scholarly journals The Effect of Ni Catalyst on the Growth of Multi-Walled Carbon Nanotubes by PECVD Method

2015 ◽  
Vol 1107 ◽  
pp. 314-319
Author(s):  
Mai Woon Lee ◽  
Muhammad Aniq Shazni Mohammad Haniff ◽  
Au Shih Teh ◽  
Daniel C.S. Bien ◽  
Soo Kien Chen ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Chemical Vapor ◽  
Growth Conditions ◽  
Ni Catalyst ◽  
Slight Variation ◽  
Initial Size ◽  
Catalyst Layers ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

In this paper, the effect of nickel (Ni) catalyst on the growth of carbon nanotubes (CNTs) was studied where the CNTs were vertically grown by plasma enhanced chemical vapor deposition (PECVD) method. The growth conditions were fixed at a temperature of 700°C with a pressure of 1000mTorr for 40 minutes with various thicknesses of sputtered Ni catalyst. Experimental results show that high density of CNTs was observed especially towards thicker catalyst layers where larger and taller nanotubes were formed. The growth rate increases by ~0.7 times with increasing catalyst thickness from 4nm to 10nm. The nucleation of the catalyst with various thicknesses was also studied as the absorption of the carbon feedstock is dependent on the initial size of the catalyst island. From the Raman results, we found that only slight variation in the intensity ratio of G-band over D-band as increasing catalyst thicknesses. The minor difference in G/D ratio indicates that the catalyst thickness does not significantly influence the quality of CNTs grown.

Calibration of reaction parameters for the improvement of thermal stability and crystalline quality of multi-walled carbon nanotubes

2010 ◽  
Vol 45 (3) ◽  
pp. 783-792 ◽  
Author(s):  
Saveria Santangelo ◽  
Giacomo Messina ◽  
Giuliana Faggio ◽  
Maurizio Lanza ◽  
Alessandro Pistone ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Thermal Stability ◽  
Crystalline Quality ◽  
Reaction Parameters ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

Effect of nanofiller on fibre laser drilling quality of carbon fibre reinforced polymer composite laminates

2018 ◽  
Vol 233 (4) ◽  
pp. 857-870
Author(s):  
Dhiraj Kumar ◽  
Kalyan Kumar Singh
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Fibre ◽  
Polymer Matrix ◽  
Composite Laminates ◽  
Reinforced Polymer ◽  
Carbon Fibre Reinforced Polymer ◽  
Multi Walled Carbon Nanotubes ◽  
Fibre Reinforced Polymer ◽  
Walled Carbon Nanotubes

Laser machining of carbon fibre reinforced polymer composites is a challenging task due to a significant difference between physical and thermal properties of the constituent materials, i.e. polymer matrix and carbon fibres. This results in extended heat-affected zone (HAZ), taper kerf and poor surface finishing. This paper focuses on an investigation, attempting to minimise the divergence in the decomposition temperature of carbon fibres and epoxy resin by adding multi-walled carbon nanotubes in polymer matrix as a secondary reinforcement. High thermal conductivity of multi-walled carbon nanotubes increases the thermal diffusivity of polymer matrix, which in turn reduces the matrix recession. In addition, laser power and scan speed was also considered as an input parameter and their influence on output responses such as HAZ, taper angle and surface roughness has been studied. To analyse the effect of multi-walled carbon nanotubes on the resultant thermal damage, an innovative technique, i.e. scanning acoustic microscopy was used. This technique provides a ply-by-ply damage analysis. C-scans of the top and bottom surface of the machined holes in the composite were also carried out. Further, micrographs of the holes were taken to analyse the quality of the holes using field-emission scanning electron microscope. The obtained results indicated that HAZ, taper angle and surface roughness of holes decreased by ∼30%, ∼47% and ∼43%, respectively, with 1.5 wt% multi-walled carbon nanotubes doped carbon fibre reinforced polymer laminates, when compared with the results obtained from experiments with neat carbon fibre reinforced polymer composite laminates.

