Numerical Simulation of Hot Rolled Coil Temperature Field in Hot Coil Box

2011 ◽  
Vol 338 ◽  
pp. 572-575
Author(s):  
Gui Jie Zhang ◽  
Kang Li ◽  
Ying Zi Wang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Temperature Field ◽  
Temperature Distribution ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Coil Temperature ◽  
Hot Rolled ◽  
Strip Coil ◽  
Good Agreement

The heat transfer model was developed and the heat transfer of the strip coil stay in the hot coil box was analyzed. The temperature distribution of the strip coil was investigated use the model. The measured results are in good agreement with the calculated ones, has a guiding significance to further improve the technology.

Heat Transfer Model and Analysis of Oil-Immersed Electrical Transformers with Heat Pipe Radiator

2012 ◽  
Vol 516-517 ◽  
pp. 312-315
Author(s):  
Guang Hua Li ◽  
Hong Lei Liu ◽  
De Jian Wang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Temperature Field ◽  
Heat Pipe ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Cooling Device ◽  
Transformer Design ◽  
Electrical Transformers ◽  
Good Agreement

This paper has formulated a heat transfer model for analyzing the cooling properties of a heat pipe cooling device of oil-immersed electrical transformer. Based on the model, the oil temperature field of a 30 KVA oil-immersed transformer has been numerical simulated, and experiments also had been conducted. Results showed that the numerical simulation has good agreement with experiment results. Results also showed that heat pipe radiator is feasible for oil-immersed electrical transformer cooling. The model can be used to analyze the oil temperature distribution properties in an oil-immersed electrical transformer with heat pipe cooling device, and provide theoretical guide for transformer design and improvement.

Study on Effective Radial Thermal Conductivity of Gas Flow through a Methanol Reactor

2015 ◽  
Vol 13 (1) ◽  
pp. 103-112 ◽  
Author(s):  
Kun Lei ◽  
Hongfang Ma ◽  
Haitao Zhang ◽  
Weiyong Ying ◽  
Dingye Fang
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Temperature Distribution ◽  
Large Scale ◽  
Gas Flow ◽  
Fixed Bed ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Particle Reynolds Number

Abstract The heat conduction performance of the methanol synthesis reactor is significant for the development of large-scale methanol production. The present work has measured the temperature distribution in the fixed bed at air volumetric flow rate 2.4–7 m3 · h−1, inlet air temperature 160–200°C and heating tube temperature 210–270°C. The effective radial thermal conductivity and effective wall heat transfer coefficient were derived based on the steady-state measurements and the two-dimensional heat transfer model. A correlation was proposed based on the experimental data, which related well the Nusselt number and the effective radial thermal conductivity to the particle Reynolds number ranging from 59.2 to 175.8. The heat transfer model combined with the correlation was used to calculate the temperature profiles. A comparison with the predicated temperature and the measurements was illustrated and the results showed that the predication agreed very well with the experimental results. All the absolute values of the relative errors were less than 10%, and the model was verified by experiments. Comparing the correlations of both this work with previously published showed that there are considerable discrepancies among them due to different experimental conditions. The influence of the particle Reynolds number on the temperature distribution inside the bed was also discussed and it was shown that improving particle Reynolds number contributed to enhance heat transfer in the fixed bed.

Heat transfer model for calculation of the temperature field inside thin-walled sections in fire

2021 ◽  
Vol 169 ◽  
pp. 108416
Author(s):  
Michał Malendowski ◽  
Wojciech Szymkuć ◽  
Piotr Turkowski ◽  
Adam Glema ◽  
Wojciech Węgrzyński
Keyword(s):  
Heat Transfer ◽  
Temperature Field ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Thin Walled ◽  
In Fire

Modeling of Temperature Distribution in Moving Webs in Roll-to-Roll Manufacturing

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Youwei Lu ◽  
Prabhakar R. Pagilla
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Thermal Strain ◽  
Heat Transfer Model ◽  
Operating Conditions ◽  
Transfer Model ◽  
Roll To Roll ◽  
Flexible Material ◽  
Process Line ◽  
The Web

A heat transfer model that can predict the temperature distribution in moving flexible composite materials (webs) for various heating/cooling conditions is developed in this paper. Heat transfer processes are widely employed in roll-to-roll (R2R) machines that are used to perform processing operations, such as printing, coating, embossing, and lamination, on a moving flexible material. The goal is to efficiently transport the webs over heating/cooling rollers and ovens within such processes. One of the key controlled variables in R2R transport is web tension. When webs are heated or cooled during transport, the temperature distribution in the web causes changes in the mechanical and physical material properties and induces thermal strain. Tension behavior is affected by these changes and thermal strain. To determine thermal strain and material property changes, one requires the distribution of temperature in moving webs. A multilayer heat transfer model for composite webs is developed in this paper. Based on this model, temperature distribution in the moving web is obtained for the web transported on a heat transfer roller and in a web span between two adjacent rollers. Boundary conditions that reflect many types of heating/cooling of webs are considered and discussed. Thermal contact resistance between the moving web and heat transfer roller surfaces is considered in the derivation of the heat transfer model. Model simulations are conducted for a section of a production R2R coating and fusion process line, and temperature data from these simulations are compared with measured data obtained at key locations within the process line. In addition to determining thermal strain in moving webs, the model is valuable in the design of heating/cooling sources required to obtain a certain desired temperature at a specific location within the process line. Further, the model can be used in determining temperature dependent parameters and the selection of operating conditions such as web speed.

