Investigation on Applicability of Pushover Analysis on High-Rise Diagonal Grid Structural System

2010 ◽  
Vol 163-167 ◽  
pp. 3918-3924
Author(s):  
Jun Teng ◽  
Hu Bing Tu ◽  
Huan Lin Mao ◽  
Ying Liang Qiu
Keyword(s):  
Seismic Analysis ◽  
Pushover Analysis ◽  
Incremental Dynamic Analysis ◽  
Analysis Method ◽  
Structural System ◽  
Base Shear ◽  
High Rise ◽  
Story Drift ◽  
Load Pattern ◽  
Global And Local

As an important seismic analysis method, Pushover is widely used in high-rise buildings, while there is still lack of investigation on applicability of Pushover analysis on diagonal grid structural system. Two structures with height 144 and 288 meters are respectively built, and then Pushover analysis and Incremental dynamic analysis are conducted. Results calculated by two different methods are compared, including top displacement vs. base shear curve, inter-story drift vs. inter-story shear curve, distribution of inter-story drift angle along the building height and plastic developing sequence of structural weak positions. Meanwhile, influence of three lateral load patterns (uniform pattern，inverted triangle pattern and SRSS pattern) on the results is investigated. Analysis results demonstrate that Pushover analysis can in some extent reflect seismic performance of structures and SRSS load pattern can better capture global and local information of structures compared with other two patterns.

scholarly journals Analysis of Multistory Buildings With Stub Column In Different Seismic Zones In India – A Review

2022 ◽  
pp. 44-49
Author(s):  
Somasundhara Naathan M ◽  
Dr Ramadevi K
Keyword(s):  
Seismic Analysis ◽  
Pushover Analysis ◽  
Seismic Load ◽  
Base Shear ◽  
Software Analysis ◽  
Multistory Buildings ◽  
Seismic Zones ◽  
Story Drift ◽  
Stub Column ◽  
Stub Columns

Construction of building requires proper planning and management. Buildings are subjected to various loads such as dead load, live load, wind load and seismic load. Seismic load has extreme adverse effect on building so it is necessary to perform seismic analysis. This paper explains about the response of building when it is subjected to seismic load, this response can be shown by story drift and base shear. Behavior of buildings with stub columns is analyzed and the results are compared with buildings without stub columns. Seismic analysis has been performed on (G+7) buildings located in seismic zones 2,3,4&5 using ETABS software. Analysis has been performed according to IS 1893:PartI (2002).The storey drift and design base shear are evaluated and compared. Pushover analysis was performed and the results were compared.

scholarly journals Investigation responses of the diagrid structural system of high-rise buildings equipped with Tuned mass damper using new dynamic method

2021 ◽  
Vol 1 (2) ◽  
Author(s):  
Arash Karimipour ◽  
Mansour Ghalehnovi ◽  
Mahmoud Edalati ◽  
Mehdi Barani
Keyword(s):  
Dynamic Method ◽  
Lateral Displacement ◽  
Tall Buildings ◽  
Tuned Mass Damper ◽  
Structural System ◽  
Base Shear ◽  
Structural Behaviour ◽  
High Rise ◽  
Mass Damper ◽  
Story Drift

Due to the shortage of land in cities and population growth, the significance of high rise buildings has risen. Controlling lateral displacement of structures under different loading such as an earthquake is an important issue for designers. One of the best systems is the diagrid method which is built with diagonal elements with no columns for manufacturing tall buildings. In this study, the effect of the distribution of the tuned mass damper (TMD) on the structural responses of diagrid tall buildings was investigated using a new dynamic method. So, a diagrid structural systems with variable height with TMDs was solved as an example of structure. The reason for the selection of the diagrid system was the formation of a stiffness matrix for the diagonal and angular elements. Therefore, the effect of TMDs distribution on the story drift, base shear and structural behaviour were studied. The obtained outcomes showed that the TMDs distribution does not significantly affect on improving the behaviour of the diagrid structural system during an earthquake. Furthermore, the new dynamic scheme represented in this study has good performance for analyzing different systems. 

