A Study of the Sensitivity of Parameters Affecting Surface Roughness in High Speed Milling Superalloy GH4169

2013 ◽  
Vol 711 ◽  
pp. 143-148 ◽  
Author(s):  
Wei Wei Liu ◽  
Xu Sheng Wan ◽  
Xiao Yan Li ◽  
Yuan Yu ◽  
Dong Fang Wang
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Orthogonal Experiment ◽  
Relative Sensitivity ◽  
Depth Of Cut ◽  
High Temperature Alloy ◽  
High Speed Milling ◽  
Genetic Algorithm Method ◽  
Coated Carbide ◽  
Carbide Inserts

The orthogonal experiment is processed for high-speed milling superalloy GH4169 with TiAlN coated carbide inserts. The empirical formula of the surface roughness is acquired by using Genetic Algorithm method. On the basis of this formula, studying the absolute sensitivity and relative sensitivity of surface roughness for milling speed, depth of cut and feed; The results showed that in the process of high-speed milling of high-temperature alloy GH4169, Surface roughness is most sensitive to the change of milling feed; change of milling depth take second place and milling speed is the least sensitive.

A Study of the Sensitivity of Parameters Affecting Coated Tool Life in High Speed Milling Superalloy GH4169

2013 ◽  
Vol 651 ◽  
pp. 436-441
Author(s):  
Wei Wei Liu ◽  
Xu Sheng Wan ◽  
Yuan Yu ◽  
Feng Li ◽  
Hao Chen
Keyword(s):  
High Temperature ◽  
Tool Life ◽  
High Speed ◽  
Depth Of Cut ◽  
Linear Regression Method ◽  
Carbide Tool ◽  
High Temperature Alloy ◽  
High Speed Milling ◽  
Coated Carbide Tool ◽  
Coated Carbide

Through the orthogonal test of the TiALN coated carbide tool high-speed milling of high-temperature alloy GH4169, the empirical formula of the tool life are acquired by using multiple linear regression method. On the basis of this formula, studying the absolute sensitivity and relative sensitivity of TiALN coated carbide tool life for milling speed, depth of cut and feed; The results showed that in the process of high-speed milling of high-temperature alloy GH4169, tool life decreased with the increase of milling speed, feed and depth of cut; tool life is most sensitive to the change of milling speed; change of feed take second place and milling depth is the least sensitive.

Design Optimization of Cutting Parameters Using Taguchi Method and ANOVA during High-Speed Machining Hardened H13 Steel

2009 ◽  
Vol 626-627 ◽  
pp. 129-134
Author(s):  
Song Zhang ◽  
Y.B. Guo
Keyword(s):  
Surface Roughness ◽  
Design Optimization ◽  
High Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
High Speed Machining ◽  
H13 Steel ◽  
High Speed Milling ◽  
Optimization Of Cutting Parameters ◽  
Coated Carbide

High-speed machining thoroughly hardened tool steels has emerged as a competitive finishing technology for making dies and molds. The objective of this paper is to develop an optimization method for the better (i. e., lower value) surface roughness in terms of cutting parameters when high-speed milling hardened H13 steel. The cutting parameters to be considered were cutting speed, feed per tooth, radial depth of cut, and axial depth of cut, respectively. A series of high-speed milling experiments of hardened H13 steel using PVD coated carbide inserts without any cutting fluids were performed to measure the surface roughness data. Taguchi orthogonal arrays, signal-to-noise (S/N) ratio, and analysis of variance (ANOVA) were used to evaluate the effects of cutting parameters on surface roughness and to find the optimal factor/level combination for the better surface roughness. The investigations of this study would be used for design optimization of cutting parameters to obtain the better surface roughness.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

Machining Evaluation of High-Speed Milling for Thin-Wall Machining of Al7075-T651

