Nonlinear Analysis of I-Shaped Short Pier Shear Wall with Concealed Bracings

2012 ◽  
Vol 472-475 ◽  
pp. 757-760
Author(s):  
Ya E Li ◽  
Yu Hong Tang ◽  
Zhi Hua Li ◽  
Zhi Hai Hao
Keyword(s):  
Axial Compression ◽  
Compression Ratio ◽  
Seismic Behavior ◽  
Shear Wall ◽  
Wall Model ◽  
Skeleton Curve ◽  
Finite Element Software ◽  
Axial Compression Ratio ◽  
Concealed Bracings ◽  
Seismic System

In this paper, research on I-shaped short pier shear wall model which is the relatively weak seismic system components is presented. According to the results of Finite element software ABAQUS simulation, the influence of the bearing capacity, ductility and skeleton curve behavior on the I-shaped short pier shear wall with concealed bracings is mainly studied under different axial compression ratio and different reinforcement proportion of the concealed bracings. The results indicate that the I-shaped short pier shear wall with concealed bracings has a higher carrying capacity, and the ductility has also been enhanced. And the factor that axial compression ratio, reinforcement proportion of the concealed bracings significantly affect the seismic behavior of the I-shaped short pier shear wall with concealed bracings

Numerical Simulation Analysis on Seismic Behavior of Cold-Formed Beam-to-Column Connections

2010 ◽  
Vol 163-167 ◽  
pp. 692-696
Author(s):  
Yun Peng Chu ◽  
Yong Yao
Keyword(s):  
Bearing Capacity ◽  
Axial Compression ◽  
Compression Ratio ◽  
Welded Joints ◽  
Seismic Behavior ◽  
Great Influence ◽  
Hysteretic Behavior ◽  
Restoring Force ◽  
Finite Element Software ◽  
Axial Compression Ratio

The cold-formed square steel tubular with light weight has better seismic behavior and is suitable for construction in the area with high seismic fortification intensity. The reliability of joint connection greatly influence the safety reliability of structure, which’s restoring force characteristics under low cyclic loading need to be further researched. The finite element software ANSYS is used to do the research between two welded joints. The results show that : (1)Compared with typical welded joint, the ultimate bearing capacity of improved joint increase much, hysteretic curve is more plump, energy dissipation capacity enhance and stiffness degradation is slow. (2) Axial compression ratio has great influence on hysteretic behavior, bearing capacity and stiffness of common welded joints; however, there is a little effect on improved joint’s bearing capacity and stiffness. (3) After improved, the yield of joint has a longer yield platform, and under the same axial compression ratio condition, its yielding and ultimate load both obviously superior to common welded joints.

The Effect of Structural Parameters on Seismic Behavior of Concrete-Filled Steel Tubular Frames with Buckling-Restrained Brace

2012 ◽  
Vol 594-597 ◽  
pp. 1783-1787
Author(s):  
Feng Ming Ren ◽  
Jie Biao Zhang ◽  
Yun Zhou ◽  
Xiu Li Du
Keyword(s):  
Finite Element ◽  
Ultimate Strength ◽  
Axial Compression ◽  
Compression Ratio ◽  
Seismic Behavior ◽  
Structural Parameters ◽  
Skeleton Curve ◽  
Steel Ratio ◽  
Axial Compression Ratio ◽  
Column Section

In order to study the parameters influence on seismic behavior of concrete filled steel tubular (CFST) frame with bucking-restrained brace (BRB), the finite element analysis for CFST frame with BRB is studied in this paper, which is performed under low cyclic loading using the software of ABAQUS. Failure model and skeleton curve are comparative analyzed with the related experiment components, verifying that the finite element simulation of the CFST frame with BRB is effective. By changing the axial compression ratio of the column(n) and the steel ratio(α) of the column section respectively, the effect of the structural parameters on the seismic behavior of the CFST frames with BRB had been studied. The results shows that: with the increase of steel ratio of the column section, the lateral ultimate strength and the initial stiffness of the frame get higher, the lateral load(P) versus lateral displacement (Δ) hysteresis curves of the frame get plumper, and the energy dissipation of BRB remain basically unchanged; With the increase of axial compression ratio of the column, the lateral ultimate strength and the hysteretic behavior of the frame become low, whilst the energy dissipated by the BRB get higher.