scholarly journals SEISMIC ANALYSIS OF MULTISTORIED IRREGULAR AND REGULAR BUILDING WITH MASONARY INFILLS

2021 ◽  
Vol 5 (12) ◽  
Author(s):  
Ashutosh Shrivastava ◽  
Rajesh Chaturvedi
Keyword(s):  
Urban Areas ◽  
Seismic Analysis ◽  
Response Spectrum ◽  
Pushover Analysis ◽  
Seismic Zone ◽  
Soft Storey ◽  
High Rise ◽  
Frame Building ◽  
Performance Point ◽  
Open Ground

Nowadays, as in the urban areas the space available for the construction of buildings is limited. So in limited space we have to construct such type of buildings which can be used for multiple purposes such as lobbies, car parking etc. To fulfill this demand, high rise buildings is the only option available. The performance of a high rise building during strong earthquake motion depends on the distribution of stiffness, strength and mass along both the vertical and horizontal directions. If there is discontinuity in stiffness, strength and mass between adjoining storeys of a building then such a building is known as irregular building. The present study focuses on the seismic performance of regular and vertical irregular building with and without masonary infills. In the present study G+11 building is considered for the analysis with modelling and analysis done on ETABS software v17.0.1. The earthquake forces are calculated as per IS 1893 (part 1): 2016 for seismic zone III. The width of strut is calculated by using equivalent diagonal strut method. Total five models are considered for the analysis i.e. regular building with bare frame, regular building with masonary infill, soft storey building with open ground storey, mass irregular building with masonary infill and vertical geometric irregular building with masonary infill. The non-linear static analysis (pushover analysis) and linear dynamic analysis (response spectrum analysis) are performed for all the models and thereby compare their results. From analysis, the parameters like performance point, time period, maximum storey displacement, maximum storey drifts, storey shears and overturning moments are determined and also comparative study is done for all the models. From the comparison, it is observed that the vertical geometric irregular building shows better performance under seismic loading and bare frame building shows inferior performance. Moreover, the performance of masonary infilled frame building is f

Comparative study on seismic performance of specially shaped RC columns with that of rectangular columns in high-rise structures

2019 ◽  
Vol 11 (2) ◽  
pp. 202-215
Author(s):  
Shanmukha Shetty ◽  
Subrahmanya R.M. ◽  
Sushanth Bhandary ◽  
Thushar Shetty
Keyword(s):  
Pushover Analysis ◽  
Geometrical Shape ◽  
Structural Elements ◽  
Base Shear ◽  
Percent Reduction ◽  
Rc Columns ◽  
Content Type ◽  
High Rise ◽  
Rc Frames ◽  
Rectangular Columns

Purpose Columns are structural elements that are predominantly subjected to compressive forces and moments that are to be transferred from the super-structure to the sub-structure. The geometrical shape of a column is a significant factor to be considered. The paper aims to discuss this issue. Design/methodology/approach Pushover analysis is carried out, to study the behavior of RC frames with rectangular and specially shaped columns for the same building layout. Findings Reduction of 27.3 percent in base shear, 67.4 percent in spectral displacement, 66.5 percent reduction in storey displacement, 70.22 percent in storey drift and 0.315 percent reduction in storey shear is observed. Practical implications Special shaped RC columns can effectively enhance the structural behavior of high rise structures under seismic excitation in comparison to those with regular shaped RC columns. Originality/value Applications of special shaped columns in structures have showed a great deal of reduction in displacement and shear forces developed due to seismic activity, for the same area of concrete and steel as in rectangular columns.

