Performance of VoIP Networks Using MPLS Traffic Engineering

2012 ◽  
Vol 457-458 ◽  
pp. 927-930 ◽  
Author(s):  
Mohammed Faisal ◽  
Jia Uddin ◽  
Shimul Shil
Keyword(s):  
Traffic Engineering ◽  
Traffic Congestion ◽  
Network Performance ◽  
Ip Networks ◽  
Operating Efficiency ◽  
Voice Over Internet Protocol ◽  
Multiprotocol Label Switching ◽  
Network Congestion ◽  
Packet Losses ◽  
Data Packets

The implementation of Voice over Internet Protocol (VoIP) technology is on the increase because of its ability to enhance operating efficiency and reduce infrastructure cost. Voice and data packets traverse over IP networks with fixed maximum capacity. But susceptibility to traffic congestion which results in delay and packet losses is still a major challenge of VoIP technology. Multiprotocol Label Switching Protocol (MPLS) with Traffic Engineering (TE) is an approved standard technology that has the capabilities to minimize network congestion and improve network performance by reducing delay and packet loss to yield a higher throughput. In this paper, we investigate how MPLS Traffic Engineering can be implemented to reduce traffic congestion on VoIP networks.

scholarly journals Spectrum Based Power Management for Congested IoT Networks

Sensors ◽  
2021 ◽  
Vol 21 (8) ◽  
pp. 2681
Author(s):  
Kedir Mamo Besher ◽  
Juan Ivan Nieto-Hipolito ◽  
Raymundo Buenrostro-Mariscal ◽  
Mohammed Zamshed Ali
Keyword(s):  
Power Management ◽  
Network Performance ◽  
Channel Allocation ◽  
Battery Life ◽  
Packet Routing ◽  
Data Packets ◽  
Increasing Demand ◽  
Iot Devices ◽  
Set Up

With constantly increasing demand in connected society Internet of Things (IoT) network is frequently becoming congested. IoT sensor devices lose more power while transmitting data through congested IoT networks. Currently, in most scenarios, the distributed IoT devices in use have no effective spectrum based power management, and have no guarantee of a long term battery life while transmitting data through congested IoT networks. This puts user information at risk, which could lead to loss of important information in communication. In this paper, we studied the extra power consumed due to retransmission of IoT data packet and bad communication channel management in a congested IoT network. We propose a spectrum based power management solution that scans channel conditions when needed and utilizes the lowest congested channel for IoT packet routing. It also effectively measured power consumed in idle, connected, paging and synchronization status of a standard IoT device in a congested IoT network. In our proposed solution, a Freescale Freedom Development Board (FREDEVPLA) is used for managing channel related parameters. While supervising the congestion level and coordinating channel allocation at the FREDEVPLA level, our system configures MAC and Physical layer of IoT devices such that it provides the outstanding power utilization based on the operating network in connected mode compared to the basic IoT standard. A model has been set up and tested using freescale launchpads. Test data show that battery life of IoT devices using proposed spectrum based power management increases by at least 30% more than non-spectrum based power management methods embedded within IoT devices itself. Finally, we compared our results with the basic IoT standard, IEEE802.15.4. Furthermore, the proposed system saves lot of memory for IoT devices, improves overall IoT network performance, and above all, decrease the risk of losing data packets in communication. The detail analysis in this paper also opens up multiple avenues for further research in future use of channel scanning by FREDEVPLA board.

scholarly journals Bandwidth-Aware Rescheduling Mechanism in SDN-Based Data Center Networks

Electronics ◽  
2021 ◽  
Vol 10 (15) ◽  
pp. 1774
Author(s):  
Ming-Chin Chuang ◽  
Chia-Cheng Yen ◽  
Chia-Jui Hung
Keyword(s):  
Data Center ◽  
Completion Time ◽  
Network Performance ◽  
Data Locality ◽  
Task Completion ◽  
Data Center Networks ◽  
Task Completion Time ◽  
Data Packets ◽  
Network Bandwidth ◽  
Data Process

Recently, with the increase in network bandwidth, various cloud computing applications have become popular. A large number of network data packets will be generated in such a network. However, most existing network architectures cannot effectively handle big data, thereby necessitating an efficient mechanism to reduce task completion time when large amounts of data are processed in data center networks. Unfortunately, achieving the minimum task completion time in the Hadoop system is an NP-complete problem. Although many studies have proposed schemes for improving network performance, they have shortcomings that degrade their performance. For this reason, in this study, we propose a centralized solution, called the bandwidth-aware rescheduling (BARE) mechanism for software-defined network (SDN)-based data center networks. BARE improves network performance by employing a prefetching mechanism and a centralized network monitor to collect global information, sorting out the locality data process, splitting tasks, and executing a rescheduling mechanism with a scheduler to reduce task completion time. Finally, we used simulations to demonstrate our scheme’s effectiveness. Simulation results show that our scheme outperforms other existing schemes in terms of task completion time and the ratio of data locality.

