Finite Element Analysis of Effects of Preheating and Postweld Heat Treatment on Residual Stress in Pipe Welding

2011 ◽  
Vol 314-316 ◽  
pp. 428-431 ◽  
Author(s):  
Hui Du ◽  
Dong Po Wang ◽  
Chun Xiu Liu ◽  
Hai Zhang
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element ◽  
Stress Distribution ◽  
Welding Process ◽  
Postweld Heat Treatment ◽  
Element Model ◽  
Element Analysis ◽  
Pipe Welding ◽  
Postweld Heat

To simulate preheating and postweld heat treatment of Q345 steel pipe welding, the finite element model was established. The welding process was simulated by method of the ANSYS element birth and death technique. In this paper, to obtain the distribution of the temperature field and stress field in different situations, preheating processes with two different values of temperature and postweld heat treatment process were simulated respectively. The results show that preheating can homogenize residual stress distribution of the weldment and decrease the residual stress. The heat treatment reduces the residual stress in inner and outer walls by 24% and 70% respectively and the stress distribution is more even and stress concentration is reduced.

Numerical Simulation of Influences of Preheating and Postweld Heat Treatment in Welding

2012 ◽  
Vol 538-541 ◽  
pp. 1518-1521
Author(s):  
Qing Yang ◽  
Shu Jun Xie ◽  
Tian Bao Yu
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Stress Distribution ◽  
Treatment Process ◽  
Postweld Heat Treatment ◽  
Element Model ◽  
Residual Stress Field ◽  
Pipe Welding ◽  
Postweld Heat ◽  
The Finite Element Model

In this paper, to investigative effects of preheating and postweld heat treatment on residual stress field in Q345 steel pipe welding, the finite element model was established. Preheating processes and postweld heat treatment process were simulated respectively. The results show that preheating can homogenize residual stress distribution of the weldment and decrease the residual stress. The heat treatment reduces the residual stress in inner and outer walls by 40% and 60% respectively and the stress distribution is more even and the stress concentration is reduced.

A Method for Applying Automatic Temperature Control to the Transient Finite Element Analysis of a Pressure Vessel Undergoing Postweld Heat Treatment

2004 ◽  
Author(s):  
Michael Sciascia
Keyword(s):  
Heat Treatment ◽  
Finite Element ◽  
Boundary Conditions ◽  
Temperature Profile ◽  
Pressure Vessel ◽  
Postweld Heat Treatment ◽  
Transient Temperature ◽  
Element Analysis ◽  
Heater Power ◽  
Postweld Heat

For complex finite element problems it is often desirable to prescribe boundary conditions that are difficult to quantify. The analysis of a pressure vessel undergoing postweld heat treatment (PWHT) is an example of such a problem. The PWHT process is governed by Code rules, but the temperature and gradient requirements they impose are not sufficient to precisely describe the complete vessel temperature profile. The imposition of such a profile in the analysis results in uncertainty and errors. A suitable but difficult approach is to specify heater power instead of temperatures, letting the solver determine the temperature profile. Unfortunately, the individual heater power levels necessary to meet the Code requirements are usually not known in advance. Determining the power levels necessary is particularly difficult if a transient solution is required. A means of actively controlling the heaters during the FEA solution is requirement for this approach. A simple and adaptive control algorithm was incorporated into the FEA solver via its scripting capability. Heat flux boundary conditions (heater power) were applied instead of transient temperature boundary conditions. Heater power levels were optimized to achieve predetermined time/temperature goals as the solution proceeded. The algorithm described was successfully applied to a pressure vessel PWHT with 14 zones of control. The approach may be adapted to other problems and boundary conditions.

scholarly journals Residual Stress Distribution in Feal Weld Overlay on Steel

1994 ◽  
Vol 364 ◽  
Author(s):  
X.-L. Wang ◽  
S. Spooner ◽  
C. R. Hubbard ◽  
P. J. Maziasz ◽  
G. M. Goodwin ◽  
...  
Keyword(s):  
Experimental Data ◽  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Post Weld Heat Treatment ◽  
Residual Stress Distribution ◽  
Element Analysis ◽  
Weld Overlay

AbstractNeutron diffraction was used to measure the residual stress distribution in an FeAl weld overlay on steel. It was found that the residual stresses accumulated during welding were essentially removed by the post-weld heat treatment that was applied to the specimen; most residual stresses in the specimen developed during cooling following the post-weld heat treatment. The experimental data were compared with a plasto-elastic finite element analysis. While some disagreement exists in absolute strain values, there is satisfactory agreement in strain spatial distribution between the experimental data and the finite element analysis.

