Three-Dimensional Numerical Simulation of Mixed Convective Heat Transfer in a Horizontal Rectangular Duct Utilizing Nanofluids

2014 ◽  
Vol 1016 ◽  
pp. 738-742
Author(s):  
Nur Irmawati Om ◽  
H.A. Mohammed
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Volume Fraction ◽  
Three Dimensional ◽  
Rectangular Duct ◽  
Thermal Fields ◽  
Nanoparticles Volume Fraction

Predictions are reported for three-dimensional laminar mixed convective heat transfer using nanofluids in a horizontal rectangular duct. Five different types of nanoparticle, Ag, Al2O3, Au, Cu and SiO2 with nanoparticles volume fractions range of 2% to 10% are investigated. In this study, the effects of nanofluids type, nanoparticles volume fraction of nanofluids and the effect of aspect ratio on the thermal fields were examined. Results reveal that the addition of nanoparticles to the base fluid and their volume fraction tend to increase the Nusselt number along the horizontal rectangular duct (i.e., increases the rate of heat transfer). It was also found that the Nusselt number increases as the aspect ratio decreases.

Natural convective heat transfer in a hemispherical cavity filled with ZnO–H2O nanofluid saturated porous medium

2018 ◽  
Vol 29 (10) ◽  
pp. 1850097 ◽  
Author(s):  
Abderrahmane Baïri ◽  
Najib Laraqi
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Volume Fraction ◽  
Saturated Porous Medium ◽  
Physical Parameters ◽  
Numerical Work

This three-dimensional (3D) numerical work based on the volume control method quantifies the convective heat transfer occurring in a hemispherical cavity filled with a ZnO–H2O nanofluid saturated porous medium. Its main objective is to improve the cooling of an electronic component contained in this enclosure. The volume fraction of the considered monophasic nanofluid varies between 0% (pure water) and 10%, while the cupola is maintained isothermal at cold temperature. During operation, the active device generates a heat flux leading to high Rayleigh number reaching [Formula: see text] and may be inclined with respect to the horizontal plane at an angle ranging from 0[Formula: see text] to 180[Formula: see text] (horizontal position with cupola facing upwards and downwards, respectively) by steps of 15[Formula: see text]. The natural convective heat transfer represented by the average Nusselt number has been quantified for many configurations obtained by combining the tilt angle, the Rayleigh number, the nanofluid volume fraction and the ratio between the thermal conductivity of the porous medium’s solid matrix and that of the base fluid. This ratio has a significant influence on the free convective heat transfer and ranges from 0 (without porous media) to 70 in this work. The influence of the four physical parameters is analyzed and commented. An empirical correlation between the Nusselt number and these parameters is proposed, allowing determination of the average natural convective heat transfer occurring in the hemispherical cavity.

Convective Heat Transfer in Elliptical Microchannels Under Slip Flow Regime and H1 Boundary Conditions

2015 ◽  
Vol 138 (4) ◽  
Author(s):  
Pamela Vocale ◽  
Gian Luca Morini ◽  
Marco Spiga
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Boundary Conditions ◽  
Convective Heat Transfer ◽  
Cross Section ◽  
Convective Heat ◽  
Slip Flow ◽  
The Cross ◽  
Cross Section Geometry

In this work, hydrodynamically and thermally fully developed gas flow through elliptical microchannels is numerically investigated. The Navier–Stokes and energy equations are solved by considering the first-order slip flow boundary conditions and by assuming that the wall heat flux is uniform in the axial direction, and the wall temperature is uniform in the peripheral direction (i.e., H1 boundary conditions). To take into account the microfabrication of the elliptical microchannels, different heated perimeter lengths are analyzed along the microchannel wetted perimeter. The influence of the cross section geometry on the convective heat transfer coefficient is also investigated by considering the most common values of the elliptic aspect ratio, from a practical point of view. The numerical results put in evidence that the Nusselt number is a decreasing function of the Knudsen number for all the considered configurations. On the contrary, the role of the cross section geometry in the convective heat transfer depends on the thermal boundary condition and on the rarefaction degree. With the aim to provide a useful tool for the designer, a correlation that allows evaluating the Nusselt number for any value of aspect ratio and for different working gases is proposed.

