Synthesis of Triethynylborazine-Polyhydromethylsiloxane Copolymers and its Ceramization

2013 ◽  
Vol 774-776 ◽  
pp. 629-633
Author(s):  
Ji Feng Jiang ◽  
Kang Kang Guo ◽  
Ya Ping Zhu ◽  
Fan Wang ◽  
Hui Min Qi
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Nuclear Magnetic Resonance ◽  
Fourier Transform ◽  
Thermogravimetric Analysis ◽  
X Ray Diffraction ◽  
Hydrosilylation Reaction ◽  
X Ray ◽  
Ft Ir ◽  
Scanning Electron

Triethynylborazine-polyhydromethylsiloxane copolymers (TEB-PHMSs) were prepared through hydrosilylation reaction between -C≡CH attached to boron and ≡Si-H. The structures of TEB-PHMSs were characterized by Fourier transform Infrared (FT-IR) and Nuclear Magnetic Resonance (NMR) spectroscopy. Their cure behavior were examined by Differential Scanning Calorimeter (DSC) and FT-IR, and then thermostability and ceramization of cured TEB-PHMS were investigated by Thermogravimetric analysis (TGA), pyrolysis-GC-MS, X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). The results indicated that TEB-PHMSs could be cured and converted into an outstanding thermostable SiBCN ceramics.

Optimization of ammonia nitrogen removal by SO42− intercalated hydrotalcite using response surface methodology

RSC Advances ◽  
2016 ◽  
Vol 6 (54) ◽  
pp. 48329-48335 ◽  
Author(s):  
Heng-Zhi Duan ◽  
Hong-Yan Zeng ◽  
Hua-Miao Xiao ◽  
Chao-Rong Chen ◽  
Gao-Fei Xiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Response Surface Methodology ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Ammonia Nitrogen ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir ◽  
Scanning Electron

SO42− intercalated Mg–Al hydrotalcite (S-LDH) was prepared under microwave irradiation and characterized by powder X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM).

Preparation of PVA/ Sm(NO3)3-Sm2O3 Composites Nanofibers by Electrospinning Technique

2010 ◽  
Vol 71 ◽  
pp. 22-27 ◽  
Author(s):  
Patrizia Frontera ◽  
Concetta Busacca ◽  
Vincenza Modafferi ◽  
Pierluigi Antonucci ◽  
Massimiliano Lo Faro
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Thermogravimetric Analysis ◽  
Fourier Transform Infrared Spectroscopy ◽  
X Ray Diffraction ◽  
Electrospinning Technique ◽  
X Ray ◽  
Scanning Electron

. In this work PVA/Sm2O3 composite fibers and Sm2O3 fibers (PVA and Sm(NO3)3 were used as precursors) were prepared by using electrospinning technique. The fibers obtained were characterized by scanning electron microscopy, X-ray diffraction, thermogravimetric analysis and Fourier transform infrared spectroscopy.

PENINGKATAN LAJU DISOLUSI ACYCLOVIR DENGAN METODE SISTEM DISPERSI PADAT MENGGUNAKAN POLOXAMER 188

2016 ◽  
Vol 5 (1) ◽  
pp. 6
Author(s):  
Budi Setiawan ◽  
Erizal Zaini ◽  
Salman Umar
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Differential Thermal Analysis ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
Poloxamer 188 ◽  
X Ray ◽  
Scanning Electron

Sebuah penelitian tentang sistem dispersi padat dari asiklovir dengan poloxamer 188 telah dilakukan formulasi dengan pencampuran secara fisika dengan rasio 1 : 1, 1 : 3, 1 : 5 dan dispersi padat 1 : 1, 1 : 3, 1 : 5 dan penggilingan 1:1 sebagai pembanding. Dispersi padat dibuat menggunakan metode pencairan (fusi), yang digabung dengan poloxamer 188 pada hotplate kemudian asiklovir dimasukkan ke dalam hasil poloxamer 188 lalu di kocok hingga membentuk masa homogen. Semua formula yang terbentuk termasuk asiklovir poloxamer 188 murni dianalisis karakterisasinya dengan Differential Thermal Analysis (DTA), X-ray Diffraction, Scanning Electron Microscopy (SEM), dan Fourier Transform Infrared (FTIR), kemudian pengambilan dilakukan  (penentuan kadar) mengunakan spektrofotometer UV pada panjang gelombang 257,08 nm dan uji laju disolusi dengan aquadest bebas CO2 menggunakan metode dayung. Hasil pengambilan  (penentuan kadar) menunjukkan bahwa semua formula memenuhi persyaratan farmakope Amerika edisi 30 dan farmakope Indonesia edisi 4 yaitu 95-110%. Sedangkan hasil uji laju disolusi untuk campuran fisik 1: 1, dan dispersi padat 1: 1, dan penggilingan 1: 1 menunjukkan peningkatan yang nyata dibandingkan asiklovir murni. Hal ini juga dapat dilihat dari hasil perhitungan statistik  menggunakan analisis varian satu arah  SPSS 17.