Finite Element Analysis Model and Residual Stress Optimization in Rotor Welding Process

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Zhufeng Liu ◽  
Yonghui Xie ◽  
Hao Dang
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stress Distribution ◽  
Thermal Strain ◽  
Welding Process ◽  
Optimization Method ◽  
Mechanical Analysis ◽  
Analysis Model ◽  
Element Analysis ◽  
Stress Optimization

Abstract In this paper, the finite element method (FEM) is conducted for thermal and mechanical analysis of a half 2D axisymmetric welded rotor model. The temperature results after welding are obtained and supported by the experiment results. Furthermore, the thermal strain and residual stress of the weld are analyzed in detail by considering solid-state phase transformation (SSPT). Besides, parametric optimization method is adopted to optimize the region of large stress distribution. By choosing the weld pass number as the optimized parameter, the area decreases by 5.4% when the optimal pass number is 18. The axial and hoop stress distributions are obtained at the inner and outer surfaces near the weld for the better stress distribution.

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

2000 ◽  
Vol 123 (1) ◽  
pp. 150-154
Author(s):  
John H. Underwood ◽  
Michael J. Glennon
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Fatigue Life ◽  
Yield Strength ◽  
Residual Stresses ◽  
Solid Mechanics ◽  
Element Model ◽  
Pressure Vessels ◽  
Material Strength ◽  
Element Analysis

Laboratory fatigue life results are summarized from several test series of high-strength steel cannon breech closure assemblies pressurized by rapid application of hydraulic oil. The tests were performed to determine safe fatigue lives of high-pressure components at the breech end of the cannon and breech assembly. Careful reanalysis of the fatigue life tests provides data for stress and fatigue life models for breech components, over the following ranges of key parameters: 380–745 MPa cyclic internal pressure; 100–160 mm bore diameter cannon pressure vessels; 1040–1170 MPa yield strength A723 steel; no residual stress, shot peen residual stress, overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid mechanics analysis. Shot peen and overload residual stresses are modeled by superposing typical or calculated residual stress distributions on the applied stresses. Overload residual stresses are obtained directly from the finite element model of the breech, with the breech overload applied to the model in the same way as with actual components. Modeling of the fatigue life of the components is based on the fatigue intensity factor concept of Underwood and Parker, a fracture mechanics description of life that accounts for residual stresses, material yield strength and initial defect size. The fatigue life model describes six test conditions in a stress versus life plot with an R2 correlation of 0.94, and shows significantly lower correlation when known variations in yield strength, stress concentration factor, or residual stress are not included in the model input, thus demonstrating the model sensitivity to these variables.

Finite Element Analysis of the Rolling Contact Fatigue Life of Railcar Wheels

2008 ◽  
Vol 575-578 ◽  
pp. 1461-1466
Author(s):  
Byeong Choon Goo ◽  
Jung Won Seo
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Fatigue Life ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Element Analysis ◽  
Railway Vehicles ◽  
Contact Fatigue Life

Railcar wheels and axles belong to the most critical components in railway vehicles. The service conditions of railway vehicles have been more severe in recent years due to speed-up. Therefore, a more precise evaluation of railcar wheel life and safety has been requested. Wheel/rail contact fatigue and thermal cracks due to braking are two major mechanisms of the railcar wheel failure. One of the main sources influencing on the contact zone failure is residual stress. The residual stress in wheels formed during heat treatment in manufacturing changes in the process of braking. Thus the fatigue life of railcar wheels should be estimated by considering both thermal stress and rolling contact. Also, the effect of residual stress variation due to manufacturing process and braking process should be included in simulating contact fatigue behavior. In this paper, an evaluation procedure for the contact fatigue life of railcar wheels considering the effects of residual stresses due to heat treatment, braking and repeated contact load is proposed. And the cyclic stressstrain history for fatigue analysis is simulated by finite element analysis for the moving contact load.

