Surangsee Dechjarern ◽  
Maitri Kamonrattanapisut
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Friction Coefficient ◽  
Taguchi Method ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Element Model ◽  
Die Design ◽  
Forming Process ◽  
Element Analysis

Sheet metal deep-draw die is primarily constructed with draw bead, which is then modified based on trial and error to obtain a successful forming without splitting. This work aims at a robust design of forming die using numerical analysis and the Taguchi method. A three dimensional elastoplastic finite element model of a sheet metal forming process of SPCEN steel has been successfully developed using the material flow stress obtained from the modified Erichsen cup test. The model was validated with the actual forming experiment and the results agreed well. The influence of draw bead parameters on splitting and thinning distributions were examined using the Taguchi method. Four parameters, namely the friction coefficient, draw bead height, radius and shoulder radius were investigated. The Taguchi main effect analysis and ANOVA results show that the height and shoulder radius of the draw bead are the most important factor influencing the thinning distribution. Applying the Taguchi method and using the minimum thinning percentage as the design criteria, the optimum die design was identified as height, radius, shoulder radius and the friction coefficient of 4, 8, 8 mm and 0.125 respectively. The verified finite element model using the optimum die design was conducted. The predicted Taguchi response was within 5.9% from finite element analysis prediction. The improvement in the reduction of thinning percentage was 22.35%.

Single-point incremental forming of sheet metals: Experimental study and numerical simulation

2016 ◽  
Vol 231 (2) ◽  
pp. 301-312 ◽  
Author(s):  
Matteo Benedetti ◽  
Vigilio Fontanari ◽  
Bernardo Monelli ◽  
Marco Tassan
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Incremental Forming ◽  
Single Point ◽  
Integration Scheme ◽  
Al Alloy ◽  
Single Point Incremental Forming ◽  
Sheet Metals ◽  
Forming Process ◽  
Starting Point

In this article, the single-point incremental forming of sheet metals made of micro-alloyed steel and Al alloy is investigated by combining the results of numerical simulation and experimental characterization, performed during the process, as well as on the final product. A finite element model was developed to perform the process simulation, based on an explicit dynamic time integration scheme. The finite element outcomes were validated by comparison with experimental results. In particular, forming forces during the process, as well as the final shape and strain distribution on the finished component, were measured. The obtained results showed the capability of the finite element modelling to predict the material deformation process. This can be considered as a starting point for the reliable definition of the single-point incremental forming process parameters, thus avoiding expensive trial-and-error approaches, based on extensive experimental campaigns, with beneficial effects on production time.

Comparison between an Advanced Numerical Simulation of Sheet Incremental Forming Using Adaptive Remeshing and Experimental Results

2013 ◽  
Vol 554-557 ◽  
pp. 1375-1381 ◽  
Author(s):  
Laurence Giraud-Moreau ◽  
Abel Cherouat ◽  
Jie Zhang ◽  
Houman Borouchaki
Keyword(s):  
Numerical Simulation ◽  
Numerical Model ◽  
Sheet Metal ◽  
Metal Forming ◽  
Tool Path ◽  
Incremental Forming ◽  
Computation Time ◽  
Experimental Results ◽  
Forming Process ◽  
Adaptive Remeshing

Recently, new sheet metal forming technique, incremental forming has been introduced. It is based on using a single spherical tool, which is moved along CNC controlled tool path. During the incremental forming process, the sheet blank is fixed in sheet holder. The tool follows a certain tool path and progressively deforms the sheet. Nowadays, numerical simulations of metal forming are widely used by industry to predict the geometry of the part, stresses and strain during the forming process. Because incremental forming is a dieless process, it is perfectly suited for prototyping and small volume production [1, 2]. On the other hand, this process is very slow and therefore it can only be used when a slow series production is required. As the sheet incremental forming process is an emerging process which has a high industrial interest, scientific efforts are required in order to optimize the process and to increase the knowledge of this process through experimental studies and the development of accurate simulation models. In this paper, a comparison between numerical simulation and experimental results is realized in order to assess the suitability of the numerical model. The experimental investigation is realized using a three-axis CNC milling machine. The forming tool consists in a cylindrical rotating punch with a hemispherical head. A subroutine has been developed to describe the tool path from CAM procedure. A numerical model has been developed to simulate the sheet incremental forming process. The finite element code Abaqus explicit has been used. The simulation of the incremental forming process stays a complex task and the computation time is often prohibitive for many reasons. During this simulation, the blank is deformed by a sequence of small increments that requires many numerical increments to be performed. Moreover, the size of the tool diameter is generally very small compared to the size of the metal sheet and thus the contact zone between the tool and the sheet is limited. As the tool deforms almost every part of the sheet, small elements are required everywhere in the sheet resulting in a very high computation time. In this paper, an adaptive remeshing method has been used to simulate the incremental forming process. This strategy, based on adaptive refinement and coarsening procedures avoids having an initially fine mesh, resulting in an enormous computing time. Experiments have been carried out using aluminum alloy sheets. The final geometrical shape and the thickness profile have been measured and compared with the numerical results. These measurements have allowed validating the proposed numerical model. References [1] M. Yamashita, M. Grotoh, S.-Y. Atsumi, Numerical simulation of incremental forming of sheet metal, J. Processing Technology, No. 199 (2008), p. 163 172. [2] C. Henrard, A.M. Hbraken, A. Szekeres, J.R. Duflou, S. He, P. Van Houtte, Comparison of FEM Simulations for the Incremental Forming Process, Advanced Materials Research, 6-8 (2005), p. 533-542.