Study on the Behaviors of Steel Reinforced Concrete Cloumns

2011 ◽  
Vol 368-373 ◽  
pp. 248-252
Author(s):  
Bao Sheng Yang ◽  
Yun Yun Li
Keyword(s):  
Bearing Capacity ◽  
Axial Compression ◽  
Compression Ratio ◽  
High Strength Concrete ◽  
Seismic Behavior ◽  
Slenderness Ratio ◽  
High Strength ◽  
Concrete Columns ◽  
Axial Compression Ratio ◽  
High Strength Concrete Columns

The influence on columns behaviors of slenderness ratio are analyzed, and the influence on columns’ anti-seismic behavior of axial compression ratio, stirrup ratio and steel form are analyzed through the test on bearing capacity and level load of low cycle reverse of steel reinforced high-strength concrete columns. The bearing capacity of the long columns reduces along with the slenderness ratio increasing and augments along with concrete strength increasing. Probability of suddenly destruct increases along with the column slenderness ratio augmenting through the test. In addition, anti-seismic behavior of columns are effected not only axial compression ratio, but also steel form. Axial compression coefficien of the steel reinforced high-strength concrete columns with different steel form may be adjusted, however, the influence of stirrup ratio is very little on anti-seismic behavior of columns.

The seismic performance of precast short-leg shear wall under cyclic loading

2020 ◽  
pp. 136943322096372
Author(s):  
Xiuli Du ◽  
Min Wu ◽  
Hongtao Liu
Keyword(s):  
Energy Consumption ◽  
Cyclic Loading ◽  
Axial Compression ◽  
Seismic Performance ◽  
Compression Ratio ◽  
Structural Parameters ◽  
Shear Wall ◽  
Shear Capacity ◽  
Axial Compression Ratio ◽  
Hysteretic Performance

In order to study the seismic performance of precast short-leg shear wall connected by grouting sleeves (PSSW), the three-dimensional numerical model was established by using the experiment of PSSW subjected to low cyclic loading. Based on good agreement between numerical results and experimental results, the numerical analysis models with different structural parameters of axial compression ratio and splicing position were designed in detail, and the effects of various parameters on the seismic performance of PSSW were analyzed. The results show that the PSSW exhibits wide and stable hysteresis loops, indicating a satisfactory hysteretic performance and an excellent energy consumption capacity. With the increase of the axial compression ratio, the shear capacity of horizontal splice seam is improved, but the ductility coefficient and total energy consumption decrease obviously. The most disadvantageous position of PSSW can be effectively avoided by changing the position of the post pouring seam. The bearing capacity of the specimens is basically stable, and the energy consumption increases significantly, so the post pouring seam of precast wall is recommended to be far away from the bottom section of the wall. In addition, the failure mechanism of different splicing positions was analyzed in detail.

Finite Element Analysis on Different Axial Compression Ratio of Composite CFST Column and Steel Beam Connection

2014 ◽  
Vol 578-579 ◽  
pp. 278-281
Author(s):  
Pi Yuan Xu ◽  
Qian Chen ◽  
Ya Feng Xu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Bearing Capacity ◽  
Axial Compression ◽  
Compression Ratio ◽  
Element Model ◽  
Element Analysis ◽  
Finite Element Software ◽  
Axial Compression Ratio ◽  
Modeling Process

In this paper, in order to understand fully the development of failure mechanism, bearing capacity and seismic performance of the steel H-beams and composite concrete filled steel tubular (CFST) column joints strengthened by outside strengthening ring, in the space zone the effects of changing the axial compression ratio is investigated. A 3D joint finite element model is built up by finite element software ABAQUS, the elastic-plastic finite element analysis is carried through numerical modeling process. The analysis results showed that low axial compression ratio has a little influence on the bearing capacity; with the increase of axial pressure the bearing capacity will decrease in a high axial compression ratio, moreover the failure pattern of joint changes from beam end to column end. The ductility of the specimens is decreased by raising axial compression ratio.

scholarly journals Insight into the Effect of Adhesive Interface on the Ultimate Capacity of the Double-Superposed Shear Wall

2018 ◽  
Vol 2018 ◽  
pp. 1-18
Author(s):  
Wenying Zhang ◽  
Lianping Yang ◽  
Shaole Yu ◽  
Xinxi Chen ◽  
Xuewei Zhang
Keyword(s):  
Bearing Capacity ◽  
Axial Compression ◽  
Compression Ratio ◽  
Precast Concrete ◽  
Boundary Elements ◽  
Shear Wall ◽  
Ultimate Bearing Capacity ◽  
Ultimate Capacity ◽  
Axial Compression Ratio ◽  
Adhesive Interface