Preparation of Borosilicate Xerogel and Research on its Mineralization

2012 ◽  
Vol 476-478 ◽  
pp. 2059-2062
Author(s):  
Chen Wang ◽  
Ya Dong Li ◽  
Gu Qiao Ding
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Ph Value ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Compositional Changes ◽  
Scanning Electron

Tributyl borate was first adopted for the introduction of boron in the preparation of bioactive borosilicate xerogel by sol-gel method. The xerogel reacted continuously in 0.25M K2HPO4 solution with a starting pH value of 7.0 at 37 °C for 1day. The structural, morphologies and compositional changes resulting from the conversion were characterized using X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy. The results indicated that speed of formation of HA was cut way back on the time with the addition of boron and the induction period for the HA nucleation on the surface of the borosilicate xerogel was short than 1 days. The conversion mechanism of the borosilicate xerogels to hydroxyapaptite was also discussed.

scholarly journals A Novel Strong Cyan Luminescence Emission of Tb2O3 Particles

2021 ◽  
Author(s):  
Fatma Unal
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Ammonium Carbonate ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Terbium Oxide ◽  
X Ray ◽  
Ft Ir ◽  
Pl Emission ◽  
Scanning Electron

Abstract Terbium oxide (Tb2O3) particles (NPs) were synthesized by precipitation method using ammonium carbonate as precipitation agent. Effects of precursor molarity (0.1, 0.15 and 0.2 M) on photoluminescence (PL) behaviour of the NPs were investigated. The presence of the Tb2O3 phase was confirmed by X-Ray Diffraction (XRD) and Fourier-transform infrared spectroscopy (FT-IR) analyses. Morphological investigations of the produced powders were made by Field Emission Gun-Scanning Electron Microscopy (FEG-SEM). It showed that the morphology of Tb2O3 particles transformed from the nanograin chain to bundles morphology of rod-like as the amount of precursor molarity increased. Emission spectrum were investigated by Photoluminescence (PL) Spectroscopy. All the Tb2O3 particles exhibited the strongest peak at 493 nm ascribed to 5D4-7F6 (magnetic dipole (MD), C2) transition. The increase in the number of C2 sites released from the MD transition with the increase of the precursor molarity caused a negative increase in the b* (yellowness/blueness of the emission) value in the CIE diagram, indicating that the colour shifted to the blue region. The Tb2O3 particles produced by the precipitation method exhibited novel strong cyan colour and the PL emission intensity increased with increasing molarity.

scholarly journals The Characteristics of Padamarang Magnesite under Calcination and Hydrothermal Treatment

2019 ◽  
Vol 29 (2) ◽  
Author(s):  
Mutia Dewi Yuniati ◽  
Feronika Cinthya Mawarni Putri Wawuru ◽  
Anggoro Tri Mursito ◽  
Iwan Setiawan ◽  
Lediyantje Lintjewas
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Fourier Transform Infrared Spectroscopy ◽  
Hydrothermal Treatment ◽  
Energy Dispersive ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Magnesite (MgCO3) is the main source for production of magnesium and its compound. In Indonesia, magnesite is quite rare and can be only found in limited amount in Padamarang Island, Southeast Sulawesi Provence. Thus the properties of magnesite and the reactivity degree of the obtained product are of technological importance. The aim of this work was to analyze the characteristics of Padamarang magnesite under calcination and hydrothermal treatment processes. The processes were carried out at various temperatures with range of 150-900°C for 30 minutes. The solids were characterized with respect to their chemical and physical properties by using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Fourier-transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD). SEM image indicates that magnesite was formed from thin and flat hexagon sheets. The FTIR and XRD analysis disclose that MgO formed at temperature above 300°C, where as the magnesite sample also lost its mass around 50%. These results demonstrate that Padamarang magnesite decomposes to magnesium oxide and carbon dioxide at high temperature.Magnesit (MgCO3) merupakan sumber utama untuk produksi magnesium dan senyawa-senyawanya. Di Indonesia, magnesit cukup jarang dan hanya dapat ditemukan dalam jumlah yang terbatas di Pulau Padamarang, Propinsi Sulawesi Tenggara. Oleh karena itu sifat magnesit dan derajat reaktivitas dari produk-produk magnesit penting untuk diketahui. Penelitian ini bertujuan untuk menganalisis karakteristik magnesit Padamarang dengan perlakuan kalsinasi dan hidrothermal.  Proses dilakukan pada temperatur yang bervariasi dari 150-900°C selama 30 menit. Sifat kimia dan fisika dari magnesit dikarakterisasi dengan menggunakan scanning electron microscopy dengan energy-dispersive X-ray spectroscopy (SEM-EDX), Fourier-transform infrared spectroscopy (FTIR), dan X-ray diffraction (XRD). Gambar dari analisis SEM menunjukkan bahwa magnesit terbentuk dari lembaran-lembaran heksagonal yang tipis dan datar. Hasil analisis dengan FTIR dan XRD menunjukkan bahwa MgO terbentuk pada temperatur diatas 300°C, dimana sampel magnesit juga kehilangan massanya sekitar 50% pada suhu tersebut. Hal ini menunjukkan bahwa Magnesit Padamarang terdekomposisi menjadi magnesium oksida dan karbon dioksida pada temperatur tinggi.