Research on the Effects of Welding Sequence on Welding Residual Stress of High-Speed Train Based on SYSWELD

2011 ◽  
Vol 399-401 ◽  
pp. 1806-1811
Author(s):  
Yong Hong Chen ◽  
Peng Chen ◽  
Ai Qin Tian
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
High Speed ◽  
Element Model ◽  
Welding Residual Stress ◽  
High Speed Train ◽  
Distribution Law ◽  
Element Analysis ◽  
Welding Sequence ◽  
Maximum Residual Stress

The finite element model of the roof of aluminum high-speed train was established, double ellipsoid heat source was employed, and heat elastic-plastic theory was used to simulate welding residual stress of the component under different welding sequence based on the finite element analysis software SYSWELD. The distribution law of welding residual stress was obtained. And the effects of the welding sequence on the value and distribution of residual stress was analyzed. The numerical results showed that the simulation data agree well with experimental test data. The maximum residual stress appears in the weld seam and nearby. The residual stress value decreases far away from the welding center. Welding sequence has a significant impact on the final welding residual stress when welding the roof of aluminum body. The side whose residual stress needs to be controlled should be welded first.

FINITE ELEMENT ANALYSIS OF A DENTAL IMPLANT

2003 ◽  
Vol 15 (02) ◽  
pp. 82-85 ◽  
Author(s):  
SHYH-CHOUR HUANG ◽  
CHANG-FENG TSAI
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Element Model ◽  
Element Analysis ◽  
3 Dimensional ◽  
Dimensional Finite Element ◽  
The Stability ◽  
Stress Concentration Effect ◽  
Implant System

This paper presents results from using a 3-dimensional finite element model to assess the stress distribution in the bone, in the implant and in the abutment as a function of the implant's diameter and length. Increasing implant diameter and length increases the stability of the implant system. By using a finite element analysis, we show that implant length does not decrease the stress distribution of either the implant or the bone. Alternatively, however implant diameter increases reduce the stresses. For the latter case, the contact area between implant and bone is increased thus the stress concentration effect is decreased. Also, with increased implant diameter the bone loss is decreased and as a consequence the success rate is improved.

Cause Analysis and Preventive Measures against Cracks in 15Cr1Mo1V Steel Welded Joint in Service

2017 ◽  
Vol 863 ◽  
pp. 328-333
Author(s):  
Wei Shi ◽  
Yi Shi Lv ◽  
Zhong Bing Chen ◽  
Ling Hui Meng ◽  
Li Jun Zhang ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Stress Concentration ◽  
Welded Joint ◽  
Welding Process ◽  
Postweld Heat Treatment ◽  
Additional Stress ◽  
Heat Affect Zone ◽  
Crack Morphology ◽  
Deformation Ability ◽  
Postweld Heat

Characteristics and forming causes of the cracks in welded joint of 15Cr1Mo1V steel serviced 70000h are investigated by mechanical and chemical testing and crack morphology observation. Results show that the cracks initiate from welded metal or coarse grain heat affect zone (CGHAZ) near fusion line, and there are three kinds of defects observed in the crack region, which are macrocracks, microcracks and voids. According to the forming position, process and morphology of the cracks, it is estimated that the cracks are a kind of stress relief crack (SRC). The main reasons of the cracking are because of residual stress caused by improper temperature field during post welding heat treatment, strong stress concentration caused by welding structure, additional stress caused by abnormal hangers & supports and decreased ductility of welded joint in service. The SRC in welded joint can be avoided through optimizing the welding process and postweld heat treatment(PWHT) process to ensure enough critical ductility deformation ability εc and avoiding and reducing stress concentration and additional stress to decrease ductility deformation εP of welded joint which make εc>εp consistently.

Sign in / Sign up

Export Citation Format

Share Document