scholarly journals The Effect of Swinging Ball Heads with Different Arrangements in Multi-Point Stretch-Forming Process

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 337 ◽  
Author(s):  
Jian Xing ◽  
Yan-yan Cheng ◽  
Zhuo Yi
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Sheet Metal ◽  
Strain Distribution ◽  
Finite Element Models ◽  
Stretch Forming ◽  
Forming Process ◽  
Forming Quality ◽  
Staggered Arrangement ◽  
Simulation Results

To improve the effect of multi-point stretch forming of sheet metal, it is proposed in this paper to replace a fixed ball head with a swinging ball head. According to the multi-point dies with different arrangements, this research establishes finite element models of the following stretch forming, i.e., fixed ball heads with conventional arrangement, swinging ball heads with conventional arrangement, swinging ball heads with declining staggered arrangement, and swinging ball heads with parallel staggered arrangement, and then numerical simulation is performed. The simulation results show that by replacing a fixed ball head with a swinging ball head, the surface indentation of the part formed was effectively suppressed, the stress and tension strain distribution of the part formed was improved, and the forming quality was improved; the thickness of the elastic pad was reduced, the springback was reduced and the forming accuracy was improved; and when the ball head was applied to a multi-point die with staggered arrangement, a better forming result was achieved, where the best forming result was achieved in combining the swinging ball heads with the multi-point die with a parallel staggered arrangement. Forming experiments were carried out, and the experimental results were consistent with the trend of numerical simulation results, which verified the correctness of the numerical simulation.

Numerical Simulation of Steel Grid Structure under High Temperature

2013 ◽  
Vol 838-841 ◽  
pp. 458-461
Author(s):  
Jing Cui ◽  
Ling Feng Yin ◽  
Xiao Ming Guo ◽  
Gan Tang ◽  
Tian Jiao Jin
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
High Temperature ◽  
Finite Element Model ◽  
Numerical Method ◽  
Nonlinear Interaction ◽  
Element Model ◽  
Fire Tests ◽  
Grid Structure ◽  
Test Models

Based on the fire tests of WILLIAMS double-poles structure, considering the dual nonlinear interaction of material and geometric, established one complete finite element model of grid structure. For the performance that the physical and mechanics properties of steel will degrade while the temperature arising, simulate the test models with ANSYS, get a better numerical results, proof the numerical method is feasible.

FEM Simulation of Anisotropic Parameters Influencing the Earing in Sheet Metal Deep Drawing Process

2011 ◽  
Vol 88-89 ◽  
pp. 638-641 ◽  
Author(s):  
Lei Chen
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Deep Drawing ◽  
Fem Simulation ◽  
Element Model ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Material Characteristics

Earing is often undesirable in the production of deep drawn containers because it results in a nonuniform cup height. A finite element model for earring analysis is developed considering only the flange area of the sheet. It was found that the draw-in depth of the flange increases with the increase of the r value, and it remains invariable when r value is larger than 2. With the increase of the r value, the max thickness decreases and the min thickness increases. If △r>0, four earings are formed. If △r =0, the material characteristics in all the planar directions are same. The flange uniformly flows into the die cavity, no earing is formed. If △r<0, four earings are formed. The earing distribution is dominated by r0, r45 and r90. Both r and △r have much effect on the earing distribution.

A Finite Element Model of the Squeeze Forming Process

Cast Metals ◽  
1991 ◽  
Vol 4 (2) ◽  
pp. 89-97 ◽  
Author(s):  
M. R. Tadayon ◽  
R. W. Lewis ◽  
D.T. Gethin
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Forming Process

FE Simulation of Vacuum Hot Bulge Forming Process of BT20 Ti-Alloy Cylindrical Workpiece

2008 ◽  
Vol 392-394 ◽  
pp. 366-369
Author(s):  
Ming Wei Wang ◽  
Li Wen Zhang
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Heating Temperature ◽  
Radiation Heat Transfer ◽  
Element Model ◽  
Ti Alloy ◽  
Forming Process ◽  
Relaxation Theory ◽  
Finite Element Software ◽  
Cylindrical Workpiece

The vacuum hot bulge forming has been used in aerospace industry to manufacture cylindrical workpiece with improved mechanical properties and reduced fabrication cost. Vacuum hot bulge forming is based on the material soften and the stress relaxation theory. Different from other metal forming techniques, deformation of the workpiece takes place well below yield point and the amount of plastic deformation is directly relaxed to heating temperature and holding time. In this paper, a two-dimension thermo-mechanical coupled finite element model was developed. In this model, nonlinear radiation heat transfer and thermal physical properties of material depending on temperature were considered. This paper carried out numerical simulation of vacuum hot bulge forming of BT20 Ti-alloy cylindrical workpiece by using finite element software MSC.Marc. The temperature field, deformation field and stress field of hot bulge forming of BT20 Ti-alloy cylindrical workpiece were calculated. Numerical simulation results were accorded with experimental ones, which provided for the practice production as theory bases.

Sign in / Sign up

Export Citation Format

Share Document