The Characterization of Bovine Bone-Derived Hydroxyapatite Isolated Using Novel Non-Hazardous Method

2020 ◽  
Vol 45 ◽  
pp. 49-56
Author(s):  
Aniek Setiya Budiatin ◽  
Samirah ◽  
Maria Apriliani Gani ◽  
Wenny Putri Nilamsari ◽  
Chrismawan Ardianto ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Extraction Method ◽  
Bovine Bone ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir ◽  
Novel Method ◽  
Scanning Electron

Bovine bone is a considerable source for the production of hydroxyapatite. The recent study reported a novel method to extract hydroxyapatite from bovine bone without producing hazardous residue. The bovine bones were cut and boiled in the opened chamber followed by boiling in pressurized tank. The bones were then soaked into 95% ethanol. Calcination was then conducted in 800°C, 900°C and 1,000°C, for 2 hours. The result was then grinded and sieved. The powder then was characterized using Fourier transform infrared (FT-IR), Scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD) to measure the purity of hydroxyapatite. It is concluded that the hydroxyapatite derived from this process showed 100% purity, resulting 35.34 ± 0.39% w/w from the wet bone weight and 72.3% w/w from the dried weight. The present extraction method has been proven to yield high amount of pure hydroxyapatite as well as reducing the use of hazardous reagent.

Biocidal activity of curcumin and cationic polymer possessing composites

2020 ◽  
Vol 35 (4-5) ◽  
pp. 389-398
Author(s):  
Tarık Eren ◽  
Gülay Baysal ◽  
Faik Doğan
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Curcuma Longa ◽  
Antibacterial Properties ◽  
Fourier Transform Infrared ◽  
Diffusion Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

There is a growing interest in new type of biocidal compounds with antibacterial properties against bacteria. In this study, new antibacterial synthetic materials bearing curcumin and cationic polymers were synthesized. In the synthesis stage, the methacrylate functional cationic monomer was synthesized via the Michael addition route by using 3-acryloxy-2-hydroxypropyl methacrylate and 3-amino pyridine to obtain Monomer 1. Monomer 1 was further quaternized with hexyl bromide to obtain a cationic methacrylate functional monomer. Free-radical polymerization of Monomer 1 and methyl acrylate was conducted in the presence of azobisisobutyronitrile under dimethylformamide solvent. The composite formulation was conducted by using turmeric extract Curcuma longa (curcumin), hydroxyapatite, montmorillonite, and silver nitrate. The materials were analyzed by using the methods of X-ray diffraction, nuclear magnetic resonance, Fourier transform infrared spectroscopy, and scanning electron microscopy. The biocidal activities against the bacteria Escherichia coli, Listeria monocytogenes, Salmonella, and Staphylococcus aureus were analyzed using agar well diffusion method. From the Fourier transform infrared, X-ray diffraction, and scanning electron microscopy analysis results of the synthesized nanocomposites, it is seen that they form strong connections with the components added to the composites and form an exfoliated structure. According to the antibacterial analysis results, the nanocomposites obtained have showed a strong antibacterial resistance against E.coli, L.monocytogenes, Salmonella, and S. aureus bacteria, and the high inhibition zone areas were obtained.

Sign in / Sign up

Export Citation Format

Share Document