The Investigation of Preparing the Beta Zeolite Membrane by the Way of Secondary Growth

2012 ◽  
Vol 608-609 ◽  
pp. 1463-1466 ◽  
Author(s):  
Guo Lin Shao ◽  
Chun Ling Yu ◽  
Ying Huan Fu ◽  
Hong Yi Dai ◽  
Li Ping Zhang
Keyword(s):  
Secondary Growth ◽  
Dip Coating ◽  
Zeolite Membrane ◽  
Beta Zeolite ◽  
Self Assembling ◽  
Large Pore ◽  
Coating Method ◽  
Support Tube ◽  
Dip Coating Method ◽  
The Way

Beta zeolite membrane was prepared on the surface of α-Al2O3support tube with large pore by the way of secondary growth. Different seeding techniques, such as ultrasonic surge, self-assembling and dip-coating, were investigated, and the results indicated that the best one was dip-coating method for the support with large pore. The prepared membrane was characterized by SEM and XRD. It was proved that the beta zeolite membrane prepared by the way of secondary growth is continuous, dense and defect-free.

Y-Type Zeolite Membranes: Synthesis by Secondary by Method and Application in Treatment of Oily Effluents

2019 ◽  
Vol 958 ◽  
pp. 23-28
Author(s):  
Antonielly Santos Barbosa ◽  
Antusia Santos Barbosa ◽  
Meiry Gláucia Freire Rodrigues
Keyword(s):  
Zeolite Y ◽  
Dip Coating ◽  
Zeolite Membrane ◽  
Gamma Alumina ◽  
Zeolite Membranes ◽  
Water Emulsion ◽  
Ceramic Support ◽  
Coating Method ◽  
Dip Coating Method ◽  
Alpha Alumina

Several zeolite membrane types, including Mordenite (MOR), Linde Type A (LTA), and Faujasite (FAU), have been developed. Among these membranes, FAU zeolite membranes have a variety of applications, especially in the separation of mixtures that contain large molecules. The goal of this study is to use zeolite membranes (Y/alumina) to separate suspensions of oil-in-water emulsion. Two ceramic supports were prepared from the alumina at different sintering temperatures (700°C and 1200°C) to obtain gamma-alumina and alpha-alumina, respectively. The materials prepared, zeolite Y membranes/alpha-alumina and Y/gamma-alumina, were characterized using X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). The powder pressing method was used to compact the alpha-alumina and gamma-alumina ceramic support and the dip-coating method was used to prepare the zeolite Y membranes. The XRD pattern showed that the zeolite Y membrane/alumina obtained by the secondary growth dip-coating method, independent of the ceramic support used, showed no trace of the phases characterized as impurities. It was possible to observe a significant reduction in the concentration of oil in the permeate for the zeolite Y membranes, thus showing their potential for use in this application.

TiO2 Mesoporous Thick Films with Large-Pore Structure for Dye-Sensitized Solar Cell

2008 ◽  
Vol 8 (8) ◽  
pp. 3877-3882 ◽  
Author(s):  
Bo Chi ◽  
Li Zhao ◽  
Jian Li ◽  
Jian Pu ◽  
Yao Chen ◽  
...  
Keyword(s):  
Solar Cell ◽  
Dip Coating ◽  
Dye Sensitized Solar Cell ◽  
Structure Directing Agent ◽  
Dye Sensitized ◽  
Pluronic P123 ◽  
Large Pore ◽  
Mesoporous Film ◽  
Coating Method ◽  
Dip Coating Method

Large-pore mesoporous titania films with thickness up to 3.5 μm were prepared by dip-coating method using block copolymer Pluronic P123 as structure directing agent. The highly transparent multilayer mesoporous film shows a large pore size of 8.9 nm with surface area of 129.4 m2 · g−1. The mesopore structure with continuous crystalline framework was maintained after being calcined at 400 °C. Dye-sensitized solar cell (DSSC) based on the large-pore mesoporous film exhibited an enhanced light-to-electricity conversion efficiency of 6.01%, due to the thick large-pore mesoporous film with continuous crystalline framework structure.

scholarly journals Study the Effect of Seeding Suspension Concentration of DD3R Particles on the Modified Surface of Α-Alumina Support for Preparing DD3R Zeolite Membrane with High Quality

2018 ◽  
Vol 2 (1) ◽  
Author(s):  
Aynaz Meshkat ◽  
Mohammad Javad Vaezi ◽  
Ali Akbar Babaluo
Keyword(s):  
Secondary Growth ◽  
Dip Coating ◽  
Sem Analysis ◽  
Gas Permeation ◽  
Zeolite Membrane ◽  
Alumina Support ◽  
Suspension Concentration ◽  
Coating Method ◽  
Growth Method ◽  
Modified Surface

In this study, seeding of DD3R particles as an important step in the synthesis of DD3R membrane with secondary growth method was investigated. Dip-coating method is used for seeding of DD3R particles on the modified surface of α-alumina supports. 0.1, 0.2 and 0.3 wt% aqueous suspensions of the DD3R seeds were prepared and each support was coated three times with dipping time of 240 s. Scanning electron microscopy (SEM) analysis was used for the investigation of the quality of seed layer formed on the support. It is shown that the uniform layer of seeds was formed with 0.2 wt% seed suspension concentration. DD3R zeolite membrane was synthesized via hydrothermal method on the support seeded with 0.2 wt% seed suspension concentration. The X-ray diffraction and SEM analysis confirmed the synthesis of uniform DD3R zeolite membrane layer on the support which can be due to the uniform distribution of the DD3R seeds. Single gas permeation tests of N2, CO2 and CH4 were carried out, so that good perm-selectivity for gas mixtures was observed.

