Mechanical Characterization of Polypropylene Natural Fibre Composites

2011 ◽  
Vol 383-390 ◽  
pp. 2737-2740 ◽  
Author(s):  
Sd Jacob Muthu ◽  
Ratnam Paskaramoorthy
Keyword(s):  
Mechanical Properties ◽  
Mechanical Characterization ◽  
Fibre Surface ◽  
Alkaline Treatment ◽  
Natural Fibre ◽  
Fibre Composites ◽  
The Matrix ◽  
Pp Composites ◽  
Fibre Loading

Using polypropylene (PP) as matrix and kenaf mat as reinforcement, composite test samples were fabricated by compression molding. Thereafter, the effect of fibre loading and the alkaline fibre surface treatment on the mechanical properties were studied. The kenaf/PP composites were found to have better mechanical properties than the polymer matrix. As expected, the interfacial bonding between the matrix and the fibres improved considerably when the fibres were subjected to alkaline treatment.

Fabrication and Characterization of Biocomposite Using Grewia Optiva Fibre (i.e. Bhimal) Reinforced Polyvinyl Alcohol (PVA)

2015 ◽  
Vol 1105 ◽  
pp. 51-55 ◽  
Author(s):  
K.M. Gupta ◽  
Kishor Kalauni
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Fibre ◽  
Fabrication Method ◽  
View Point ◽  
Engineering Material ◽  
Fibre Composites ◽  
Grewia Optiva ◽  
Fabrication And Characterization

Bhimal fibres are quite a newer kind of bio-degradable fibres. They have never been heard before in literatures from the view point of their utility as engineering material. These fibres have been utilized for investigation of their properties. Characterization of this fibre is essential to determine its properties for further use as reinforcing fibre in polymeric, bio-degradable and other kinds of matrix. With this objective, the fabrication method and other mechanical properties of Bhimal-reinforced-PVA biocomposite have been discussed. The stress-strain curves and load-deflection characteristics are obtained. The tensile, compressive, flexure and impact strengths have been calculated. The results are shown in tables and graphs. The results obtained are compared with other existing natural fibre biocomposites. From the observations, it has been concluded that the tensile strength of Bhimal-reinforced-PVA biocomposite is higher than other natural fibre composites. Hence these can be used as reinforcement to produce much lighter weight biocomposites.

scholarly journals Impact of Long-Term Weathering on the Properties of a Digestate-Based Biocomposite

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Marion Gebhardt ◽  
Markus Milwich ◽  
Götz T. Gresser ◽  
Andreas Lemmer
Keyword(s):  
Mechanical Properties ◽  
Natural Fibre ◽  
Material Strength ◽  
Plant Oil ◽  
High Increase ◽  
Long Term Stability ◽  
Fibre Composites ◽  
The Matrix ◽  
Main Substrate

AbstractNatural fibre composites are increasingly used. For many applications, the long-term stability of the mechanical properties is crucial. Therefore, the effects of weathering of a biocomposite made from fibrous digestate and bio-based thermoset are investigated. The fibre component of the composite comes from digestate of a German biogas station which processes hop vines as main substrate. The matrix is a plant-oil-based epoxy resin. The samples were alternately exposed to UV radiation and moisture for various lengths of time. Afterwards, the material strength and water absorption were tested. As a result, the weathering leads to a decrease of strength but not to a high increase of water uptake.

scholarly journals Synthesis and Characterization of ShortSaccaharum CilliareFibre Reinforced Polymer Composites

2009 ◽  
Vol 6 (1) ◽  
pp. 34-38 ◽  
Author(s):  
A. S. Singha ◽  
Vijay Kumar Thakur
Keyword(s):  
Mechanical Properties ◽  
Polymer Composites ◽  
Urea Formaldehyde ◽  
Thermal Studies ◽  
Synthesis And Characterization ◽  
Green Composites ◽  
Reinforced Polymer ◽  
The Matrix ◽  
Fibre Loading

