Exhaust Emissions from a Light-Duty Diesel Engine with SME-Diesel Fuel

2014 ◽  
Vol 1030-1032 ◽  
pp. 1176-1180
Author(s):  
Yang Xie ◽  
Yu Jie Hang ◽  
Hong Tao Wang ◽  
Hai Qing Shen ◽  
Cang Su Xu

Researchers have recently attempted to discover alternative energy sources that are accessible, technically viable, economically feasible, and environmentally acceptable. The objective of this study is to investigate regulated and unregulated exhaust emissions with petroleum diesel fuel and Jatrophabased biodiesel blends at proportions of 20%, 40%, 60%, 80% and 100% (v/v). This study examines three regulated emissions: CO, NMHC and NOx, and two typical unregulated emissions: SO2 and formaldehyde. The CO and formaldehyde emissions increase at low engine loads, and decrease at high engine loads. The NMHC and NOx emissions of the five fuels continuously decrease as biodiesel blends increase. Besides, SME fuels can also reduce the SO2 emissions.

Transport ◽  
2014 ◽  
Vol 29 (4) ◽  
pp. 440-448 ◽  
Author(s):  
Tomas Mickevičius ◽  
Stasys Slavinskas ◽  
Slawomir Wierzbicki ◽  
Kamil Duda

This paper presents a comparative analysis of the diesel engine performance and emission characteristics, when operating on diesel fuel and various diesel-biodiesel (B10, B20, B40, B60) blends, at various loads and engine speeds. The experimental tests were performed on a four-stroke, four-cylinder, direct injection, naturally aspirated, 60 kW diesel engine D-243. The in-cylinder pressure data was analysed to determine the ignition delay, the Heat Release Rate (HRR), maximum in-cylinder pressure and maximum pressure gradients. The influence of diesel-biodiesel blends on the Brake Specific Fuel Consumption (bsfc) and exhaust emissions was also investigated. The bench test results showed that when the engine running on blends B60 at full engine load and rated speed, the autoignition delay was 13.5% longer, in comparison with mineral diesel. Maximum cylinder pressure decreased about 1–2% when the amount of Rapeseed Methyl Ester (RME) expanded in the diesel fuel when operating at full load and 1400 min–1 speed. At rated mode, the minimum bsfc increased, when operating on biofuel blends compared to mineral diesel. The maximum brake thermal efficiency sustained at the levels from 0.3% to 6.5% lower in comparison with mineral diesel operating at full (100%) load. When the engine was running at maximum torque mode using diesel – RME fuel blends B10, B20, B40 and B60 the total emissions of nitrogen oxides decreased. At full and moderate load, the emission of carbon monoxide significantly raised as the amount of RME in fuel increased.


2015 ◽  
Vol 49 (12) ◽  
pp. 7473-7482 ◽  
Author(s):  
Adam Prokopowicz ◽  
Marzena Zaciera ◽  
Andrzej Sobczak ◽  
Piotr Bielaczyc ◽  
Joseph Woodburn

Author(s):  
Seppo A. Niemi ◽  
Juha M. Tyrva¨inen ◽  
Mika J. Laure´n ◽  
Va¨ino¨ O. K. Laiho

