Numerical Simulation of Punching Bonding Based on AutoForm

2011 ◽  
Vol 189-193 ◽  
pp. 3423-3426
Author(s):  
Jiang Tao Wang ◽  
Ming Qian Shen ◽  
Tao Xue ◽  
Guo Hong Dai
Keyword(s):  
Numerical Simulation ◽  
Sheet Metal ◽  
Process Parameters ◽  
Limit Analysis ◽  
Die Design ◽  
Forming Limit ◽  
Stamping Die ◽  
Different Shapes ◽  
Simulation Results ◽  
Study Context

Punching bonding made for study context and Autoform selected for platform, numerical simulation of stamping was carried under different shapes, different materials, different parameters, and the different simulation results was gained . And deformation, the thickness of the forming limit analysis of simulation results, etc., and thus such important parameters as the thickness of sheet metal, punch diameter, the speed and the size of power punching and etc.,was modified and debuged, the combination of optimized process parameters of sheet metal was achieved in the final. Therefore, AutoForm not only can be used to overcome the difficulties,which there is no standard available, relying on repeated experiments to determine the parameters of the connected so as to achieve green design stamping; but also be made for stamping die design and production of connections to increase the efficiency and the expansion of the stamping connections the scope of the application.

Study on the Forming Process of the Crossmember in Car Intermediate Floor

2013 ◽  
Vol 442 ◽  
pp. 593-598
Author(s):  
Xue Xia Wang ◽  
Peng Chong Guan ◽  
Hai Peng Li ◽  
Li Hui Wang ◽  
Na Zhang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Model ◽  
Process Parameters ◽  
Thickness Distribution ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Simulation Technology ◽  
Forming Process ◽  
Distribution Diagram ◽  
Simulation Results

Flanging and bending forming processes of the crossmember in car intermediate floor are investigated respectively by using numerical simulation technology. The numerical model of the crossmember was established and its press forming effect was simulated to determine the feasible process parameters affecting its manufacturability. Forming limit diagram and thickness distribution diagram are used to evaluate simulation results of different process schemes. And then optimum values of process parameters for flanging and bending are found, which can reduce the tendencies of wrinkling, springback and crackling during the stamping of the product.

scholarly journals NUMERICAL SIMULATION TO STUDY EFFECT OF DIE DESIGN PARAMETERS ON DEFORMATION POSSIBILITY OF METAL ON COMBINED DRAWING

2018 ◽  
Vol 56 (3) ◽  
pp. 397
Author(s):  
Nguyen Manh Tien ◽  
Tran Duc Hoan ◽  
Nguyen Truong An ◽  
Pham Manh Tuan
Keyword(s):  
Numerical Simulation ◽  
Sheet Metal ◽  
Die Design ◽  
Design Parameters ◽  
Improve Product Quality ◽  
Drawing Process ◽  
Conical Die ◽  
Simulation Results ◽  
Cylindrical Cup ◽  
Deform 2D

This paper uses numerical simulation to study amethod in combined drawing process with thinning the wall when drawing of a cylindrical cup of sheet metal. The software Deform 2D is used to examineeffect of die design parameters (inclination of die) on deformation possibility of metal. Simulation results in order to select appropriate die design parameters (conical die), to enhance the ability to deform and contribute to improve product quality.

Study on the Forming Process Parameters of Automobile Front Panel Reinforcing Plate Using Orthogonal Experiment Method by Numerical Simulation Technology

2014 ◽  
Vol 543-547 ◽  
pp. 337-343
Author(s):  
Peng Chong Guan ◽  
Jia Wei Fan ◽  
Li Hui Wang ◽  
Hai Peng Li ◽  
Na Zhang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Process Parameters ◽  
Orthogonal Experiment ◽  
Die Design ◽  
Front Panel ◽  
Forming Limit ◽  
Simulation Technology ◽  
Forming Process ◽  
Experiment Method ◽  
Orthogonal Experiment Method

A methodology to design optimal forming process and relative parameters of the automobile front panel reinforcing plate, using the numerical simulation technology of forming sheet metal, is investigated. The digital model of the complex automobile part is established by computer aided design software. Dynaform software is used to simulate its forming process to acquire the feasible process parameters affecting its formability. Forming limit diagram and thickness distribution diagram are used to evaluate the simulation results of different process schemes. The orthogonal experiment method is adopted to design and simulate the process parameters to find out the optimum values for die design. The reasonable process design and optimum values of fillet radius of female die, friction coefficient and blank-holder force are obtained, which can reduce the tendencies of wrinkling, crackling and thickness reduction, and achieve sufficient plastic deformation of blank.

An Analysis of Drawing Process in Stamping Die Design for the Wheel Hub

2010 ◽  
Vol 142 ◽  
pp. 107-111
Author(s):  
Bai Liu
Keyword(s):  
Numerical Simulation ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Plastic Flow ◽  
Process Parameters ◽  
Die Design ◽  
Drawing Process ◽  
Element Analysis ◽  
Stamping Die ◽  
Stamping Process

Based on Finite Element Analysis (FEA) module of Dynaform software, the paper made numerical simulation of a wheel hub’s stamping process in the method of elastic-plastic flow, pointed out the behavior of deformation of stamping process, predicted and prevented stamping defect such as crack in the process, and calculated the degree of resilience. Consequently three forming numerical simulation schemes have been designed respectively, more feasible process parameters has been achieved in comparison with the features of each scheme.

