Microtwins of Transformation and their Effect on Excess Dislocation Density of FCC Deformed Material

2014 ◽  
Vol 1013 ◽  
pp. 72-76 ◽  
Author(s):  
Svetlana Kiseleva ◽  
Natal'ya Popova ◽  
Nina Koneva ◽  
Eduard Kozlov
Keyword(s):  
Plastic Deformation ◽  
Dislocation Density ◽  
Austenitic Steel ◽  
Internal Stresses ◽  
Plastic Deformations ◽  
Density Of Dislocations ◽  
Elastic And Plastic Deformations ◽  
Excess Density

The excess density of dislocations and internal stresses in local places of all polycrystal grain are determined. In work the methods of bending extinction contours observed by TEM is used to determine internal stresses of the deformed material. Thus depending on the deformation nature in each case components of elastic and plastic deformations or only plastic deformation was considered. The paper discusses the results of distribution of excess dislocation density and internal stresses within the grains of the austenitic steel deformed by tension (ε = 25%).

Numerical Analysis for Influence of Plastic and Elastic Deformation of Rough Surfaces on PEHL for Line Contacts

Tribology ◽  
2005 ◽  
Author(s):  
R. J. Niu ◽  
P. Huang
Keyword(s):  
Plastic Deformation ◽  
Film Thickness ◽  
Hydrodynamic Lubrication ◽  
Paper Analysis ◽  
Line Contact ◽  
Plastic Deformations ◽  
Rolling Contacts ◽  
Line Contacts ◽  
Elastic And Plastic Deformations ◽  
Strain Relationship

In the present paper, analysis of elasto-plasto-hydrodynamic lubrication (PEHL) in the line contact is carried out to investigate the effect of heavily loaded roll-over on the change in profile of indents. The pressure and film thickness profiles are obtained to solve the Reynolds and film thickness equations simultaneously. And, both the elastic and plastic deformations of the contact, featured with an indent, have been considered. A multi-grid numerical algorithm used in EHL of line contacts is modified and then used for the oil lubricated rolling contacts. In the program, stress and plastic deformation of the indent profile are calculated with the hardening plastic stress-strain relationship according to the theories of plasticity when pressure excesses the yield stress. The results, with and without considering plastic deformation, are compared to show the different influences on the pressure and film thickness. Analysis shows that since the plastic deformation will change the surface roughness, it will significantly change the pressure but film thickness.

Effect of elastic and plastic deformations on tribological behavior of graphene-reinforced Ni3Al matrix composites

2017 ◽  
Vol 232 (10) ◽  
pp. 1261-1272 ◽  
Author(s):  
Yuchun Huang ◽  
Xiaoliang Shi ◽  
Kang Yang ◽  
Jialiang Zou ◽  
Qiao Shen ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Tribological Properties ◽  
Tribological Behavior ◽  
Tribological Performance ◽  
Plastic Deformations ◽  
Wear Resistant ◽  
Elastic And Plastic Deformations ◽  
Resistant Layer ◽  
Al Matrix ◽  
Self Lubricating Composites

The elastic and plastic deformations have significant effect on the tribological properties of the graphene-reinforced Ni3Al matrix self-lubricating composites. The primary purpose of this study is to investigate the tribological behavior and wear mechanisms of graphene-reinforced Ni3Al matrix self-lubricating composites by researching the effects of different loads and the corresponding friction heat on the elastic or plastic deformation. The dry sliding tribology tests of graphene-reinforced Ni3Al matrix self-lubricating composites are carried out at the loads of 7, 10, 13, and 16N, respectively. The elastic or plastic deformation is judged by comparing the yield stress with the contact stress analyzed by the numerical simulation method. It is found that graphene-reinforced Ni3Al matrix self-lubricating composites exhibit good tribological properties at 13 N due to the elastic deformation, leading to the formation of relatively stable wear resistant layer. Graphene-reinforced Ni3Al matrix self-lubricating composites show poor tribological performance at 16 N for the plastic deformation, resulting in the destruction of the wear resistant layer and the generation of surface cracks and material spalling. From the mechanical mechanism of wear, the plastic deformation and thermal stress are the important factors to lead to the material spalling. The results could be used to guide the selection of suitable working conditions for having good tribological performance of low wear and long service life.