Heat Transfer Modeling of Nanoparticle Packings on a Substrate

2018 ◽  
Author(s):  
Anil Yuksel ◽  
Edward T. Yu ◽  
Michael Cullinan ◽  
Jayathi Murthy
Keyword(s):  
Heat Transfer ◽  
Laser Power ◽  
Thermal Conductance ◽  
Heat Transfer Model ◽  
Experimental Result ◽  
Transfer Model ◽  
Heat Transfer Modeling ◽  
Interfacial Thermal Conductance ◽  
High Laser ◽  
Good Agreement

The temperature evolution of nanoparticle packings on a substrate under high laser power is investigated both experimentally and via numerical simulations. Numerical modeling of temperature distributions in copper nanoparticle packings on a glass substrate is performed and results are compared with experiment under 2.6 kW/cm2 laser power. A coupled electromagnetic-heat transfer model is implemented to understand the nanoparticle temperature distribution. Very good agreement between the coupled electromagnetic-heat transfer model and the experimental results is obtained by matching the interfacial thermal conductance, G, between the nanoparticles using the experimental result in the coupled electromagnetic-heat transfer model.

scholarly journals Calculation of temperature field of coiled wire using EFM

2018 ◽  
Vol 72 ◽  
pp. 03002
Author(s):  
Zhongjun Shu ◽  
Wei Shen ◽  
Qiang Li ◽  
Minghao Fan ◽  
Jiaqing Zhang
Keyword(s):  
Heat Transfer ◽  
Risk Assessment ◽  
Temperature Field ◽  
Fire Risk ◽  
Simulation Method ◽  
Heat Transfer Model ◽  
Numerical Results ◽  
Transfer Model ◽  
Fire Risk Assessment ◽  
Wire Method

Provided a heat transfer model of coiled wire method. Based on the method, a software of EFM (ANSYS) was used to calculate the temperature field of coiled wire. Comparisons between the experimental of RVS coiled wire and numerical results indicated the effectiveness of the method utilized. The simulation method based on EFM proved to be useful for the fire risk assessment of coiled wire.

Analytical Model for Heat Transfer Phenomena in Cup-Cast Method

2006 ◽  
Vol 116-117 ◽  
pp. 569-572
Author(s):  
Farshid Pahlevani ◽  
J. Yaokawa ◽  
M. Itamura ◽  
M. Kikuchi ◽  
O. Nagasawa ◽  
...  
Keyword(s):  
Heat Transfer ◽  
A356 Alloy ◽  
Nucleation And Growth ◽  
Heat Transfer Model ◽  
Solid Particles ◽  
Transfer Model ◽  
Heat Transfer Phenomenon ◽  
Semi Solid ◽  
Slurry Preparation ◽  
Good Agreement

Cup-cast method is a new method deals with semi-solid slurry preparation recently developed by the authors. In this method, suspension of globular solid particles in molten metal is prepared by controlling the nucleation and growth of solid-particles through the simplest and quickest techniques. In this method, heat transfer phenomenon plays an important role in governing the shape, size, and fraction of solid particles. In the current study, a heat transfer model was proposed and applied to Al-A356 alloy semi-solid slurry preparation. The heat transfer model was based on heat balance consideration between cup and slurry and it was in a good agreement with experimental results.

Specific Absorption Rate and Temperature Increase in Human Eye Subjected to Electromagnetic Fields at 900 MHz

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
Teerapot Wessapan ◽  
Phadungsak Rattanadecho
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Electromagnetic Fields ◽  
Absorption Rate ◽  
Specific Absorption Rate ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Specific Absorption ◽  
Eye Model ◽  
Human Eye

Human eye is one of the most sensitive parts of the entire human body when exposed to electromagnetic fields. These electromagnetic fields interact with the human eye and may lead to cause a variety of ocular effects from high intensity radiation. However, the resulting thermo-physiologic response of the human eye to electromagnetic fields is not well understood. In order to gain insight into the phenomena occurring within the human eye with temperature distribution induced by electromagnetic fields, a detailed knowledge of absorbed power distribution as well as temperature distribution is necessary. This study presents a numerical analysis of specific absorption rate (SAR) and heat transfer in the heterogeneous human eye model exposed to electromagnetic fields. In the heterogeneous human eye model, the effect of power density on specific absorption rate and temperature distribution within the human eye is systematically investigated. In particular, the results calculated from a developed heat transfer model, considered natural convection and porous media theory, are compared with the results obtained from a conventional heat transfer model (based on conduction heat transfer). In all cases, the temperatures obtained from the developed heat transfer model have a lower temperature gradient than that of the conventional heat transfer model. The specific absorption rate and the temperature distribution in various parts of the human eye during exposure to electromagnetic fields at 900 MHz, obtained by numerical solution of electromagnetic wave propagation and heat transfer equation, are also presented. The results show that the developed heat transfer model, which is the more accurate way to determine the temperature increase in the human eye due to electromagnetic energy absorption from electromagnetic field exposure.

Sign in / Sign up

Export Citation Format

Share Document