Porous Gel Coatings Obtained by Phase Separation in ORMOSIL System

2000 ◽  
Vol 628 ◽  
Author(s):  
Kazuki Nakanishi ◽  
Souichi Kumon ◽  
Kazuyuki Hirao ◽  
Hiroshi Jinnai
Keyword(s):  
Phase Separation ◽  
Reaction Time ◽  
Volume Fraction ◽  
Sol Gel ◽  
Reaction Times ◽  
Dip Coating ◽  
Coating Solution ◽  
Coating Method ◽  
Gel Phase ◽  
Dip Coating Method

ABSTRACTMacroporous silicate thick films were prepared by a sol-gel dip-coating method accompanied by the phase separation using methyl-trimethoxysilane (MTMS), nitric acid and dimethylformamide (DMF) as starting components. The morphology of the film varied to a large extent depending on the time elapsed after the hydrolysis until the dipping of the coating solution. On a glass substrate, the films prepared by early dipping had inhomogeneous submicrometer-sized pores on the surface of the film. At increased reaction times, relatively narrow sized isolated macropores were observed and their size gradually decreased with the increase of reaction time. On a polyester substrate, in contrast, micrometer-sized isolated spherical gel domains were homogeneously deposited by earlier dippings. With an increase of reaction time, the volume fraction of the gel phase increased, then the morphology of the coating transformed into co-continuous gel domains and macropores, and finally inverted into the continuous gel domains with isolated macropores. The overall morphological variation with the reaction time was explained in terms of the phase separation and the structure freezing by the forced gelation, both of which were induced by the evaporation of methanol during the dipping operation.

scholarly journals Preparation of Polypropylene/PVDF Composite Membrane by Dip-Coating Method

2021 ◽  
Vol 1115 (1) ◽  
pp. 012028
Author(s):  
P T P Aryanti ◽  
G Trilaksono ◽  
A Hotmaida ◽  
M A Afifah ◽  
F P Pratiwi ◽  
...  
Keyword(s):  
Composite Membrane ◽  
Dip Coating ◽  
Coating Method ◽  
Dip Coating Method

Characterization of UHMWPE- HAp coating produced by dip coating method on Ti6Al4V alloy

2021 ◽  
pp. 127091
Author(s):  
Gözde Çelebi Efe ◽  
Elif Yenilmez ◽  
İbrahim Altinsoy ◽  
Serbülent Türk ◽  
Cuma Bindal
Keyword(s):  
Dip Coating ◽  
Ti6al4v Alloy ◽  
Coating Method ◽  
Dip Coating Method

scholarly journals The Effect of Film Thickness and Content on Film Formation from PS/ Nanocomposites Prepared by Dip-Coating Method

2012 ◽  
Vol 2012 ◽  
pp. 1-17 ◽  
Author(s):  
M. Selin Sunay ◽  
Onder Pekcan ◽  
Saziye Ugur
Keyword(s):  
Film Thickness ◽  
Elevated Temperatures ◽  
Film Formation ◽  
Fluorescence Emission ◽  
Dip Coating ◽  
Atomic Force ◽  
Annealing Step ◽  
Coating Method ◽  
Fluorescence Emission Intensity ◽  
Dip Coating Method

Steady-state fluorescence (SSF) technique in conjunction with UV-visible (UVV) technique and atomic force microscope (AFM) was used for studying film formation from TiO2covered nanosized polystyrene (PS) latex particles (320 nm). The effects of film thickness and TiO2content on the film formation and structure properties of PS/TiO2composites were studied. For this purpose, two different sets of PS films with thicknesses of 5 and 20 μm were prepared from pyrene-(P-) labeled PS particles and covered with various layers of TiO2using dip-coating method. These films were then annealed at elevated temperatures above glass transition temperature () of PS in the range of 100–280°C. Fluorescence emission intensity, from P and transmitted light intensity, were measured after each annealing step to monitor the stages of film formation. The results showed that film formation from PS latexes occurs on the top surface of PS/TiO2composites and thus developed independent of TiO2content for both film sets. But the surface morphology of the films was found to vary with both TiO2content and film thickness. After removal of PS, thin films provide a quite ordered porous structure while thick films showed nonporous structure.

Preparation and properties of polyurethane coatings modified by polysilazane

2019 ◽  
Vol 32 (6) ◽  
pp. 611-619 ◽  
Author(s):  
Xiaoli Liu ◽  
Zhen Ge ◽  
Wenguo Zhang ◽  
Yunjun Luo
Keyword(s):  
Mechanical Property ◽  
Photoelectron Spectroscopy ◽  
Composite Coatings ◽  
Composite Films ◽  
Dip Coating ◽  
Water Contact ◽  
Research Attention ◽  
Elongation At Break ◽  
Coating Method ◽  
Dip Coating Method

Due to their unique physicochemical properties, polysilazanes exhibit excellent performance when combined with some resin matrixes, which had drawn great research attention. In this article, polyurethane (PU) was firstly prepared by polytetrahydrofuran glycol, isophorone diisocyanate, and 1,4-butanediol as main materials. Then, the prepared PU was blended with polysilazane by mixing the two solutions together, which was cured to films via dip-coating method at room temperature. The structure, thermal stability, and surface properties of the composite coatings were investigated by Fourier-transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, and X-ray photoelectron spectroscopy. The results demonstrated that after modification with polysilazane, the heat resistance, hydrophobicity, and mechanical property of the PU coatings were improved. When the content of polysilazane was 6 wt%, the mechanical property of the composite films was optimized, with a maximum tensile strength of 25.7 MPa and elongation at break of 797%. Meanwhile, the water contact angle of the composite film was 107° and the water absorption reached a minimum of 2.1%, which showed improved hydrophobicity and water resistance.

Sign in / Sign up

Export Citation Format

Share Document