This paper deals with the synthesis of shortSaccaharum Cilliarefibre (SC) reinforced Urea-Formaldehyde (UF) matrix based polymer composites. Present work reveals that mechanical properties such as: tensile strength, compressive strength, flexural strength and wear resistance of the UF matrix increase up to 30% fibre loading(in terms of weight) and then decreases for higher loading when fibers are incorporated into the matrix polymer. Morphological and Thermal studies of the matrix, fibre and short fibre reinforced (SF-Rnf) green composites have also been carried out. The results obtained emphasize the applications of these fibres, as potential reinforcing materials in bio based composites.

Mechanical characterization of LM25 alloy matrix composite reinforced with boron carbide

2021 ◽  
pp. 002199832110055
Author(s):  
Zeeshan Ahmad ◽  
Sabah Khan
Keyword(s):  
Tensile Strength ◽  
Boron Carbide ◽  
Mechanical Characterization ◽  
Stir Casting ◽  
Surface Mapping ◽  
Alloy Matrix ◽  
Casting Technique ◽  
The Matrix ◽  
Carbide Particles

Alumnium alloy LM 25 based composites reinforced with boron carbide at different weight fractions of 4%, 8%, and 12% were fabricated by stir casting technique. The microstructures and morphology of the fabricated composites were studied by scanning electron microscopy and energy dispersive spectroscopy. Elemental mapping of all fabricated composites were done to demonstrate the elements present in the matrix and fabricated composites. The results of microstructural analyses reveal homogenous dispersion of reinforcement particles in the matrix with some little amount of clustering found in composites reinforced with 12% wt. of boron carbide. The mechanical characterization is done for both alloy LM 25 and all fabricated composites based on hardness and tensile strength. The hardness increased from 13.6% to 21.31% and tensile strength 6.4% to 22.8% as reinforcement percentage of boron carbide particles increased from 0% to 12% wt. A fractured surface mapping was also done for all composites.

Mechanical Characterization of UV Photopolymerized PMMA with Different Photo-Initiator Concentration

2021 ◽  
Vol 903 ◽  
pp. 11-16
Author(s):  
M.A. Manjunath ◽  
K. Naveen ◽  
Prakash Vinod ◽  
N. Balashanmugam ◽  
M.R. Shankar
Keyword(s):  
Mechanical Properties ◽  
Light Source ◽  
Polymethyl Methacrylate ◽  
Biomedical Applications ◽  
Mechanical Characterization ◽  
Uv Light ◽  
Curing Time ◽  
Uv Led ◽  
Pmma Resin

Polymethyl methacrylate (PMMA) is one among few known photo-polymeric resin useful in lithography for fabricating structures having better mechanical properties to meet the requirement in electronics and biomedical applications. This study explores the effect of Photo Initiator (PI) concentration and also curing time on strength and hardness of Polymethyl methacrylate (PMMA) obtained by UV photopolymerization of Methyl methacrylate (MMA) monomer. The UV LED light source operating at the wavelength of 364 nm is used with Benzoin Ethyl Ether (BEE) as photo initiator. The curing of PMMA resin is supported with peltier cooling device placed at the bottom of the UV light source. The characterisation study of UV photo cured PMMA is analysed through nano indenter (Agilent Technologies-G200). The current work investigates the influence of PI concentration and curing time in achieving maximum mechanical properties for UV photopolymerized PMMA.

scholarly journals Characterization of continuous Hibiscus sabdariffa fibre reinforced epoxy composites

2022 ◽  
Vol 30 ◽  
pp. 096739112110609
Author(s):  
Atik Mubarak Kazi ◽  
Ramasastry DVA
Keyword(s):  
Fibre Orientation ◽  
Stress Transfer ◽  
Dynamic Mechanical Properties ◽  
Epoxy Composites ◽  
Neat Epoxy ◽  
Hibiscus Sabdariffa ◽  
Sem Images ◽  
Fibre Composites ◽  
The Matrix