scholarly journals Statistical Analysis of the Effect of Nanoparticles Volume Fraction on Turbulent Forced Convective Heat Transfer Coefficient of Nanofluid in a Circular Tube

2015 ◽  
Vol 37 ◽  
pp. 141
Author(s):  
Farhad Vahidinia ◽  
Behrooz Keshtegar ◽  
Mohadeseh Miri
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Probability Distribution ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Volume Fraction ◽  
Circular Tube ◽  
Convective Heat Transfer Coefficient ◽  
Nanoparticles Volume Fraction

In this paper, the statistical analysis of the effect of nanoparticles volume fraction on one of the most important thermal characteristics turbulent flow of nanofluid i.e. convection heat transfer coefficient, inside a circular tube with uniform wall heat flux is investigated numerically. Also, water as a base fluid and Al2O3 as suspended particles with a diameter of 36 nm are considered. Heat transfer characteristics are computed using the solution of elliptic equations based on discrete the finite volume method and the second order upwind. The relationship between pressure and velocity using SIMPLEC algorithm is established. In this study, the variation of volume fraction of nanoparticles is assumed in the range of 0 to 6%. The best probability distribution function of the heat transfer parameters are selected using chi square test that various probability distribution such as: Gamma, Normal, Lognormal, Gumbel, and Frechet are evaluated based on numerical analysis of tube flow. After reviewing the results, it was found that with increasing volume fraction of nanoparticles, the convective heat transfer coefficient increases. On the other hand, the convective heat transfer coefficients with regard to variation of volume fraction of nanoparticles follow Gumbel Max probability distribution function.

scholarly journals Numerical study of heat transfer enhancement in the entrance region for low-pressure gaseous laminar pipe flows using Al2O3–air nanofluid

2018 ◽  
Vol 10 (7) ◽  
pp. 168781401878441 ◽  
Author(s):  
Wael Al-Kouz ◽  
Rafat Al-Waked ◽  
Ma’en Sari ◽  
Wahib Owhaib ◽  
Anas Atieh
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Knudsen Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Low Pressure ◽  
Entrance Region ◽  
Physical Parameters ◽  
Nanoparticles Volume Fraction

The gaseous low-pressure nanofluid flow of a steady-state two-dimensional laminar forced convection heat transfer in the entrance region of pipes is numerically investigated. Such flows are of interest for many engineering applications like the nuclear reactor and electronic equipment cooling, heat exchangers, and many others. Physical parameters considered in this study are Reynolds number ( Re), Prandtl number ( Pr), nanosolid particles volume fraction [Formula: see text], Knudsen number ( Kn), and the aspect ratio ( AR). These parameters ranges are as follows: [Formula: see text], [Formula: see text], [Formula: see text], [Formula: see text], and [Formula: see text]. The outcome of this study shows that by increasing Kn, velocity slip and temperature jump at the solid boundaries increase. In addition, heat transfer is enhanced by dispersing Al2O3 nanoparticles in the base low-pressure gaseous flow. Results show that there is no effect of the nanoparticles volume fraction with values below 0.03 on the average Nusselt number. The average Nusselt number increases [Formula: see text] as the value of the nanoparticles volume fraction exceeds 0.03. For instance, at Re = 1000, results show that when dispersing Al2O3 nanosolid particles with volume fractions of 0.3 and 0.5; there is an enhancement in the average Nusselt number of 30.35% and 136.74%, respectively, when compared to the case of dispersing Al2O3 nanosolid particles of 0.03 volume fraction.. Moreover, it is concluded that the average Nusselt number [Formula: see text] depends directly on Reynolds ( Re), Prandtl ( Pr) numbers, and the nanoparticles volume fraction [Formula: see text] and inversely on Knudsen number ( Kn) and the aspect ratio ( AR) for the investigated range of parameters considered in this study. Finally, a correlation of Nusselt number among all the investigated parameters in this study is proposed as [Formula: see text].

scholarly journals Control of the free convective heat transfer using a U-shaped obstacle in an Al2O3-water nanofluid filled cubic cavity