Pushover Analysis of Base Isolated RC Frame Buildings With Masonry Infills

2019 ◽  
Vol 10 (2) ◽  
pp. 18-31
Author(s):  
Radhikesh Prasad Nanda ◽  
Subhrasmita Majumder
Keyword(s):  
Base Isolation ◽  
Plastic Hinge ◽  
Pushover Analysis ◽  
Base Shear ◽  
Infilled Frame ◽  
Masonry Infills ◽  
Time Period ◽  
Frame Buildings ◽  
Story Drift ◽  
Rc Frame Buildings

In the present article, the performance of base-isolated infilled frames is studied analytically. The seismic performances of four RC buildings, namely RC bare frame without isolator, RC bare frame with isolator, RC infilled frame without isolator, and RC infilled frame with isolator are analysed. The results show a decrease in base shear value and increase in time period due to base isolated buildings, while these parameters are reversely affected due to infills. The decrease in story drift for the base isolated buildings is in phase while considering infill. Also, it can be inferred that plastic hinge formation is greatly affected by the introduction of masonry infill. Hence, relying on base isolation without considering infills may underestimate the seismic performance.

Seismic Evaluation of Buildings with Plan Irregularity

2016 ◽  
Vol 857 ◽  
pp. 225-230 ◽  
Author(s):  
Ann Thomas Jereen ◽  
Soumya Anand ◽  
Binu M. Issac
Keyword(s):  
Lateral Stiffness ◽  
Lateral Loads ◽  
Base Shear ◽  
Seismic Evaluation ◽  
Maximum Displacement ◽  
Engineering Construction ◽  
High Rise ◽  
Story Drift ◽  
Modern Technologies ◽  
Plan Configuration

With the application of modern technologies in Civil Engineering, construction of high rise buildings with irregular plan configuration is increasing very quickly. Multi-story buildings are prone to lateral loads from wind or earthquake, which necessitates the need of seismic studies. Buildings can be designed to reduce these lateral loads by many methods; which is why the action of structural diaphragms have to be studied. Several studies have shown the effect of plan configuration on base shear, displacement and story drift, torsional buckling. The lateral stiffness of the building frame affects the maximum displacement of the structure due to earthquake. Study is done on various plan configuration buildings and the action of structural diaphragm on its performance during earthquake is studied.

scholarly journals Backstay Effect of Diaphragm in Tall Building

2020 ◽  
Vol 9 (3) ◽  
pp. 1578-1587
Keyword(s):  
Seismic Analysis ◽  
Response Spectrum ◽  
Retaining Wall ◽  
Tall Building ◽  
Structural Systems ◽  
Base Shear ◽  
High Rise ◽  
Structural Engineer ◽  
Structural Responses ◽  
Seismic Forces

Seismic analysis of structural systems with floor diaphragms has been a requisite in the recent past. The duty of a structural engineer is to be prudent about the behavior of every structural system adopted. Amongst the structural systems that are adopted world over, diaphragm with rigid and semi-rigid floor plate are adopted widely in the analysis. This research focuses on the backstay effect i.e. podium structural interaction with the tower area and consideration of retaining wall as increment of lateral stiffness as specified in latest tall building code IS6700:2016 for low and high rise structures. In the current study models were prepared with low to high rise storeys with rigid and flexible diaphragms considering backstay diaphragm placing tower at center and corner. The models were subjected to seismic forces; response spectrum along with the combination of the gravity loads. The structural responses like natural periods, base shear, displacement and inter storey drift were also studied.

scholarly journals SEISMIC EVALUATION OF HIGH RISE BUILDING WITH VERTICAL IRREGULARITIES BY PUSHOVER ANALYSIS

2021 ◽  
Vol 6 (2) ◽  
Author(s):  
Syed Shoaib ◽  
Syed Shoaib ◽  
Dr M L Waiker
Keyword(s):  
Structural Damage ◽  
Pushover Analysis ◽  
Vertical Plane ◽  
Base Shear ◽  
Seismic Evaluation ◽  
High Rise ◽  
Performance Point ◽  
Structural Irregularities ◽  
And Behavior ◽  
Static Pushover Analysis