Effect of Yield Criterion on Numerical Simulation Results Using a Stress-Based Failure Criterion

2006 ◽  
Vol 128 (3) ◽  
pp. 436-444 ◽  
Author(s):  
Aaron Sakash ◽  
Sumit Moondra ◽  
Brad L. Kinsey
Keyword(s):  
Numerical Simulation ◽  
Numerical Simulations ◽  
Sheet Metal ◽  
Failure Criterion ◽  
Path Dependence ◽  
Yield Criterion ◽  
Forming Limit Diagram ◽  
Dome Height ◽  
Forming Limit ◽  
Simulation Results

Determining tearing concerns in numerical simulations of sheet metal components is difficult since the traditional failure criterion, which is strain-based, exhibits a strain path dependence. A stress-based, as opposed to a strain-based, failure criterion has been proposed and demonstrated analytically, experimentally in tube forming, and through numerical simulations. The next step in this progression to the acceptance of a stress-based forming limit diagram is to demonstrate how this failure criterion can be used to predict failure of sheet metal parts in numerical simulations. In this paper, numerical simulation results for dome height specimens are presented and compared to experimental data. This procedure was repeated for various yield criteria to examine the effect of this parameter on the ability to predict failure in the numerical simulations. Reasonable agreement was obtained comparing the failure predicted from numerical simulations and those found experimentally, in particular for the yield criterion which has been shown to best characterize the material used in this study.

Optimization for Stamping Process Parameters of Front Fender Based on Numerical Simulation Technology

2010 ◽  
Vol 102-104 ◽  
pp. 232-236 ◽  
Author(s):  
Zhi Feng Liu ◽  
Qi Zhang ◽  
Wen Tong Yang ◽  
Jian Hua Wang ◽  
Yong Sheng Zhao
Keyword(s):  
Numerical Simulation ◽  
Sheet Metal ◽  
Process Parameters ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Simulation Analysis ◽  
Explicit Method ◽  
Simulation Technology ◽  
Stamping Process ◽  
Automotive Panel

According to the characteristic which is more and difficult to determine about the automotive panel forming factors, based on the dynamic explicit method, taking the typical automobile front fender for example, do the simulation analysis by using of DYNAFORM. On the premise of taking springback factors into account, analog the best stamping process parameters has been optimized from the analysis results after simulation such as sheet metal forming limited drawing(FLD)and sheet metal thinning drawing.

scholarly journals The Effect of Swinging Ball Heads with Different Arrangements in Multi-Point Stretch-Forming Process

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 337 ◽  
Author(s):  
Jian Xing ◽  
Yan-yan Cheng ◽  
Zhuo Yi
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Sheet Metal ◽  
Strain Distribution ◽  
Finite Element Models ◽  
Stretch Forming ◽  
Forming Process ◽  
Forming Quality ◽  
Staggered Arrangement ◽  
Simulation Results

To improve the effect of multi-point stretch forming of sheet metal, it is proposed in this paper to replace a fixed ball head with a swinging ball head. According to the multi-point dies with different arrangements, this research establishes finite element models of the following stretch forming, i.e., fixed ball heads with conventional arrangement, swinging ball heads with conventional arrangement, swinging ball heads with declining staggered arrangement, and swinging ball heads with parallel staggered arrangement, and then numerical simulation is performed. The simulation results show that by replacing a fixed ball head with a swinging ball head, the surface indentation of the part formed was effectively suppressed, the stress and tension strain distribution of the part formed was improved, and the forming quality was improved; the thickness of the elastic pad was reduced, the springback was reduced and the forming accuracy was improved; and when the ball head was applied to a multi-point die with staggered arrangement, a better forming result was achieved, where the best forming result was achieved in combining the swinging ball heads with the multi-point die with a parallel staggered arrangement. Forming experiments were carried out, and the experimental results were consistent with the trend of numerical simulation results, which verified the correctness of the numerical simulation.

Numerical Simulation and Process Research for Cylindrical Drawing

2010 ◽  
Vol 20-23 ◽  
pp. 1405-1408 ◽  
Author(s):  
Wei Hua Kuang ◽  
Qun Liu
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Process Research ◽  
Die Design ◽  
Drawing Process ◽  
3D Finite Element ◽  
Simulation Results ◽  
Distribution Of Stress

Drawing process is an important technology in shaping products. In the paper, the geometric surfaces of tools and sheet were modeled by Pro/E software, and a 3D finite element model of the cylindrical drawing process was developed by DYNAFORM. Numerical simulation results showed the distribution of stress, strain and thickness. FLD showed no material was in crack area and risk crack area. The drawing process could be successfully completed in one stroke. The simulation results were helpful for the die design.

The CAE Simulation of the Printer Cover Panel with Gas-Assisted Injection Molding

2012 ◽  
Vol 201-202 ◽  
pp. 808-811
Author(s):  
Guo Qiang Zhang ◽  
Mei Ting Xie ◽  
Wen Juan Wang ◽  
Ji Qiang Zhai
Keyword(s):  
Numerical Simulation ◽  
Injection Molding ◽  
Production Process ◽  
Process Parameters ◽  
Filling Process ◽  
Molding Process ◽  
Computer Aided ◽  
Simulation Results ◽  
Cae Technology ◽  
Cae Simulation

Numerical simulation in the printer cover product molding process with gas assisted injection molding was carried out by means of computer aided engineering. The filling process and surface quality were forecasted. The simulation results provide an important reference for the selection in the production process parameters. Compared with the production molding process and the actual product, CAE technology used in actual production and design is entirely feasible.

Sign in / Sign up

Export Citation Format

Share Document