Switching block studies, network performance evaluation and traffic engineering for ATM

2010 ◽  
Vol 5 (2) ◽  
pp. 187-198 ◽  
Author(s):  
Jordi Domingo ◽  
Herman Michiel ◽  
Reinhard Haberman ◽  
Matthias Sommer ◽  
Nikolas Mitrou ◽  
...  
Keyword(s):  
Performance Evaluation ◽  
Traffic Engineering ◽  
Network Performance ◽  
Network Performance Evaluation

scholarly journals Voice Over Internet Protocol Based Communication Design (VoIP) With 3CXSystemPhone On Android Smartphone

bit-Tech ◽  
2018 ◽  
Vol 1 (1) ◽  
pp. 1-8
Author(s):  
Riki Riki ◽  
Aditiya Hermawan ◽  
Yusuf Kurnia
Keyword(s):  
Internet Protocol ◽  
Scientific Work ◽  
Data Networks ◽  
Voice Over Internet Protocol ◽  
Computer Data ◽  
Communication Costs ◽  
Data Packets ◽  
Human Voice ◽  
Communication Design ◽  
The World

TCP\IP protocol can be connected to various computer data networks in the world. This protocol increasingly exists and is needed so that many parties develop it to vote through this protocol. Voice Over Internet Protocol technology is the answer to that desire. This technology is able to convert analog voice (human voice) into data packets then through public internet data networks and private intranet data packets are passed, so that communication can occur. With VoIP communication costs can be reduced so that it can reduce investment costs and conversations (cost saving) or even up to 100% free. VoIP implementation can be done by designing a wireless VoIP network (cable) using 3CXSystemPhone software as a PBX. In this scientific work the software used is 3CXSystemPhone 11.0, where SIP is a VoIP server which is a freeware software, in its application only requires one PC server and several PC clients (2 for example) that are connected to each other

scholarly journals ANALYSIS OF USER MOBILITY PERFORMANCE ON SOFTWARE DEFINED WIRELESS NETWORK USING DIJKSTRA ALGORITHM

2021 ◽  
Vol 2 (2) ◽  
pp. 127-133
Author(s):  
Icha Nurlaela Khoerotunisa ◽  
Sofia Naning Hertiana ◽  
Ridha Muldina Negara
Keyword(s):  
Wireless Network ◽  
Packet Loss ◽  
Network Performance ◽  
User Mobility ◽  
Dijkstra Algorithm ◽  
High Complexity ◽  
Quality Of Data ◽  
Data Packets ◽  
Mobility Performance

  Over the last decade, wireless devices have developed rapidly until predictions will develop with high complexity and dynamic. So that new capabilities are needed for wireless problems in this problem. Software Defined Network (SDN) is generally a wire-based network, but to meet the needs of users in terms of its implementation, it has begun to introduce a Wireless-based SDN called Software Defined Wireless Network (SDWN) which provides good service quality and reach and higher tools, so as to be able to provide new capabilities to wireless in a high complexity and very dynamic. When SDN is implemented in a wireless network it will require a routing solution that chooses paths due to network complexity. In this paper, SDWN is tested by being applied to mesh topologies of 4,6 and 8 access points (AP) because this topology is very often used in wireless-based networks. To improve network performance, Dijkstra's algorithm is added with the user mobility scheme used is RandomDirection. The Dijkstra algorithm was chosen because it is very effective compared to other algorithms. The performance measured in this study is Quality of Service (QoS), which is a parameter that indicates the quality of data packets in a network. The measurement results obtained show that the QoS value in this study meets the parameters considered by the ITU-T G1010 with a delay value of 1.3 ms for data services and packet loss below 0.1%. When compared with the ITU-T standard, the delay and packet loss fall into the very good category.

scholarly journals Virtual Link Aggregation Network Performance Using MikroTik Bonding

2020 ◽  
Vol 2 (2) ◽  
pp. 131-139
Author(s):  
Firmansyah Firmansyah ◽  
Mochamad Wahyudi ◽  
Rachmat Adi Purnama
Keyword(s):  
Quality Of Service ◽  
Transfer Rate ◽  
Network Performance ◽  
Data Packet ◽  
Virtual Link ◽  
Interface Bonding ◽  
Data Packets ◽  
Bandwidth Optimization ◽  
Network Link

Quality of Service in a network is a big thing that must be resolved and dealt with as best as possible. The limitation of the maximum transfer rate in network devices creates an obstacle in the process of transferring data packets. To maximize the transfer rate in network devices, you can use Virtual Link Aggregation which can offer bandwidth optimization and failover in the network. Link aggregation is a solution in combining several physical links into one logical link. The method used in this research is to consider the allocation of bandwidth, load balancing and failover in the link aggregation. From the results of the link aggregation test using two (2) interface bonding, the results of the bandwidth averages when there is a UPD data packet transfer to 0 bps / 184.9 Mbps, which was previously around 0 bps / 91.6 Mbps. While the result of the bandwidth averages when the TCP data packet transfer occurs is 0 bps / 105.5 Mbps, which was previously around 0 bps / 93.8 Mbps. Link Aggregation using a Mikrotik Router is a solution to produce a larger Throughput Bandwidth by combining two (2) Ethernet Physical Links into one logical link.