This paper presents the results of a numerical and analytical study to investigate the effect of adhesive interface on the ultimate capacity of a new composite sandwich shear wall: double-superposed shear wall. The effect of adhesive interface on the ultimate capacity of two different wall configurations under different axial compression ratios was studied. The results indicate that, for the two different wall configurations, the bond strength of adhesive interface has a negligible effect on ultimate bearing capacity. As a result of the different intensity grades between cast-in-situ concrete wythe and precast concrete wythe, the double-superposed shear wall with precast boundary elements (wall configuration W3) yields a higher ultimate bearing capacity than that with cast-in-place boundary elements (wall configuration W2), when the axial compression ratio exceeds 0.2, which is contrary to the results under 0.1 axial compression ratio. A new calculation method for ultimate bearing capacity is proposed to take into account the different intensity grades, and the calculation results show a very good agreement with the numerical simulation results.

Influence of Axial Compression Ratio on Seismic Behavior of Reactive Powder Concrete (RPC) Beam-Column Joints

2014 ◽  
Vol 597 ◽  
pp. 312-315 ◽  
Author(s):  
Yan Zhong Ju ◽  
Chun Yu Li ◽  
De Hong Wang
Keyword(s):  
Bearing Capacity ◽  
Axial Compression ◽  
Compression Ratio ◽  
Seismic Behavior ◽  
Ultimate Bearing Capacity ◽  
Reactive Powder Concrete ◽  
Element Analysis ◽  
Axial Compression Ratio ◽  
Reactive Powder ◽  
Axial Compressive Ratio

To explore the influence of axial compressive ratio on seismic behavior of reactive powder concrete(RPC) beam-column joints,this paper carry out RPC beam-column joints nonlinear finite element analysis,using software ABAQUS.The effect of different axial compression ratio on the ductility,energy dissipation capacity and bearing capacity are studied,based on hysteretic curves and skeleton curves of the components.The results show that,with the increase of axial compression ratio,skeleton curves of the components tend to be steep when the vertical load of beam ends exceed the peak point.The ultimate bearing capacity of the components are improved with the increasing of axial compression ratio which is less then 0.6,while the ultimate bearing capacity show a opposite trend when the axial compressive ratio exceed 0.6.

Analysis of Seismic Performance of the Joint of Cellular Steel Column and Steel Beam in Different Axial Compression Ratio

2014 ◽  
Vol 578-579 ◽  
pp. 244-247
Author(s):  
Ya Feng Xu ◽  
Zhang Lin Zhai ◽  
Pi Yuan Xu
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Bearing Capacity ◽  
Axial Compression ◽  
Seismic Performance ◽  
Compression Ratio ◽  
Steel Beam ◽  
Finite Element Software ◽  
Axial Compression Ratio ◽  
Steel Column

This article researches seismic performance of the joint of cellular steel column and steel beam through simulation of the finite element software. With the change of axial force, we can attain the load-displacement hysteretic curves, skeleton curves under the different axial compression ratio, and then analyze their bearing capacity, ductility, energy dissipation and other mechanical properties. Results show that, the decrease of axial compression ratio is helpful to improve the bearing capacity of specimens. The joints of cellular steel column and steel beam have full hysteretic curve, good ductility and seismic performance.

Research on Defect and Adjustment of Complex Shear Wall Partitioned Design Method

2011 ◽  
Vol 243-249 ◽  
pp. 980-984
Author(s):  
Xue Yi Fu ◽  
Jia Xin Qu
Keyword(s):  
Axial Compression ◽  
Compression Ratio ◽  
Design Method ◽  
Concrete Strength ◽  
Shear Walls ◽  
Shear Wall ◽  
Axial Compression Ratio ◽  
Complex Shear ◽  
Section Design ◽  
Effective Flange Width

Both reference [1~2] method and partitioned design method (GB 50010-2002) were adopted to design complex shear walls, and some factors such as axial compression ratio, reinforcing ratio, section dimension, concrete strength grade and effective flange width were considered, then their limited loading capacity would be compared with each other when axial force was considered as a fixed value. It was found that there were some defects of complex shear wall partitioned design method. And its applied conditions were suggested, which included section restricted condition and limited value of axial compression ratio. When these conditions couldn’t be satisfied, the adjusted reinforcement partitioned design method of reference [3] was suggested. If the uneconomical problem of partitioned design method could not be accepted, whole section design method of reference [1~2] would be suggested.

Sign in / Sign up

Export Citation Format

Share Document