During earthquake motion. The seismic behavior depends upon the strength, mass, and stiffness are distributed in both horizontal and vertical planes. the buildings structural damage was severe the frame is caused due to the discontinuity in the stiffness mass and strength between the alongside stories. The same type of discontinuity is vertical geometric irregularity which is due to the irregular building configuration in vertical plane so there is to know the seismic response of building modals in different structural irregularities. Non-linear static (pushover analysis) which is used for Investigation. The purpose of study doing nonlinear static (pushover analysis) by conventional design methodology G+12 High rise buildings this work shows seismic performance and behavior of building frame with and without vertical irregularity in terms of base shear, story shear, story displacement the performance point of all models are considered also found that irregularity in assessment of the structure decreases the performance level of building there is also reduces in deformation or displacement of the structure. all the models analyzed by using ETABS and design as per IS 456:200 and 1893:2016

scholarly journals Nonlinear Static Pushover Analysis of Medium Rise and High-Rise Building

2019 ◽  
pp. 255-561
Author(s):  
M Keshava Murthy ◽  
Ashwini L K
Keyword(s):  
Pushover Analysis ◽  
Performance Level ◽  
Base Shear ◽  
High Rise ◽  
High Rise Building ◽  
Non Linear ◽  
Nonlinear Static ◽  
Static Pushover Analysis ◽  
Different Levels ◽  
Nonlinear Static Pushover Analysis

Pushover analysis is an elegant tool to visualise the performance level of a building under a given earthquake. The purpose of the paper is to summarize the Non Linear static Pushover analysis of medium rise RC bare frame and high rise RC infilled structure with soft stories at different levels using ETABS software. Results concluded that due to the introduction of soft stories in the higher level the intensity of hinge formation becomes lower and lower and at the same time displacement and base shear increases

scholarly journals Pembandingan Perancangan Bangunan Tahan Gempa Menggunakan SNI 1726:2012 Dan SNI 1726:2019

2021 ◽  
Vol 18 (1) ◽  
pp. 88-99
Author(s):  
Azis Wicaksana ◽  
Anis Rosyidah
Keyword(s):  
Shear Force ◽  
Seismic Analysis ◽  
Building Design ◽  
Response Analysis ◽  
Base Shear ◽  
Seismic Resistant ◽  
Story Drift ◽  
Moment Resisting ◽  
Special Moment Resisting Frame ◽  
Spectrum Response

Indonesia has a code for designing a seismic-resistant building, which has always improved year after year. Start from Peraturan Perencanaan Tahan Gempa Indonesia Untuk Gedung (PPTI-UG) 1983, SNI 1726:2002, SNI 1726:2012, and the latest one is SNI 1726:2019. SNI 1726:2019 experienced some renewal on designing a seismic-resistant building. This research aims to compare spectrum response design and the structural behavior between seismic-resistant building design using SNI 1726:2012 and SNI 1726:2019. The reviewed structure behaviors are base shear force (V), drift (δmax), and story drift (Δ). The study compares the detail of the structural components as well as using SNI 2847:2013 and SNI 2847:2019. The research uses a 10-story building modeling that serves as an apartment building and located in the city of Banda Aceh. Seismic analysis using a spectrum response analysis with Special Moment Resisting Frame (SMRF) structure. The result showed that the peak acceleration (Sa) for the class sites of Medium Land (SD) and Hard Land (SC) were 11% and 26%, respectively, while for Soft Land (SE), there was no increase. The shear force in SNI 1726: 2019 has increased by 19.75% for the X direction and 19.97% for the Y direction. The increase in the shear force is directly proportional to the increase in drift and story drift. In the beam detailing and beam-column connection, there were no significant changes. While in the column detailing, there are additional provisions that cause the transverse reinforcement to be tighter.

Sign in / Sign up

Export Citation Format

Share Document