scholarly journals Análise de um pavimento reforçado com geossintético a partir de resultados de ensaio em equipamento de grandes dimensões

TRANSPORTES ◽  
2011 ◽  
Vol 19 (3) ◽  
pp. 28
Author(s):  
Francis Massashi Kakuda ◽  
Alexandre Benetti Parreira ◽  
Glauco Tulio Pessa Fabbri
Keyword(s):  
Plastic Deformation ◽  
Numerical Modeling ◽  
Laboratory Tests ◽  
Resilient Modulus ◽  
Base Layer ◽  
Plastic Deformations ◽  
Elastic And Plastic Deformations ◽  
Back Calculation ◽  
Pavement Reinforcement ◽  
Elastic And Plastic Deformation

<p><strong>Resumo</strong>: O artigo analisa o beneficio do uso de uma geogrelha como reforço da camada de base de um pavimento. Seções do pavimento e subleito com dimensões próximas às reais submetidas a carregamentos cíclicos foram ensaiadas numa caixa metálica quadrada com lado de 1,5 m e altura de 1,2 m. Concluiu-se que a utilização da geogrelha proporciona a redução de deformações elásticas e permanentes, e que a eficiência do reforço posicionado na interface com o subleito é maior que a do reforço posicionado no horizonte médio da base. Foram ainda determinados os módulos de resiliência da base e do subleito a partir da retroanálise das bacias de deflexões obtidas nos ensaios. Finalmente, a análise numérica de um pavimento hipotético mostrou que a geogrelha pode proporcionar uma extensão expressiva na vida de fadiga do revestimento asfáltico.</p><p><strong>Palavras-chave</strong>: pavimentos reforçados com geosintéticos, geogrelha, ensaios de laboratório em verdadeira grandeza, deformações elásticas e plásticas sob carregamento cíclicos.</p><p><strong>Abstract</strong>: The article analyzes the benefits of the application of a geogrid as base layer pavement reinforcement. Cyclic loaded fullscale sections of pavement and subgrade were tested in a square metallic box with 1.5 m width and 1.2 m height. It was concluded that the geogrid reduces the elastic and plastic deformations and also that positioning the reinforcing at subgrade interface is more efficient than at base medium horizon. The base and subgrade resilient modulus were obtained by back calculation using the deflection basin results from the tests. Finally, a numerical modeling of a hypothetic pavement showed that the geogrid may conduct to an expressive increase of the bituminous surface life.</p><p><strong>Keywords</strong>: geosynthetic reforced pavement, geogrid, full-scale laboratory tests, elastic and plastic deformation under cyclic loadings.</p>

A Biomimetic Approach to the Design of the Composite Bottle Cap and Deformation Analyses

2009 ◽  
Vol 2 ◽  
pp. 59-72
Author(s):  
Li Zhi Gu ◽  
Z. Zhang
Keyword(s):  
Plastic Deformation ◽  
Structural Feature ◽  
Thin Wall ◽  
Functional Requirements ◽  
Plastic Deformations ◽  
Pressing Force ◽  
Maximum Value ◽  
Elastic And Plastic Deformations ◽  
Biomimetic Approach

On the combination analog of the mussel ripple and leaf embrace, designed a new composite bottle cap consisting of the outer body, the inner lining washer, and the resin embrace, for multi-function, especially for better seal and ready open. According to the structural feature and the functional requirements of the cap, two fundamental components, the lining washer and the outer body, were abstracted into a plate and a cylinder with thin wall, respectively. Under the pressing force the elastic and plastic deformations of both were studied with Tresca’s yielding rule and the limitation of the plastic deformation was presented when the two components were assembled into a unit. For the production of this kind of bottle cap, the maximum value of the allowance press and the maximum pressing velocity were also provided.

Capillary forces drive buckling, plastic deformation, and break-up of 3D printed beams

Soft Matter ◽  
2021 ◽  
Vol 17 (14) ◽  
pp. 3886-3894
Author(s):  
Christopher S. O’Bryan ◽  
Alexandria Brady-Miné ◽  
Crystal J. Tessmann ◽  
Amanda M. Spotz ◽  
Thomas E. Angelini
Keyword(s):  
Plastic Deformation ◽  
Soft Materials ◽  
Capillary Forces ◽  
Plastic Deformations ◽  
Elastic And Plastic Deformations ◽  
3D Printed ◽  
Break Up

Capillary forces acting at the interfaces of soft materials lead to elastic and plastic deformations and instabilities that result in buckling, coiling, and break-up of 3D printed beams.

