The Programming Strategie of High Speed Milling on Aluminum Ally Bowl-Shaped and Thin-Walled Part by Using Powermill Software

2013 ◽  
Vol 706-708 ◽  
pp. 357-360
Author(s):  
Xin Gui Lin ◽  
Gen Miao Yi

According to the particularity of aluminium alloy thin-walled bowl, the programming strategies for high-speed milling process were analyzed, including the tool path strategies, leading in/out, and the tool path connections. A programming example was used to illustrate the practical application of Powermill software in high-speed milling of aluminium alloy thin-walled bowl.

2009 ◽  
Vol 69-70 ◽  
pp. 428-432 ◽  
Author(s):  
Qing Hua Song ◽  
Yi Wan ◽  
Shui Qing Yu ◽  
Xing Ai ◽  
J.Y. Pang

A method for predicting the stability of thin-walled workpiece milling process is described. The proposed approach takes into account the dynamic characteristics of workpiece changing with tool positions. A dedicated thin-walled workpiece representative of a typical industrial application is designed and modeled by finite element method (FEM). The workpiece frequency response function (FRF) depending on tool positions is obtained. A specific 3D stability chart (SC) for different spindle speeds and different tool positions is then elaborated by scanning the dynamic properties of workpiece along the machined direction throughout the machining process. The dynamic optimization of cutting parameters for increasing the chatter free material removal rate and surface finish is presented through considering the chatter vibration and forced vibration. The investigations are compared and verified by high speed milling experiments with flexible workpiece.


2011 ◽  
Vol 223 ◽  
pp. 456-463 ◽  
Author(s):  
Bei Zhi Li ◽  
Xiao Hui Jiang ◽  
Huai Jing Jing ◽  
Xiao Yan Zuo

With FEM software of AdvantEdge, a model was created to analyze cutting force and thermal in the high-speed milling process, this model included a complete milling process of cutter radius. Combined with experiments validation, in high-speed milling, the normal force is greater than the tangential force and result in greater residual stress of that direction, which indicates that mechanical force play an essential part on the formation of residual stress. When the speed is over certain scope, the cutting force decreases, but the cutting temperature has been rising. In Roughing, by limiting the range of high-speed the residual tensile stress impact can be reduced. While in finishing, as the feed rate reducing the residual tensile stress will decrease greatly, improving the surface quality of thin-walled parts.


2011 ◽  
Vol 418-420 ◽  
pp. 840-843
Author(s):  
Qing Hua Song ◽  
Xing Ai

The efficiency of the high-speed milling process is often limited by the occurrence of chatter. In order to predict the occurrence of chatter, accurate models are necessary. With the speed increasing, gyroscopic effect plays an important pole on the system behavior, including dynamic characteristic and rotating behavior. Considering the influence of gyroscopic effect on rotating behavior, an updated model for the milling process is presented which features as model of the equivalent profile of tool. In combination with this model, a nonlinear instantaneous cutting force model is proposed. The use of this updated equivalent profile of tool results in significant differences in the static uncut thickness compared to the traditional model.


2011 ◽  
Vol 117-119 ◽  
pp. 1851-1856 ◽  
Author(s):  
Song Mei Yuan ◽  
He Lei Zhang

A new method for vibration control of aeronautical thin-walled workpiece in high-speed milling progress using a dynamic vibration absorber is presented. First, the theoretical model of the method is established and studied. Then the effectiveness of this method is testified via the simulation based on FEM. Finally, the feasibility of this method is discussed. The result shows that this method for vibration control of the aeronautic thin-walled workpiece in high-speed milling progress is effective and practical.


Micromachines ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 88
Author(s):  
Yupeng Xin ◽  
Yuanheng Li ◽  
Wenhui Li ◽  
Gangfeng Wang

Cavities are typical features in aeronautical structural parts and molds. For high-speed milling of multi-cavity parts, a reasonable processing sequence planning can significantly affect the machining accuracy and efficiency. This paper proposes an improved continuous peripheral milling method for multi-cavity based on ant colony optimization algorithm (ACO). Firstly, by analyzing the mathematical model of cavity corner milling process, the geometric center of the corner is selected as the initial tool feed position. Subsequently, the tool path is globally optimized through ant colony dissemination and pheromone perception for path solution of multi-cavity milling. With the advantages of ant colony parallel search and pheromone positive feedback, the searching efficiency of the global shortest processing path is effectively improved. Finally, the milling programming of an aeronautical structural part is taken as a sample to verify the effectiveness of the proposed methodology. Compared with zigzag milling and genetic algorithm (GA)-based peripheral milling modes in the computer aided manufacturing (CAM) software, the results show that the ACO-based methodology can shorten the milling time of a sample part by more than 13%.


Author(s):  
Hongji Zhang ◽  
Yuanyuan Ge ◽  
Hong Tang ◽  
Yaoyao Shi ◽  
Zengsheng Li

Within the scope of high speed milling process parameters, analyzed and discussed the effects of spindle speed, feed rate, milling depth and milling width on milling forces in the process of high speed milling of AM50A magnesium alloy. At the same time, the influence of milling parameters on the surface roughness of AM50A magnesium alloy has been revealed by means of the measurement of surface roughness and surface micro topography. High speed milling experiments of AM50A magnesium alloy were carried out by factorial design. Form the analysis of experimental results, The milling parameters, which have significant influence on milling force in high speed milling of AM50A magnesium alloy, are milling depth, milling width and feed speed, and the nonlinear characteristics of milling force and milling parameters. The milling force decreases with the increase of spindle in the given mill parameters. For the effects of milling parameters on surface quality of the performance, in the milling depth and feeding speed under certain conditions with the spindle speed increases the surface quality of AM50A magnesium alloy becomes better with the feed speed increases the surface quality becomes poor. When the spindle speed is greater than 12000r/min, the milling depth is less than 0.2mm, and the feed speed is less than 400mm/min, the milling surface quality can be obtained easily.


Sign in / Sign up

Export Citation Format

Share Document