Reliability of Congestion Control Based on Packet Transmission Interval with Hybrid ARQ

2021 ◽  
pp. 2140004
Author(s):  
Mitsutaka Kimura ◽  
Mitsuhiro Imaizumi ◽  
Takahito Araki
Keyword(s):  
Congestion Control ◽  
Error Correction ◽  
High Performance ◽  
Data Communication ◽  
Window Size ◽  
Correction Method ◽  
Packet Transmission ◽  
Hybrid Arq ◽  
Packet Losses ◽  
Data Packets

Code error correction methods have been important techniques at a radio environment and video stream transmission. In general, when a server transmits some data packets to a client, the server resends the only loss packets. But in this method, a delay occurs in a transmission. In order to prevent the transmission delay, the loss packets are restored by the error correction packet on a client side. The code error correction method is called Hybrid Automatic Repeat reQuest (ARQ) and has been researched. On the other hand, congestion control schemes have been important techniques at a data communication. Some packet losses are generated by network congestion. In order to prevent some packet losses, the congestion control performs by prolonging packet transmission intervals, which is called High-performance and Flexible Protocol (HpFP). In this paper, we present a stochastic model of congestion control based on packet transmission interval with Hybrid ARQ for data transmission. That is, if the packet loss occurs, the data packet received in error is restored by the error correction packet. Moreover, if errors occur in data packets, the congestion control performs by prolonging packet transmission intervals. The mean time until packet transmissions succeed is derived analytically, and a window size which maximizes the quantity of packets per unit of time until the transmission succeeds is discussed.

scholarly journals Optimizations for Energy Efficiency in Software-Defined Wireless Sensor Networks

Sensors ◽  
2020 ◽  
Vol 20 (17) ◽  
pp. 4779
Author(s):  
Sorin Buzura ◽  
Bogdan Iancu ◽  
Vasile Dadarlat ◽  
Adrian Peculea ◽  
Emil Cebuc
Keyword(s):  
Energy Efficiency ◽  
Network Performance ◽  
Wireless Sensor ◽  
Management Approach ◽  
Control Plane ◽  
Data Broadcast ◽  
Data Packets ◽  
Similar Work ◽  
And Performance ◽  
The Individual

Software-defined wireless sensor networking (SDWSN) is an emerging networking architecture which is envisioned to become the main enabler for the internet of things (IoT). In this architecture, the sensors plane is managed by a control plane. With this separation, the network management is facilitated, and performance is improved in dynamic environments. One of the main issues a sensor environment is facing is the limited lifetime of network devices influenced by high levels of energy consumption. The current work proposes a system design which aims to improve the energy efficiency in an SDWSN by combining the concepts of content awareness and adaptive data broadcast. The purpose is to increase the sensors’ lifespan by reducing the number of generated data packets in the resource-constrained sensors plane of the network. The system has a distributed management approach, with content awareness being implemented at the individual programmable sensor level and the adaptive data broadcast being performed in the control plane. Several simulations were run on historical weather and the results show a significant decrease in network traffic. Compared to similar work in this area which focuses on improving energy efficiency with complex algorithms for routing, clustering, or caching, the current proposal employs simple computing procedures on each network device with a high impact on the overall network performance.

RSVP-TE Bilateral-Recursive Region Re-Routing Crankback Mechanism for Large-Scale Optical Networks

2019 ◽  
Vol 0 (0) ◽  
Author(s):  
Panke Qin ◽  
Jiawei Wang ◽  
Jingru Wu
Keyword(s):  
Real Time ◽  
Optical Networks ◽  
Traffic Engineering ◽  
Large Scale ◽  
Setup Time ◽  
Multiprotocol Label Switching ◽  
Transmission Scheme ◽  
Internet Applications ◽  
Time Dynamic ◽  
Reservation Protocol

AbstractCloud computing services and real-time Internet applications have spawned a large variety of potential requirements for quality of service (QoS), especially the latency and connection setup time. However, with the optical networks develop toward to larger scale, wider coverage and more users access, conventional resource reservation protocol traffic engineering (RSVP-TE) signal hop by hop transmission scheme cannot meet the requirements of these new applications for real-time dynamic services and fast restoration with long propagation delays. This paper proposes a novel RSVP-TE bilateral-recursive region re-routing crankback mechanism (BRCB) base on distributed path computation element (PCE) for generalized multiprotocol label switching (GMPLS) optical networks. In this mechanism, the backtracking nodes re-route and update the region routing paths which bypass the crankback and re-routing failure nodes when crankback occurs. It not only reduces the influencing factors of the scale of network, signaling crankback position and frequency to path connection setup time, but also avoids the backtracking of teardown messages.

Sign in / Sign up

Export Citation Format

Share Document