Investigation of shock-wave deformation history from recovered structure

1986 ◽  
Vol 44 ◽  
pp. 434-435
Author(s):  
M.A. Mogilevsky ◽  
L.S. Bushnev
Keyword(s):  
Shock Wave ◽  
Plastic Deformation ◽  
Dislocation Density ◽  
Shock Waves ◽  
Shock Front ◽  
Single Crystals ◽  
Residual Deformation ◽  
Deformation Structure ◽  
Deformation History ◽  
Deformation Velocity

Single crystals of Al were loaded by 15 to 40 GPa shock waves at 77 K with a pulse duration of 1.0 to 0.5 μs and a residual deformation of ∼1%. The analysis of deformation structure peculiarities allows the deformation history to be re-established.After a 20 to 40 GPa loading the dislocation density in the recovered samples was about 1010 cm-2. By measuring the thickness of the 40 GPa shock front in Al, a plastic deformation velocity of 1.07 x 108 s-1 is obtained, from where the moving dislocation density at the front is 7 x 1010 cm-2. A very small part of dislocations moves during the whole time of compression, i.e. a total dislocation density at the front must be in excess of this value by one or two orders. Consequently, due to extremely high stresses, at the front there exists a very unstable structure which is rearranged later with a noticeable decrease in dislocation density.

scholarly journals Structural Transformations and Mechanical Properties of Metastable Austenitic Steel under High Temperature Thermomechanical Treatment

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 645
Author(s):  
Igor Litovchenko ◽  
Sergey Akkuzin ◽  
Nadezhda Polekhina ◽  
Kseniya Almaeva ◽  
Evgeny Moskvichev
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Temperature ◽  
Austenitic Steel ◽  
Structural Transformations ◽  
Initial State ◽  
Twin Boundaries ◽  
Metastable Austenitic Steel ◽  
Average Grain Size ◽  
Heating Up

The effect of high-temperature thermomechanical treatment on the structural transformations and mechanical properties of metastable austenitic steel of the AISI 321 type is investigated. The features of the grain and defect microstructure of steel were studied by scanning electron microscopy with electron back-scatter diffraction (SEM EBSD) and transmission electron microscopy (TEM). It is shown that in the initial state after solution treatment the average grain size is 18 μm. A high (≈50%) fraction of twin boundaries (annealing twins) was found. In the course of hot (with heating up to 1100 °C) plastic deformation by rolling to moderate strain (e = 1.6, where e is true strain) the grain structure undergoes fragmentation, which gives rise to grain refining (the average grain size is 8 μm). Partial recovery and recrystallization also occur. The fraction of low-angle misorientation boundaries increases up to ≈46%, and that of twin boundaries decreases to ≈25%, compared to the initial state. The yield strength after this treatment reaches up to 477 MPa with elongation-to-failure of 26%. The combination of plastic deformation with heating up to 1100 °C (e = 0.8) and subsequent deformation with heating up to 600 °C (e = 0.7) reduces the average grain size to 1.4 μm and forms submicrocrystalline fragments. The fraction of low-angle misorientation boundaries is ≈60%, and that of twin boundaries is ≈3%. The structural states formed after this treatment provide an increase in the strength properties of steel (yield strength reaches up to 677 MPa) with ductility values of 12%. The mechanisms of plastic deformation and strengthening of metastable austenitic steel under the above high-temperature thermomechanical treatments are discussed.

Buckling of Columns in the Presence of Creep

1956 ◽  
Vol 7 (2) ◽  
pp. 125-134 ◽  
Author(s):  
Sharad A. Patel
Keyword(s):  
Critical Time ◽  
Secondary Creep ◽  
Plastic Deformations ◽  
Creep Buckling ◽  
Elastic And Plastic Deformations

SummaryThis paper is concerned with the solution of the creep buckling of columns. Instantaneous elastic and plastic deformations, as well as the transient and secondary creep, are considered. Formulae for the critical time at which a column fails are presented for integral values of the exponents appearing in the creep law.

Sign in / Sign up

Export Citation Format

Share Document