Variation of Size and Alignment in Carbon Nanotubes by Changes of Growth Condition

2001 ◽  
Vol 7 (S2) ◽  
pp. 428-429
Author(s):  
Paula P. Provencio ◽  
Michael P. Siegal ◽  
Donald L. Overmyer
Keyword(s):  
Carbon Nanotubes ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Dwell Time ◽  
Chemical Vapor ◽  
Deposition Process ◽  
Nitrogen Atmosphere ◽  
Ni Catalyst ◽  
Multiwall Carbon Nanotube ◽  
Catalyst Layers

Carbon nanotubes have previously been grown on Ni coated glass, aligned vertical to the substrate over a multi-centimeter square area1. Under vacuum, the aligned nanotubes were grown below 666° C (strain point of the best display glass) by plasma-enhanced hot filament, chemical vapor deposition. It was found, the size and alignment of the nanotubes could be varied by changing the dwell time and the thickness of the catalytic Ni layer by plasma etching. in more recent, ongoing studies, the size of carbon nanotubes is varied by changing the growth temperature and dwell time under acetylene/nitrogen atmosphere using chemical vapor deposition onto W and Ni coated Si.Multiwall carbon nanotube films are grown using a thermally-activated chemical vapor deposition process. Thin Ni catalyst layers are sputtered onto W-coated Si(100) and reduced in a 600°C CO anneal. Nanotubes then grow at temperatures ranging from 630 - 790°C in an acetylene/nitrogen mixture.

Electron Microscopy and Raman Characterization of Multi-Walled Carbon Nanotubes Grown by Chemical Vapor Deposition

2008 ◽  
Vol 14 (S2) ◽  
pp. 304-305
Author(s):  
M Ellis ◽  
T Jutarosaga ◽  
S Smith ◽  
Y Wei ◽  
S Seraphin
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Chemical Vapor Deposition ◽  
New Mexico ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Raman Characterization

Extended abstract of a paper presented at Microscopy and Microanalysis 2008 in Albuquerque, New Mexico, USA, August 3 – August 7, 2008

The Effect of Inoculum in the Preparation of Fermented Tapioca for Nanotechnology Applications Based on FT-IR Studies

2013 ◽  
Vol 667 ◽  
pp. 534-537
Author(s):  
M.Z. Nuraini ◽  
S. Aishah ◽  
S.F. Nik ◽  
Mohamad Rusop
Keyword(s):  
Carbon Nanotubes ◽  
Gas Flow ◽  
Deposition Time ◽  
Chemical Vapor ◽  
Deposition Process ◽  
Ir Studies ◽  
Multi Walled Carbon Nanotubes ◽  
Ft Ir ◽  
Walled Carbon Nanotubes ◽  
Ft Ir Spectroscopy

Fermented tapioca which is a new starting material was used as a carbon precursor. Carbon nanotubes (CNTs) were deposited on silicon wafer (Si) by Thermal Chemical Vapor Deposition (TCVD). The gas flow of Argon (Ar) was constant at 70 bubbles per minute and 20 minutes of deposition time. Before the deposition process, silicon was coated with Nickel using spin coater. Various parameters such as amount of inoculums have been studied. Chemical functional groups of carbon nanotubes were characterized using FT-IR Spectroscopy. The FT-IR result shows peaks attributed to multi–walled carbon nanotubes (MWCNT) vibration modes.

Synthesis of Carbon Nanotubes from Polycyclic Compounds by CVD Method

2006 ◽  
Vol 320 ◽  
pp. 163-166 ◽  
Author(s):  
Koji Yamada ◽  
Kentaro Abe ◽  
Masafumi Mikami ◽  
Morihiro Saito ◽  
Jun Kuwano
Keyword(s):  
Carbon Nanotubes ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Quartz Substrate ◽  
Chemical Vapor ◽  
Polycyclic Compounds ◽  
Cvd Method ◽  
Multi Walled Carbon Nanotubes ◽  
Synthesis Of Carbon Nanotubes ◽  
Walled Carbon Nanotubes

Multi-walled carbon nanotubes (MWCNTs) were synthesized from camphor by a chemical vapor deposition (CVD) method in a range of 750-900. The catalyst was fed in three ways: (a) a sputtered Fe-film on a quartz substrate (b) vaporized ferrocene in an Ar flow; (c) both of (a) and (b). In the case (c), highly pure, dense and aligned MWCNT arrays formed on the quartz substrate at 850, whereas nonaligned MWCNTs formed in the cases (a) and (b).

Sign in / Sign up

Export Citation Format

Share Document