2014 ◽  
Vol 541-542 ◽  
pp. 785-791 ◽  
Author(s):  
Joon Young Koo ◽  
Pyeong Ho Kim ◽  
Moon Ho Cho ◽  
Hyuk Kim ◽  
Jeong Kyu Oh ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Integrity ◽  
Cutting Forces ◽  
High Speed ◽  
Surface Condition ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Thin Wall ◽  
Machined Surface ◽  
High Speed Milling

This paper presents finite element method (FEM) and experimental analysis on high-speed milling for thin-wall machining of Al7075-T651. Changes in cutting forces, temperature, and chip morphology according to cutting conditions are analyzed using FEM. Results of machining experiments are analyzed in terms of cutting forces and surface integrity such as surface roughness and surface condition. Variables of cutting conditions are feed per tooth, spindle speed, and axial depth of cut. Cutting conditions to improve surface integrity were investigated by analysis on cutting forces and surface roughness, and machined surface condition.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

The effect of monolayer TiCN-, AlTiN-, TiAlN-and two layers TiCN + TiN- and AlTiN + TiN-coated cutting tools on tool wear, cutting force, surface roughness and chip morphology during high-speed milling of Ti6Al4V titanium alloy

2016 ◽  
Vol 232 (7) ◽  
pp. 1273-1286 ◽  
Author(s):  
Emel Kuram
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Tool Wear ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Tools ◽  
Chip Morphology ◽  
High Speed Milling ◽  
Ti6al4v Titanium Alloy ◽  
Coated Carbide

Tool coatings can improve the machinability performance of difficult-to-cut materials such as titanium alloys. Therefore, in the current work, high-speed milling of Ti6Al4V titanium alloy was carried out to determine the performance of various coated cutting tools. Five types of coated carbide inserts – monolayer TiCN, AlTiN, TiAlN and two layers TiCN + TiN and AlTiN + TiN, which were deposited by physical vapour deposition – were employed in the experiments. Tool wear, cutting force, surface roughness and chip morphology were evaluated and compared for different coated tools. To understand the tool wear modes and mechanisms, detailed scanning electron microscope analysis combined with energy dispersive X-ray of the worn inserts were conducted. Abrasion, adhesion, chipping and mechanical crack on flank face and coating delamination, adhesion and crater wear on rake face were observed during high-speed milling of Ti6Al4V titanium alloy. In terms of tool wear, the lowest value was obtained with TiCN-coated insert. It was also found that at the beginning of the machining pass TiAlN-coated insert and at the end of machining TiCN-coated insert gave the lowest cutting force and surface roughness values. No change in chip morphology was observed with different coated inserts.

Experimental Investigation on High-Speed Milling of Aluminum Alloys

2011 ◽  
Vol 418-420 ◽  
pp. 1141-1147
Author(s):  
Yong Liu ◽  
Li Tang Zhang ◽  
Zhi Hong Xu
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Experimental Investigation ◽  
Aluminum Alloys ◽  
High Speed ◽  
Depth Of Cut ◽  
Processing Temperature ◽  
Single Factor ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling is recognized as one of rapidly development machining methods. The article gives details of machining experiments with different aluminum alloys. Through a lot of single factor experiments and the orthogonal multi-factor experiments, and also use method of semi-artificial thermocouple. This paper mainly studies influence of surface roughness and residual stress with changed rotate speed, tooth load and radial depth of cut, and changed law of processing temperature for rotate speed. Though experiments shows that enhancing rotate speed may reduce surface roughness and residual stress within certain limits and the result of experiments is not agree with Carl Salomon’s theory.

scholarly journals Optimisation of the Machining of Stellite 6 PTA Hardfacing Using Surface Roughness

2010 ◽  
Vol 443 ◽  
pp. 227-231 ◽  
Author(s):  
Md Shahanur Hasan ◽  
Md Mazid Abdul ◽  
Richard E. Clegg
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Deposition Process ◽  
Depth Of Cut ◽  
High Corrosion Resistance ◽  
Turning Operations ◽  
Stellite 6 ◽  
Cutting Regimes ◽  
Coated Carbide ◽  
Carbide Inserts