The influence of fibre orientation on physical, mechanical and dynamic mechanical properties of Hibiscus sabdariffa fibre composites has been studied. The composites with longitudinal (0°), transverse (90°) and inclined (45°) fibre orientation were prepared using the hand layup technique. ASTM standards were used for characterization of continuous Hibiscus sabdariffa fibre composites. The composite with longitudinally placed fibres yields improved mechanical characteristics. The addition of longitudinal (0°) oriented continuous Hibiscus sabdariffa fibres to the epoxy enhances tensile strength by 460%, flexural strength by 160% and impact strength by 603% compared to neat epoxy. The longitudinal (0°) fibre oriented composite offers higher resistance to water absorption and thickness swelling compared to other types of composites. All continuous Hibiscus sabdariffa fibre epoxy composites possess an improved storage modulus than the neat epoxy resin. The glass transition temperature of continuous Hibiscus sabdariffa fibre composites is 8%–31% lower than that of neat epoxy. Scanning electron microscopy (SEM) images confirm the existence of voids in the matrix, fibre pullout and crack propagation near the fibre bundle, which indicates the stress transfer between fibre and matrix is non-uniform.

Rice Husk Reinforcement in Polymer Composites

2016 ◽  
pp. 165-191
Author(s):  
Sanjay Sharma ◽  
Deepak Verma
Keyword(s):  
Mechanical Properties ◽  
Rice Husk ◽  
Low Cost ◽  
Petroleum Products ◽  
Natural Fibre ◽  
Low Density ◽  
Thermal And Mechanical Properties ◽  
Coconut Husk ◽  
Fibre Composites ◽  
Petroleum Reserves

Increasing concern about global warming and depleting petroleum reserves and the high cost of petroleum products had made scientists to focus more on the use of natural fibres such as rice husk, baggase, coconut husk, hemp, sisal, jute, flax, banana etc. Past decade has shown many efforts to develop composites to replace the Petroleum and other non-decaying material products. Reinforcement with natural fibre in composites has recently gained attention due to low cost, easy availability, low density, acceptable, strength full, stiffness, ease of separation, enhanced energy recovery, biodegradability and recyclable in nature. Natural fibre composites are suitable as wood substitutes in the construction sector. All these have excellent physical, thermal and mechanical properties and can be utilized more effectively in the development of composite materials. In this connection, an investigation has been carried using rice husk, a natural fibre abundantly available in India.

Evaluation of Mechanical Properties of Sugarcane Reinforced Hybrid Natural Fibre Composites by Conventional Fabrication and Finite Element Method

2020 ◽  
Vol 841 ◽  
pp. 327-334
Author(s):  
Dhiwakar S. Ram ◽  
P.N. Bharath Kumar ◽  
R. Sandeep Kumar ◽  
B. Vijaya Ramnath
Keyword(s):  
Mechanical Properties ◽  
Finite Element Method ◽  
Finite Element ◽  
Composite Structures ◽  
Natural Fibre ◽  
Degradable Polymer ◽  
Reinforced Polymer ◽  
Fabrication Errors ◽  
Fibre Composites ◽  
Element Method

Natural Fibre composites are being widely used as a replacement to non-bio-degradable polymer composites. The unavailability of proper processes to treat the natural fibres and the errors in fabrication result in less accurate mechanical properties. The accuracy that is obtained by machine-based processes is not possible in Hand layup method, which is employed in fabrication of natural fibre composites. Finite Element method packages which are specially intended in modelling composite structures give more accurate result of properties than experimental setup, by avoiding fabrication errors. This paper evaluates Impact energy and then the tensile strength, flexural strength of a sugarcane fibre GFRP reinforced polymer matrix both by conventional Hand Layup method and also by Finite Element method.

Sign in / Sign up

Export Citation Format

Share Document