2021 ◽  
Vol 8 (7) ◽  
pp. 23-30
Author(s):  
Rajab Al-Sayagh ◽  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Free Convection ◽  
Convective Heat Transfer ◽  
Volume Fraction ◽  
Temperature Fields ◽  
Flow Structures ◽  
Nanoparticles Volume Fraction ◽  
Al2o3 Nanofluid

This paper deals with the study of free convection in a 3D enclosure filled with Al2O3-nanofluid and equipped with a U-shaped obstacle. The used U-shaped obstacle is considered perfectly conductive. The effect of the dimension and the orientation of the obstacle is investigated. In addition, the parameters governing the problem are varied as Rayleigh number (103 to 106), and nanoparticles volume fraction (0 to 7.5%). Results are depicted in terms of flow structures, temperature fields, and Nusselt number. Results show that the obstacle dimension and orientation can control the flow and optimize the heat transfer and the addition of nanoparticles enhances significantly Nusselt number.

scholarly journals Numerical Research on Convective Heat Transfer and Resistance Characteristics of Turbulent Duct Flow Containing Nanorod-Based Nanofluids

2018 ◽  
Vol 2018 ◽  
pp. 1-9
Author(s):  
Fangyang Yuan ◽  
Jianzhong Lin ◽  
Jianfeng Yu
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Volume Concentration ◽  
Flow Direction ◽  
Duct Flow ◽  
Particle Volume ◽  
Bulk Fluid

A coupled numerical model for nanorod-based suspension flow is constructed, and the convective heat transfer and resistance characteristics of the nanofluid duct flow are investigated. The numerical results are verified by experimental results and theoretical models. Most of nanorods are located randomly in the bulk fluid, while particles near the wall aligned with the flow direction. Friction factor of nanofluids with nanorods increases with higher particle volume concentration or aspect ratio, but the increment reduces when the Reynolds number gets larger. The relative Nusselt number is obtained to characterize the intensity of convective heat transfer. The results show that the Nusselt number of nanofluids increases when the particle volume concentration or aspect ratio becomes larger. Compared to increasing the aspect ratio of nanorods, increasing the particle volume concentration would be more effective on enhancing the convective heat transfer intensity in industrial applications although it will cause a slight increase of resistance.

Experimental Model of Temperature-Driven Nanofluid

2006 ◽  
Vol 129 (6) ◽  
pp. 697-704 ◽  
Author(s):  
A. G. Agwu Nnanna
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Small Volume ◽  
Volume Fraction ◽  
Convective Heat Transfer Coefficient ◽  
Isothermal Condition ◽  
Carrier Fluid ◽  
Small Volume Fraction ◽  
The Impact

This paper presents a systematic experimental method of studying the heat transfer behavior of buoyancy-driven nanofluids. The presence of nanoparticles in buoyancy-driven flows affects the thermophysical properties of the fluid and consequently alters the rate of heat transfer. The focus of this paper is to estimate the range of volume fractions that results in maximum thermal enhancement and the impact of volume fraction on Nusselt number. The test cell for the nanofluid is a two-dimensional rectangular enclosure with differentially heated vertical walls and adiabatic horizontal walls filled with 27 nm Al2O3–H2O nanofluid. Simulations were performed to measure the transient and steady-state thermal response of nanofluid to imposed isothermal condition. The volume fraction is varied between 0% and 8%. It is observed that the trend of the temporal and spatial evolution of temperature profile for the nanofluid mimics that of the carrier fluid. Hence, the behaviors of both fluids are similar. Results shows that for small volume fraction, 0.2⩽ϕ⩽2% the presence of the nanoparticles does not impede the free convective heat transfer, rather it augments the rate of heat transfer. However, for large volume fraction ϕ>2%, the convective heat transfer coefficient declines due to reduction in the Rayleigh number caused by increase in kinematic viscosity. Also, an empirical correlation for Nuϕ as a function of ϕ and Ra has been developed, and it is observed that the nanoparticle enhances heat transfer rate even at a small volume fraction.

Sign in / Sign up

Export Citation Format

Share Document