Stellites are cobalt based super alloys. By virtue of their excellent physio-mechanical properties, stellites are highly regarded engineering materials. Stellites posses high corrosion resistance and wear resistance properties. This study investigates the Stellite deposition process and machinability of Stellite 6 deposited on steel subtrate. Stellite 6 was deposited onto a 4140 bar using a plasma transfer arc (PTA) system and machinability was assessed on the basis of surface roughness. A series of turning operations have been carried out on a conventional lathe using coated carbide inserts and surface roughness was evaluated by Stylus type Surtronic3+ instrument. The values of surface roughness were plotted against different cutting speed, feed rate and depth of cut to display the results in graphical forms. Optimal cutting regimes were established against the best values of surface roughness.

scholarly journals Analysis of tool wear and surface roughness in high-speed milling process of aluminum alloy Al6061

2021 ◽  
pp. 71-84
Author(s):  
Nhu-Tung Nguyen ◽  
Dung Hoang Tien ◽  
Nguyen Tien Tung ◽  
Nguyen Duc Luan
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Tool Wear ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Speed ◽  
Milling Process ◽  
Face Milling ◽  
Depth Of Cut ◽  
High Speed Milling

In this study, the influence of cutting parameters and machining time on the tool wear and surface roughness was investigated in high-speed milling process of Al6061 using face carbide inserts. Taguchi experimental matrix (L9) was chosen to design and conduct the experimental research with three input parameters (feed rate, cutting speed, and axial depth of cut). Tool wear (VB) and surface roughness (Ra) after different machining strokes (after 10, 30, and 50 machining strokes) were selected as the output parameters. In almost cases of high-speed face milling process, the most significant factor that influenced on the tool wear was cutting speed (84.94 % after 10 machining strokes, 52.13 % after 30 machining strokes, and 68.58 % after 50 machining strokes), and the most significant factors that influenced on the surface roughness were depth of cut and feed rate (70.54 % after 10 machining strokes, 43.28 % after 30 machining strokes, and 30.97 % after 50 machining strokes for depth of cut. And 22.01 % after 10 machining strokes, 44.39 % after 30 machining strokes, and 66.58 % after 50 machining strokes for feed rate). Linear regression was the most suitable regression of VB and Ra with the determination coefficients (R2) from 88.00 % to 91.99 % for VB, and from 90.24 % to 96.84 % for Ra. These regression models were successfully verified by comparison between predicted and measured results of VB and Ra. Besides, the relationship of VB, Ra, and different machining strokes was also investigated and evaluated. Tool wear, surface roughness models, and their relationship that were found in this study can be used to improve the surface quality and reduce the tool wear in the high-speed face milling of aluminum alloy Al6061

Surface Quality of High Speed Milling of Silicon Carbide by Using Diamond Coated Tool

2013 ◽  
Vol 446-447 ◽  
pp. 275-278 ◽  
Author(s):  
Mohammad Iqbal ◽  
Mohamed Konneh ◽  
Ahmad Yasir Bin Md Said ◽  
Azri Fadhlan Bin Mohd Zaini
Keyword(s):  
Surface Roughness ◽  
Silicon Carbide ◽  
High Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Work Piece ◽  
Model Interaction ◽  
High Speed Milling ◽  
Coated Tool

The high speed milling of silicon carbide was discussed by using flat end-mill 2 mm in diameter diamond coated tool. Ultra-precision high speed spindle attachment was used to achieve cutting tool rotation speed as high as 50,000 rpm. Special fixture was designed to minimize the chatter on work-piece surface during the machining process. Three cutting parameters were selected as independent variables of the experiments. They were spindle speed, depth of cut and feed rate. The arithmetic mean value of roughness (Ra) was measured on the work-piece surface as the response of the experiment. Result of the experiment shows that the value of surface roughness can be achieved as low as 0.150 μm. Statistical analysis was provided to study the significant of the model, interaction among the cutting parameters and their effects to the surface roughness value.

Sign in / Sign up

Export Citation Format

Share Document