In the near future, crude oil based fuels must little by little be replaced by biofuels both in the region of the European Union (EU) and in the United States. Bearing this in mind, a Finnish-made off-road diesel engine was tested with a biofuel-diesel fuel blend in the Internal Combustion Engine (ICE) Laboratory of Turku Polytechnic, Finland. The biofuel was cold-pressed mustard seed oil (MSO). The engine operation, performance and exhaust emissions were investigated using a blend of 30 mass-% MSO and 70 mass-% diesel fuel oil (DFO). The injection timing of the engine was retarded considerably in order to reduce NOx emissions drastically. The main target was then to find out, whether the blended oxygen containing MSO would speed up the combustion so that the particulate matter (PM) emissions would remain unchanged or even decrease despite the injection retardation. As secondary tasks of the study, the NOx readings of the CLD and FTIR analyzers were compared, and exhaust contents of unregulated compounds were determined. Retarding the injection timing resulted in a significant decrease of NOx emissions, but in an increase in smoke, as expected. At retarded timing, the NOx emissions remained almost unchanged, but the amount of smoke decreased when the engine was run with the fuel blend instead of DFO. At retarded timing at rated speed, the number of ultra-fine particles decreased, but the amount of large particles increased with DFO at full load. At 10% load, however, the particle number increased in the entire particle size range due to retardation. At both loads, the use of the fuel blend slightly reduced larger particles, whereas the number of small particles somewhat increased. At full load at an intermediate speed of 1500 rpm, the PM results were very similar to those obtained at rated speed. At 10% load with DFO, however, the injection retardation led to a higher number of larger particles, the smaller particles being at almost an unchanged level. With the fuel blend, the particle number was now higher within almost the whole particle diameter range than with DFO. Considerably higher NO2 contents were usually detected with FTIR than with CLD. The shape of the NOx result curves were rather similar independent of which one of the analyzers was used for measurements. The NOx contents were, however, generally some ten ppms higher with FTIR. The exhaust contents of unregulated compounds were usually low.


2018 ◽  
Vol 225 ◽  
pp. 04025
Author(s):  
Mohd. Herzwan Hamzah ◽  
Azri Alias ◽  
Rizalman Mamat ◽  
Abdul Adam Abdullah ◽  
Agung Sudrajad ◽  
...  

Fossil fuel is non-renewable energy. This type of energy sources are widely used in many critical areas such as industrial application and vehicle application. Realizing this fact, many researches are conducted to produce alternative energy sources to reduce the dependence to fossil fuel for energy generation. As for example, fuels that produced from natural sources such as palm, rapeseed and jathropa are commonly used as alternative fuel especially for transportation purpose. Apart from natural sources, waste source such as used tires also can be utilized to produce alternative fuel. In this paper, the engine performance of diesel engine operating with unblended tire derived fuel (TDF) are analyzed and compared to diesel fuel. The experiment is conducted using a single cylinder, direct injection diesel engine. The engine operates at variable engine speed while constant load exerted to the engine. The performance parameters that are analyzed in the experiment includes engine power, engine torque, combustion pressure and exhaust gas temperature. Results from the experiment shows that diesel engine can operate with unblended TDF. However, TDF is not suitable for high engine speed applications. Furthermore, TDF produce lower performance output compared to diesel fuel.


2014 ◽  
Vol 926-930 ◽  
pp. 911-914
Author(s):  
Hong Zhi Wang

Biodiesel is a clean, renewable energy, non-burning emissions of sulfur dioxide, other harmful gases than conventional diesel fuel by 70 percent. This article outlines the concept of biofuels and main characteristics, focusing on the ship can be used as an alternative fuel biodiesel, analyzes the development prospects of bio-diesel.


Biodiesels which have been derived from non-edible vegetable oils are bagging the interest of researchers. These have been recognized as the potential alternatives of regular petroleum fuels. In this work, oil extracted from Juliflora seeds is converted as biodiesel by the transesterification process and used as alternative fuel in diesel engines. The tests are conducted by using diesel, B10, B20, B30 and B40. The experimental results of this study have disclosed that the Juliflora biodiesel blends have shown similar characteristics as diesel fuel. The BTE, CO, HC and smoke emissions are low for biodiesel blends while BSFC and NOx emissions are slightly higher. Taking all results into account it can be clinched that B10 blend of Juliflora biodiesel has viable option for diesel engine applications.


Author(s):  
Van Ha Pham ◽  
◽  
Ha Hiep Nguyen ◽  

The tests were carried out on the marine diesel engine operating by the load characteristic in seven modes, including five modes according to the test cycle D2 regulated by ISO 8178. Based on the experimental results obtained, the specific weighted NOx emissions and their average values were calculated and compared with IMO regulations. In addition, the study carried out a comparative experimental investigation on diesel fuel and dimethyl ether, and different injector opening pressures in the marine diesel engine to reduce its toxic exhaust emissions.


Sign in / Sign up

Export Citation Format

Share Document